I saw CUAV pixhack V5 ardupilot , it is so cool , thanks so much dear !!
@joeyscustoms
5 жыл бұрын
Very good and awesome research!
@zhangpengsir
5 жыл бұрын
Thank you for your attention
@Dhanjal1911
6 жыл бұрын
美丽 :D
@zhangpengsir
4 жыл бұрын
thanks
@MrSiciro
6 жыл бұрын
nice
@user-fq9ym3vz5b
5 жыл бұрын
_好厲害,我也想學!
@zhangpengsir
4 жыл бұрын
从wiki开始,www.ardupilot.org
@MrCADU267
5 ай бұрын
hey. Is there any way to configure a Pixhawk 6c on the helicopter 450?
@ragazarmani2019
4 жыл бұрын
Can u share the details of the setup? Can u also please share the setup of the helicopter itself like model make and everything i wanna build or buy this system.
@zhangpengsir
4 жыл бұрын
It is recommended to start reading from the official wiki page of Ardupilot, which has a very detailed introduction of each link:ardupilot.org/copter/docs/traditional-helicopters.html
@OzyOzySM
4 жыл бұрын
I think the pixhack 5 has more damping than the pixhawk and even the pixhack 3 use more damping! That is why people use them to manage vibration( low frequency is always problem) also the belt drive is less vibration than TT
@zhangpengsir
4 жыл бұрын
That's right, the Pixhack V5 and Pixhack V3 series have built-in IMU dampers that do filter a portion of the vibration. The belt drive vibration may be smaller than the shaft drive, but it is not absolute. The shaft drive assembly and debugging are in place, and good vibration control can be obtained.
@tommyjakobsen5504
5 жыл бұрын
What setup are you using on transmitter, normal Plane, or helicopter .. that is what i can´t find information anywhere...
@zhangpengsir
5 жыл бұрын
Use wifi radio to connect to the flight control on the plane, and edit the automatic task on the mobile phone ground station to send the flight control to the helicopter. I think if you have operated ardupilot, you should know it when you see it!
@JodyGUY
5 жыл бұрын
How does this differ from other flight controllers used for fpv quadcopters?
@zhangpengsir
5 жыл бұрын
No difference, just when used on a traditional helicopter, debugging is much more difficult.
@thongnguyentan6007
4 жыл бұрын
What size blades you use ? 360 or 380, thanks bro
@zhangpengsir
4 жыл бұрын
420mm blades
@islandisland9594
5 жыл бұрын
Bro ..What the pixhawk PX4 2.4.8 can also be used on helicopters
@cuav8821
5 жыл бұрын
it is pixhack V5 , HAHA
@rshfaim
6 жыл бұрын
Hello, Are you using an external FLB system?
@zhangpengsir
6 жыл бұрын
Rotem Shfaim Did not use the fbl unit, just use the independent pixhack v5 flight control!
@bobochang6661
4 жыл бұрын
张朋大哥 这个地面站和飞控之间的数传是什么解决方案? 我也想在遥控器上放个平板当地面站
@zhangpengsir
4 жыл бұрын
wifi数传,可以近距离通讯
@generationfunk
5 жыл бұрын
Is this easy to set up on a 600 size?
@zhangpengsir
5 жыл бұрын
yes
@OzyOzySM
4 жыл бұрын
dose PIXHAWK V5 is better than this one? I mean newer! did you notice any different in the dampening or vib between the V5 and this one? thank you
@zhangpengsir
4 жыл бұрын
The V5 and V5+ have built-in damping damping, which has a better elimination effect on the mechanical vibration of the helicopter, but the volume and quality will be bigger and heavier. If it is a larger proportion of RC helicopters, it is definitely more suitable for V5 / V5+.
@zhangpengsir
4 жыл бұрын
Sorry, this 420-class RC helicopter, I have now replaced the Pixhack V5 nano flight controller without built-in damping, still have good flight performance, because the V5 nano is smaller, here is its flight video:kzitem.info/news/bejne/2axmt6CKiHaSaqg
@OzyOzySM
4 жыл бұрын
@@zhangpengsir I am thinking to go with v5+ this time for my 900 size homebuild heli I just installed pixhawk 1 for my Trex 450 but I noticed when I do prefligt check the axis not moving only very little When I move the heli left or right or yaw any direction the correction of the FC is very little And the heli will not lift the ground! And shutting off the motor 😠
@zhangpengsir
4 жыл бұрын
The parameters of the total distance and the periodic variable distance to be set are adapted to the mechanical action, and the appropriate flight mode, such as the primary test flight, is used, and the "stablels" mode is used.
@OzyOzySM
4 жыл бұрын
@@zhangpengsir oh so you mean there is no parameters to increase or decrease the FC movments? My other 600 size has better response and more movement when I shake the heli ! The swash and the tail move more ! This one j very little movement ! Thank you for your reply !
Пікірлер: 42