The best Transmission Shudder Fix Additive out there- amzn.to/3rLXg02
@whpony96
10 ай бұрын
Hey Brian do you use one or two tubes for the 2018 Explorer Platinum?
@gloryland59
10 ай бұрын
Hey, should I use this for a maintenance procedure.
@21Piloteer
10 ай бұрын
I used it in my old 09 Impala that developed a shudder. Used this additive....doesn't work.
@JohnR9965
10 ай бұрын
Brian. Do you still have a Quincy air compressor? If so what model is it. I need to buy a new one. Any recommendations ?
@Quick_Fast_Hurry
10 ай бұрын
If I own a VCM3 will you offer a remote diagnostics session if I pay for a retainer/deposit for an 08 flex fuel 5.4l crank no start condition? I apologize I already reset cam
@steveturner3999
10 ай бұрын
Thanks Brian! I love that you reached out to find the source of this problem. In my opinion it makes you even more of a great mechanic.
@Jimmy-nv7mn
10 ай бұрын
Great troubleshooting using the gopro to be able to see the problem under dynamic conditions. Nothing more frustrating than not being able to see the problem as it's happening
@garyfletcher8458
10 ай бұрын
I worked at a Chrysler dealer in the early 90's and this was a very common problem with inner CV joints. They did not use a circlip but used a spring inside the inner CV joint housing to keep the CV joint in the trans. When these went bad it would cause the vehicle to shake side to side on acceleration.
@paulreed563
10 ай бұрын
Yep, I had a 1986 Dodge Aries that did this same thing, had actually worn an indent into one of the tripod cups. Drove me crazy. Finally gave a tech at a dealer $20 to take a quick ride with me and he told me what it was within about 30 seconds of driving.
@lvsqcsl
10 ай бұрын
Yep, I had a 1983 Chrysler New Yorker that did the same thing. The tripod bearing had actually frozen and when I jacked up the front and spun the wheels with my foot on the brake it would actually move the engine from side to side. I think it had the 2.6 liter Mitsubishi "silent shaft' engine.
@paulreed563
10 ай бұрын
The 2.6L HEMI!
@lvsqcsl
10 ай бұрын
@@paulreed563Yeah, a real stormer. The customer that had that car traded it for a 1986 Fifth Avenue and it had the 318 with all of 140 horsepower. Another "stormer."
@eegg6954
10 ай бұрын
An yes. Remember when Chrysler sold Horizons and Omnis to police departments? Hahaha! Couldn't make this stuff up! And I was a fleet service rep. What a sh-t job back then.
@dennisthompson44
10 ай бұрын
I have watched your channel for awhile. I totally rebuilt a 5.4 3 valve and after fixing some wiring issues it runs great . I just had to say with your inspiration that it can be fixed it kept me going. I am very happy to say it is better than new. My parents owned the truck before me. My late father would be proud I fixed it. My mother said it is riding better than when it was new from the factory. I did have to bore it 0.020 over because it melted through the #4 piston. When this engine is running right it is awesome. Again thank you for your inspiration it kept me going. I will continue to watch your channel and I pass your channel on to all my friends. You are doing a great service to the diy's out there. Helping those of us who are not wealthy but have motivation to fix it ourselves. Again many thanks
@Bereft777
10 ай бұрын
A geat example of balanced repairs of each axle. You touch one side do other.
@ninjasfanfunnystuff9026
10 ай бұрын
2 months ago I had the EXACT same situation on the wife's 2014 Exploerer. Replaced rear driveshaft, motor mounts. It was the RH CV shaft! Problem fixed! Exact same symptoms as you!
@dennisthompson44
10 ай бұрын
Ps for anyone looking at this thread. Everything he has said about fords has been spot on. I don't even question it anymore. It always is the way he says.
@jmaxim80
10 ай бұрын
I dont care for Ford personally, but I love what you do, and you are a hell of a professional, in my opinion. Keep up the great work, brother.
@richardthomas1743
10 ай бұрын
Thank you Brain for letting us know about this! It is good information to have!
@roscoe_t
10 ай бұрын
As a DiYer, Lubegard products (including Shudder Fixx) helped me take a 1994 zF 5hp30 transmission 300k miles. The torque converter had shudder problems from the start, as a service bulletin from BMW attests. They tried to resolve it with a replacement computer chip, but the friction modifiers in Shudder Fixx did the trick. I kept the clutch chatter at bay with Lubegard Red and a spill and fill every 30k miles. Lubegard is not your average snake oil. The trans was shifting well when I sold the car due to rust.
@d1sternagle
10 ай бұрын
Dude ur energy is awesome, you can see and feel how much you love your work. Keep crushing.
@ecaparts
10 ай бұрын
Impressive... The inner boot held up well, with all the miles and the heat and even with the grease turning to oil! it still looked good from the outside!! That's probably why it was missed. 👍
@user-my1nq9mx4u
6 ай бұрын
Brian, all I want to say is I freaking love you man. I bought my 2009 f150 with the 5.4 3V almost 4 years ago now, and I just rolled 330,000Km. Me & Ol’ Bessie have you to thank!! From motor work, chasing these kind vibrations, everyday maintenance and servicing, etc. Everytime I watch your videos I learn something and go at what I’m working on with a total different confidence. Sincerely man, can’t thank you enough for taking the time to make the videos you have, you’ve helped a struggling 25 year old really love his Ol’ Ford😂 Cheers brother🤟🏻
@TEC_Stuff
10 ай бұрын
Amazing diagnositic process of a difficult scenario. I guess with extreme duty usage, all previous part life expectancy goes out the window. In other words any moving parts could be the culprit. It was good of you to order the part and put it in to prove what was broken. Like another commenter mentioned, if you change things on one side, you should do it on the other side at the same time. I think due to driving dynamics, it’s more important to change parts on both sides of either the front end or the rear end, due to the fact both the left and right sides are going over the same piece of road surface at same time (both left and right of the front end, then both left and right of side of the rear end). Nice troubleshooting!
@fogit4668
10 ай бұрын
About a week before watching this I learned about the Lube Guard Shutter Fix additive. It worked. I bought two tubes and only put one in. Keeping the other tube for the next transmission oil change. Now I have to go and check my transmission mounts to check their condition.
@josephklimchock5412
10 ай бұрын
As an old car guy that did most of my time working on cars in the 70-80's and still work on my own stuff, I love watching you on these videos. I am always a bit amazed at how some cars will have these fail way sooner, and other cars may never need them ever. I sold my 200 Taurus with 220K last year with the original CV axles and it rode as smooth as the day it came off the line. I get that this was cop car so a lot of heavy abuse, start, stop, all kinds of non regular driving during the life as a cop car. The grease probably turned to that fluid due to the extreme heat that the CV joint was creating. My guess.
@svt32vdohc
10 ай бұрын
Agree. As for the CV axles, some OEM's use bad suppliers to cut costs. They will switch to Chinese suppliers, produce 100k vehicles, figure out they're bad and go back to a previous supplier. It's terrible.
@artemis9789
10 ай бұрын
In my time at Honda, vibrations caused by cv shafts were pretty common. It was almost always only on accel, would violently shake the vehicle (think super-duty death wobble) and almost always caused by the inner cup having divots worn into it from the rollers. Somewhere around 1/16" deep divots would cause that vibration. Crazy. Seeing a total bearing failure is impressive though, that doesn't happen often. As always, great content Brian 👍
@shaygleason3585
10 ай бұрын
Had the same exact issue with my 2004 F150. I had the infamous death wobble. Replaced the axle and all gone. The mechanic that replaced it for me thought I lost my mind when I told him it was bad. It looked brand new didn’t look worn never clicked when I made a turn no obvious signs that it was bad but I did notice the way it was sitting on the truck when I looked underneath straight on. No more shaking at higher speeds.
@Patman03sprcrw
10 ай бұрын
Good find! Wasn't top of my list, but makes sense now that I see the failure point
@needforfieros
Ай бұрын
Thank you for posting this. It solved my problem!!!!
@jbstepchild
10 ай бұрын
I wouldnt habe thought that i was gonna say trans mount an maybe k memeber but inner cv very cool
@citabria808
10 ай бұрын
The rustbelt appears to be coming true on that frame under the vehicle. Thank you Brian for these videos. They have saved me several hundreds by showing me how to complete (simple) tasks. Does salt water help change the grease properties, or was the boot sealed and intact?
@londen3547
10 ай бұрын
Shake all that rust away! Makes you wonder why someone would want to throw all that money at a rustbucket like this.
@mph5896
10 ай бұрын
@@londen3547that’s a normal vehicle in the north. Once you can’t pick them up by the pinch welds, then it’s getting close to scrapping them.
@Vchat20
10 ай бұрын
Good info! Relative recently got into a '15 Explorer with high mileage (~130k). Base model non-PI with the NA 3.5 V6 and tow package with the upgraded transmission. It's been fun keeping tabs on potential concerns to watch out for. Knock on wood other than some initial TC shuddering that was solved by topping up the trans fluid, it's been running good even with a ~5k mile road trip tacked on (monitored the slippage in Forscan during the trip and was rock solid). But will definitely be bookmarking the shudder fix for the future since I anticipate that may eventually become a thing as it racks up more miles.
@mph5896
10 ай бұрын
I have a 14 Base with the 3.5, 180k. I bought it with a laundry list of issues. Had 1 bad cat, transfer case was leaking out the pass seal (I drilled and tapped a drain plug as well), water pump external leak, lower control arm rear bushings bad, sway bar links, tires x4, brakes. Did it all at parts cost. Runs and drives great now. Everything I did are common issues on high mileage ones.
@Vchat20
10 ай бұрын
@@mph5896 Yep. A number of those came up at purchase time on this one and were taken care of like the transfer case seal on the passenger side, sway bar links, bushings, etc.. I think the main one we'll be watching for is the water pump. But like yours, this one definitely drives and rides nice despite the mileage. I was pleasantly surprised.
@gmatias1231
3 ай бұрын
I currently have the same problem with my 13. Thank you for the explanation. Luv watching your videos keep up the awesome work.
@GeorgeSellsUpstate
4 күн бұрын
I do too! Mine has 138,000 miles. About to have the cv axles replaces and I will let you know if it fixes the shaking problem.
@ford56798
10 ай бұрын
My wife just traded in her 2020 explorer that would vibrate like a mother at 70 mph. If you went alittle faster or slower it was fine. It was right around 69 to 70 mph. Only had 24k on it. Never really found out what the cause was. This was just one of many issue we had with the explorer. We had a ton of electrical gremlins that Ultimately made the decision easy to just dump it back to the dealer.
@allanwilson6188
4 ай бұрын
I have 2014 limited I was changing struts as soon as I took my strut off my cv axle broke at the knuckle. After replacing CVS and struts on both sides my car drives so much better
@badazz2969
10 ай бұрын
I had this same thing a year ago with a 14 explorer ppv i was scratching my head because it was awd but ordered the drivers side one installed and shake was gone it was the only one with wobble but it was so miniscule yet it shook like mad at 25+
@brentnowell
10 ай бұрын
Grease should not turn into oil. I have seen a case in which an atv inner cv joint did the same thing, liquified the grease. It was actually leaking oil from the diff into the boot via a badly sealed housing. Some of these cv housings have a pressed piece of metal to seperated diff fluid from cv axle grease. You should clean that part up and see if it was passing
@danielthornton1633
Ай бұрын
The day I bought my 2016 explorer sport (a week ago) it was shaking like crazy and I was freaking out because I thought it was the axle. I realized they told me they just put brand new tires on, and I took it to a local shop and the balanced the tires. Boom, sped up to 115 mph on the highway and was SMOOOOTH lol I’m gonna keep an eye on my axles and PTU though! Will be doing my own oil changes every 4000 miles, with the quality oil!
@GrandPitoVic
10 ай бұрын
In the mid 90's till 2000 I had a business rebuilding cv axles and rack and pinions and steering gear boxes and also power steering pumps. We had a Camry with that same issue. Slamming the drive train back and forth. It ended up being the inner cv axle was messed up. It had came apart lol. I couldn't believe it.
@lesk7282
10 ай бұрын
Good find. Those can be difficult to diagnose at times. I had a 2017 Explorer Limited with a violent shake only during accel worst at around 80 kph. Same thing, drivers axle shaft faulty. Note: I've had no luck with aftermarket cv axles. They're good for awhile and come back with the same concern. For long term fix replace with oe I don't care about the price difference or the life time warranty the aftermarket have. Also have a 2011 Ford edge which has same concern and we keep throwing cv axles on it because they're lifetime warranty so why not 😅. Good for about 30k and soon it begins to shake during accel. The car is the company loaner vehicle.
@gunnerfanning5921
10 ай бұрын
I sometimes wonder, how many times a day Brian, that you walk outside and try to regroup from some of the things that come thru your bays... great content Brian 👍😎
@Northernsledr
5 ай бұрын
i lucky guessed your issue only because i've always used what i was taught that straight-line acceleration shudders are always the inner joint, turning shudders are outers
@timowallin8020
10 ай бұрын
Common Ford Transit Problem and nice thing is that only originals work. If you try aftermarket its like winning lottery if you still don't have the shake. ;)
@paulhudgins5120
10 ай бұрын
Awesome research and awesome fix to find the problems, great job.
@Twobarpsi
10 ай бұрын
Best tech anywhere! I wish you were closer. You would definitely have my business!
@chstimeoff7610
10 ай бұрын
So I think you said you informed the customer and he said to hold off but you went ahead and bought a new shaft on your dime to prove the point that you had not seen this problem to us. If that is correct than I respect you more then you would ever know. I have learned so much from your video's even though I am just a wannabe DIYer. Thank you SIR!!!!!
@FordTechMakuloco
10 ай бұрын
No, he said hold off on the exploratory committee when I still wasn't positive, but I had a hunch and really wanted to find the fix for him.
@kcichon
6 ай бұрын
I can tell you that IDENTICAL symptoms on my 2016 Ford Escape .. same fix despite the fact that dirveshafts looks "OK" when checked by hand ... Replaced form driver side first .. hmm .. gotta replace driver side too. So dont be cheap .. save yourself time, change both at the same time ;-) .. THANX A MILLION for sharing. ANd I was about changing struts .. ehh ..
@MarioDallaRiva
10 ай бұрын
Brian, that CV goop looks just like the McDonald’s hot fudge sundae I had last weekend! 😮
@rodneymiddleton9624
10 ай бұрын
I've had that many times on all different brands. Hard to determine which one. All acceleration vibrations have been CV axles. Thanks!
@nikitaso
4 ай бұрын
I had this issue on 2013, took to 3 mechanics including dealership and no one could identify the problem. Finally found some random video where guy was explaining similar issue but on different vehicle. I forced my mechanic to change CV joints and problem went away lol
@joepalladino3553
10 ай бұрын
Great job explaining the problem and cause. I had a VW Jetta years ago, had axle changed n was getting vibration , they replaced again. No help . Mistake took it dealer ! They said was clutch , replaced no help , replaced all engine n trans mounts! No help. They had car 2 weeks, said internal engine problem can’t fix? Was on VW forum, cannot yes aftermarket solid axle! Put in VW axle ok! Screwed by Dealer!
@brianturner4382
10 ай бұрын
I have 2012 dodge Journey with the exact same symptom. I put new cv shafts in it but the were aftermarket. It was driving me nuts because I couldn’t find the vibration. I came across this video, so I put a oem cv shaft in it and the vibration is totally gone. I couldn’t believe it. Oem cost 3 times as much but it’s the only way to go. Thanks for the video.. I have learned a lot from you
@Fjord_Driver
9 ай бұрын
2001 F150 5.4, 2-valve, 4x4, 258k miles. Drivers side hub and half shaft replaced. Passenger side still fine pushing closer to 277k miles now. Original trans. Lucas stop slip in it. Yes, it helps. Edging closer to trans replacement/rebuild time. Don't put many miles on it per year now.
@malekodesouza7255
10 ай бұрын
As a retired LEO I can tell you that SUV has idled forever and was beaten daily.
@D2O2
10 ай бұрын
Yeah, I bet that engine has close to 7k hours on it, or double the hours of a normal vehicle with 130k miles.
@malekodesouza7255
10 ай бұрын
@@D2O2no doubt. Plus it’s been driven hard… I mean HARD.
@fhrk1991
10 ай бұрын
@FordTechMakuloco if you have a vcmm beside the vcm3 you might want to try-out the vibration sensor, it makes it fairly easy to sort out what causes the vibration.
@bakerd13
10 ай бұрын
The explanation was excellent. Thank you, Brian!
@MarkJones-sk6vk
10 ай бұрын
So looking back, the owner should have taken the axles apart and inspected them? Seems like he really didn't really do too bad. Maybe a few extra parts bought?
@JD-xd5dh
9 ай бұрын
Recently bought an 04 F150 with the 5.4 3v and love catching up on all the videos. It’s already needed plugs, brakes, 4wd hub actuators, ac condenser and accumulator. Looks like timing job has already been done. Look forward to doing as much maintenance as I can on my own with your help. Thank you for the videos!
@markk3652
10 ай бұрын
This is funny, I had a 1997 grand caravan that we bought new in August of 97. It was the wife's car till it became mine after it hit 100000 miles. It suffered from the exact problem you showed in the video. I won't get into the whole story about it, needless to say, the van had a really terrible event happen to it preceding the whole shaking issue. I had the stub axles changed out twice, but no correction to the problem. I decided to change them out myself the final third set, and upon install, it drove smooth as glass again. I found out tbe mechanic that had changed them out twice was ordering remanufactured units. I installed brand new units. I drove that van for three years before I figured it out, even the Dodge dealer was scratching their heads telling me that the differential bearings in the transaxle were bad. I even changed out the motor mounts with no solution to the problem.
@miketeeveedub5779
10 ай бұрын
Obviously this police interceptor had the "Margarita half-shaft" package, to make patrols more tolerable. 😆 On a serious note I thought it was just bad trans/motor mounts, but that CV joint identified as a jackhammer. No wonder that trans mount failed like it did! Lesson learned: replace half-shafts if over 100K. Great video as usual Brian! Cheers!
@tincankiller6454
10 ай бұрын
Very cool video looks like the Tripod became a Bipod slowly becoming a Monopod no wonder it was causing such a ruckus. Thanks for the video.
@brutonstreettailor4570
10 ай бұрын
Brian, i had this exact same issue months after my Ford dealer replaced my front rhs suspension spring, on my Ford Escape Kuga ( in the UK) went out and at 50 mph the bonnet was shaking violently, and i thought my teeth were falling out , though they denied doing it turns out they cut through the inner driveshaft joint boot as they accidentally dislocated the joint whilst swapping the spring out, didn’t tell me and then bodged the refitting so it spun all the grease out , by 9 months down the road when i spotted it , they said tough and that the boot could of been cut by me mounting a kerb. Cost me a new driveshaft for their incompetence, Il never darken their door with my shadow ever again !! Love your channel.
@gregjohnson2073
10 ай бұрын
Always get underneath and check their work.
@anthonyvon4531
10 ай бұрын
I had shudder on my car. I used Lubegard and the shudder was gone. I'm at 30,000 since I put it in. No shudder, not once. Shifts perfect!
@wellnessotr
10 ай бұрын
Neat! Thank you for explaining how it works. I have a Nissan, but I’m very curious about vehicle repair in general.
@jaccoonderdijk1777
10 ай бұрын
Just so cool as a non technician, though with some technical interest, this is so interesting!!
@cheapers1952
10 ай бұрын
I've encountered this on Honda VW and Chrysler it always happens under the load and is caused by the inboard joint on the axle shafts those are the only three I have ever encountered this from Usually clacking on turns is the outboard joint sometimes some wheel Hop included a bid culprit in the past on this was Hyundai and Mitsubishi😮
@76LTD
10 ай бұрын
Had the same thing on my 2001 Honda Civic I could not see it split on the inner boot when I looked and did not probe it for brakeage. Once I removed the steering knuckle to change them out the CV axle split apart and fell. I thought how luck I was as I drove it around trying to troubleshoot it.
@johnwaby4321
10 ай бұрын
Yes sometimes you have to see what's going on to track down the problem 👍👍👍👍
@mikechiodetti4482
10 ай бұрын
If it's a police vehicle, all bets are off! Extreme wear is the norm! If it moves or rotates, it's gonna need repair or replacing. Good one Brian!
@BABA-ws5eo
8 ай бұрын
Great case study. I like how you used the gopro. Even though it didn't solve the issue, I'm sure it helped to narrow it down to some degree. thanks!!!
@GJ-yx3tm
10 ай бұрын
Great info Brian. Thanks forn sharing. Your a great tech, but no one knows it all. Expertise is gained through situations like this. Good stuff. Thanks again.
@FordTechMakuloco
10 ай бұрын
Definitely this is exactly why I will never say I know everything about cars.
@dhonnoll78
10 ай бұрын
Wife had a 13 Explorer actually did not have crazy vibration but when I did her turbo, I noticed the right axle shaft mount was broken in 2. The replacement part used 3 bolts in the engine to support he intermediate shaft before the half shaft. No recall but the part was larger held the shaft over a larger area and much improved.
@williammchugh3659
10 ай бұрын
I rebuilt CV shafts about 22 or so years ago. That type of damage was not at all uncommon back then either.
@inverseuniverse5727
10 ай бұрын
All these new Chinese aftermarket axles are junk . I need inner joint for rx330
@robertmedina6875
10 ай бұрын
YOU ARE THE MAN! Thanks for sharing Brian!
@dansaver8247
10 ай бұрын
Good diagnoses on all problems. Good, clear explanation and video shots. Thank you.
@fredsalter1915
10 ай бұрын
Superb vid!!!
@FordTechMakuloco
10 ай бұрын
Thanks!!
@justinhayward5027
10 ай бұрын
Dude I had a similar issue with a town and country. Couldn’t find nothing eventually I found out it was fix a flat in one of the tires. High speed shaking violently. Drove me nuts. Felt like axle shaft shutter
@eddiereichel9354
10 ай бұрын
If transmission fluid gets changed most of em dont have problems. THe problem with that is people dont change transmission fluid until they have a problem which is in most cases too late.
@eurbanautotech
10 ай бұрын
That makes sense! I ran into this a few months ago. Can't remember the car. Toyota Camry maybe..? This is exactly what it was doing. Felt like the whole subframe was slamming back and forth upon acceleration but all the mounts and bushings were good. We just gave it a quick look and the vehicle never came back so never got a conclusion out of it but after seeing this I'd be willing to put money on this being the issue.
@williamvaughan1218
8 ай бұрын
I had the same problem on a toyota. turned out the previous shop that replaced the transmission had hyperextended the cv joint. crazy symptoms.
@chrisliberty1773
10 ай бұрын
Very common from my time working for Kia, Sedona circa 2007-2010-ish minivans particularly, inner tripod joint goes bad and...same problem
@dotskip
10 ай бұрын
Nice Job !
@johnbarton1878
10 ай бұрын
My 2016 limited pulls severely to the left on acceleration, had it to the dealership several times to no avail. Wondering if the torque steer is being caused by cv axles.
@AP-xq3jm
3 ай бұрын
My 2016 MKX is doing the same thing. I found this video after I found the problem.
@lvsqcsl
10 ай бұрын
I think Ford switched the Explorer to rear-wheel drive in 2019, however I would assume they won't hold up much better. GREAT VIDEO!
@jamesbruno5896
10 ай бұрын
Great info as always Brian thank you!
@paulfiebke3909
3 ай бұрын
Keep up the good work
@gerrymoeller
10 ай бұрын
I've had this issue one time with a Cadillac STS about 15 years ago. Grease was fine on it but it was super loose..
@mrlodge8458
10 ай бұрын
Vibration on acceleration with old Fords was always inner driveshaft joints
@patrickgomez3419
10 ай бұрын
If you grab the driveshaft at the middle section and push up and down and you get play, the drivehsaft is worn and will cause a vibration, been there plenty of times working on Hondas for 24 years
@stagggerlee
10 ай бұрын
My 09 flex was has a similar problem, A vibration under light load at speed when you try to hold speed on a slight grade. Not severe like your explorer, but really annoying. Feels like a fish bite miss. Did do plugs, reduced it, but still there. My guy replaced aft control arm bushings and road force balanced all 4wheels. Its much better, but if it comes back the axles are next. 190k, btw.
@graymodeler
10 ай бұрын
I Had the side to side wobble going up a slight hill on my 2023 Town and Country Chrysler. I used a rebuilt axle but no luck. Then I used a new axle assembly and the problem was gone.
@ddblairco
10 ай бұрын
Good fix
@gza06955
10 ай бұрын
I had torque converter shutter on my 2013 PIU @ 100k and luckily a flush at the Ford dealer fixed it right up
@jeremydoblinger3609
10 ай бұрын
Love to see you a video on proper maintenence interval times for the newer 3.5 ecoboost trucks..oil,trans,diffs and all that..just a thought. Kinda remember to speaking to that at some point..
@FordTechMakuloco
10 ай бұрын
I have a video on that already and it still applies today.
@xr500t
10 ай бұрын
Wow, I thought I'd never see that again! I had a 2000 Honda Odyssey where that happened, when the van was 3 years old! I was on a trip to New Hampshire and all of a sudden a violent vibration started. I looked under all looked great and brand new, 'cause it was... and I ended up thinking that one of the steel belts on the tires had failed? I bought 4 tires 'cause I was certain! but it was not. Ended up replacing the cv axles and solved the problem. No issues after that until its retirement 300k mi later!
@mph5896
10 ай бұрын
I worked on a friends Acura RDX. It had a nasty vibration on acceleration. I replaced the passenger side wheel bearing since it was noisy, along with the passenger side mid shaft bearing and axle. The vibration was still there. The drivers side axle had no indication of failure, but I took a chance and replaced it anyways. Plenty of forums were stating axle issues. Car was fixed. 🙃
@gloryland59
10 ай бұрын
As always, expert videos. Question, my 2005 F150 has a pop when turning to right only ( hard) . New rack, iner- outer rods, struts, shocks. Upper or lower ball joint? Driverside only.
@scout2nut
10 ай бұрын
I saw this same issue back in the 90's on dodge caravans mostly, they would wear a groove inside the outer shell ramp of the inboard plunge joint, under acceleration it would force the lobe into the groove causing that same vibration, bad thing was the CV remanufacturers didn't always catch it and I would create this problem when installing a "new reman" axle, then have to change it out again, not many parts suppliers back then would give a labor warranty, parts only, so I would have to install another one for free.
@bitchenbob5810
10 ай бұрын
Great video!
@ronwilson6186
10 ай бұрын
Another excellent video.
@larrydraper9544
10 ай бұрын
I my humble opinion we both side have the same mileage along being a police package vehicle. Do both sides also inspect front wheel bearings. Great video and diagnosis.
@kevinludlow7462
6 ай бұрын
Thanks..imma check that out next 😊
@odishoodisho4904
10 ай бұрын
Thanks for sharing your experience
@PBAB17
10 ай бұрын
Another reason why I drive a 99 P71.
@jeffreyweinzierl1509
10 ай бұрын
That's whats know as a 3rd order vibration. In other words, it oscillated 3 times for every revolution of the axle. I'm not surprised with the condition of those mounts. Between the sag from the mounts and the drivetrain torquing back on acceleration, that axle was running "flat" and the joint was being pushed back into the tripot to the point where it was hitting bottom and beating itself to death. A police car being driven hard all it's life? No way!
@bradleysteeves7891
20 күн бұрын
I have 2-2017 ford explorer police both over 300,000 kms (200,000mi) both run great appears poluce dept replceds some of these as they look new with stickers onnthem. One does have slight viabration on accelerstion around 75 mph ..i thought bad tire but maybe your video is ibto something. Will look for your video on transmission shutter i have 2014 police taurus AWD transmission shutter at 4o mph. Great videos
Пікірлер: 290