when you put a solid flywheel on the genuine ford kit utilises the pulley of a fwd one with no rubber damper ......which is nice
@MrVxrman
Жыл бұрын
Nice work Jerry 😎
@hoggmotorsport
Жыл бұрын
Stupid idea of a pulley 🤦♂️ Spot on mate 👍
@jerryexplores7587
Жыл бұрын
Yer dump idea only took my 2 hours to fix so not to bad.cheers
@CookTalknTravel
21 күн бұрын
Hi how much it would cost to get it replaced, just towed my vehicle to a workshop for the same trouble. waiting for the quote
@jerryexplores7587
20 күн бұрын
Hi crankshaft pulley cost me £80 I think . Should take a couple of hours max to fit it. Easy job.
@tonyprice1526
3 күн бұрын
I'm trying to get mine off with the engine in gear but the pully is turning. How did you get the bolts out without this happening?
@jerryexplores7587
3 күн бұрын
@tonyprice1526 use another socket and long bar to hold one of the other bolts .or use an impact gun to undo them.
@andyking05
Жыл бұрын
Yeh nice one, the bit that’s the tricky bit you forgot to record! How do you hold it from turning as you undo the three bolts??
@jerryexplores7587
Жыл бұрын
Yer, sorry, I used another bar and socket on the other bolt.
@andyking05
Жыл бұрын
@@jerryexplores7587 cheers for replying mate mine are soo soo tight
@wildfruits477
Жыл бұрын
what did u use mate to stop the pulls from moving whilst you undid the bolts to pulls, also do you have to remove front part on bumper and fan or can it be done with out
@jerryexplores7587
Жыл бұрын
Thanks for watching. It's easier to do the job if you remove the bumper and radiator. I used 2 long bars with sockets on .I put one socket with bar resting on the chassis while I undid another to hold it still if that makes sense.
@anthonykinrade8642
Жыл бұрын
Did it squeal a lot leading up to and before it broke?
@jerryexplores7587
Жыл бұрын
No mate it just snapped off. The brakes and steering stopped. Shit me pants.
@scottdugmore3420
Жыл бұрын
mine did mate i thought it was the idler pulley so changed that but still the same an then this went currently doin the job now bolts come out easy if you have a impact gun
@getur99
9 ай бұрын
Are the bolts reusable? Or are they stretch bolts? Did you use loctite on reinstall?
@jerryexplores7587
9 ай бұрын
I used new bolts and loctite.
@vincemarshall8550
9 ай бұрын
you can use em 3 times but if its second hand probly best to replace
@aaronmaloney8
5 ай бұрын
Mine needs replacing, making a rattling nosie like hard plastic. Is it safe to drive ?
@jerryexplores7587
5 ай бұрын
Open the bonnet and check to see if it's lose.
@aaronmaloney8
4 ай бұрын
She isnt loose at all, is this job that easy? Can the belt go on wrong, how tricky is this job , thx @jerryexplores7587
@aaronmaloney8
4 ай бұрын
@@jerryexplores7587probably going to challenge this myself
@jerryexplores7587
4 ай бұрын
When you have the front striped, make a drawing of how the belt fits.
@Smith-os1ho
Жыл бұрын
Thoughts on a solid crank pulley
@jerryexplores7587
4 ай бұрын
Yer good idea
@user-fz6gp7ek5y
7 ай бұрын
So how long did it take in total?
@jerryexplores7587
7 ай бұрын
Less than 2 hours mate
@campervan-john
Жыл бұрын
Is that a d.i.y garage?
@jerryexplores7587
Жыл бұрын
It's a garage i work at cheers
@campervan-john
Жыл бұрын
@@jerryexplores7587 Oh i never knew,i thought you were a school teacher for some reason 👍
@udstm
Жыл бұрын
Is that on the 2.2 or the 2.4
@jerryexplores7587
Жыл бұрын
2.4 mate
@udstm
Жыл бұрын
As I have exactly the same issue I have the torn belt and the outside of the pulley with the centre still attached
Пікірлер: 37