thank god i found this video, best tutorial hands down
@raycaraway3230
Ай бұрын
Thank you. Much appreciated!
@caseihfarmer5231
Жыл бұрын
This video help me a lot I couldn’t figure out why there was 3 spot for the ob2
@corybrown4414
2 жыл бұрын
Thank you for the great step by step . I just bought the auto Cal V3 for a 2019 ram 5500 I've seen several videos where they run a red white black cables through the firewall that plugs into...I believe a crank sensor? My kit did not come with the red white and black wires nor the connector. I believe I just plug mine into the tan and yellow wires to the green wire harness under the steering wheel but I want to Verify. That I definitely do not need is the 3 wire connection going through the firewall to the switch. And I only need the 2 wire connector of the plugs in to the harness under the dash? Thank you in advance for any information You can respond with after watching your video I'm very excited to get it Plugged in and running I'm praying that it will drastically improve my throttle response Off the line from a dead stop. Because right now it is agonizingly slow.
@diegomtz4292
Ай бұрын
Could you do a video on retuning a cummins that already has efi live with a autocal . Had a tuning corruption on mine n been a absolute nightmare trying to retune all cause batteries died and corrupted the tunes on it 🙏
@dirtydieselcustom
Ай бұрын
It won't be any different tuning an already-tuned truck. You should be fine if you recharge the battery and keep a maintainer on it through the next tuning attempt. Low battery voltage is the most common issue we see with tune failures.
@Hibbie2963
Жыл бұрын
Most forums have since banned all discussion concerning EGR/DPF topics. Do you have any suggestion on where to find information and discussion concerning delete?
@KLRunions
2 жыл бұрын
I have the CP3 S&S 30,000 lb upgrade pump on its way ordered through you guys in Kelowna. Considering the full DPF/EGR delete for my 2019 Ram 3500 dually here in Alberta Canada. Tunes available for this truck ? What results can be expected ?
@artbuonauro
2 жыл бұрын
Is this first step to read stock file before downloading the tune?
@anthonysampson5649
3 жыл бұрын
We're having a muffler having effect on my performance
@ian12157
Жыл бұрын
I’m deleting a 2013 Cummins do I have to unplug the air intake throttle control valve before installing the tune.
@cadencope628
9 ай бұрын
Have a 2017, tried to upload tune but gave me error $0281. Tried unplugging and securing connections. Still no luck. When it starts to full flash, it gets to “checking data file” and then says “aborting flash, wrong ecm type” I got a “revised tune” from the diesel dudes and ran it and same problem. What am I dealing with here?
@daltondrews9552
2 жыл бұрын
Can you use jumper cables from another vehicle if you don’t have a battery charger?
@dirtydieselcustom
2 жыл бұрын
Yea that can work, you really just want to make sure your voltage doesn't drop too low. So we have had customers do that with good success.
@TheAirforce17
2 жыл бұрын
I've had to upload 5 tunes in the last month, so I'm tired of this. With a 68rfe, do I have to do a full 500 mile relearn, or 30 miles @30%? Also do I have to relearn all 4 positions?
@johnsonboy1242
3 жыл бұрын
So you can tune it and not do a egr delete or exhaust? Or just do it all at once?
@spiker84
3 жыл бұрын
Once it's tuned the exhaust has to be done pretty quick. The truck will run, but not for long before you run into problems. The EGR can be unplugged and left in the truck with some tunes.
@coreyadams4646
2 ай бұрын
Wow, excellent video. He is my question. I have EFI/live. Currently no switch. Are you telling me I can add a switch just like the video? Next question, can you CTS 2 monitor plug in and work also?
@dirtydieselcustom
2 ай бұрын
You'd have to get a tune that is compatible with SOTF setups, and then you could add the switch. A regular tune will not interact with the switch. The CTS3 will work when plugged into the new OBD2 port and will work normally.
@coreyadams4646
2 ай бұрын
How will I no the sotf switch is working? By idle can you hear it? Or by driving it looking at the fuel mileage by eating the cruise on the highway at 60mph. How do you test urs? Thanks
@dirtydieselcustom
2 ай бұрын
@@coreyadams4646 To test it out you would have it in position 1, and then go near or full throttle and change the position. The switch changes the high load fueling so it's not really noticeable when at low throttle positions.
@coreyadams4646
2 ай бұрын
Muck appreciated, I'll give it a try. Thanks
@Booie603
2 жыл бұрын
Do you ship to California? Also do you have to manually delete DPF ..DEF and EGR in settings after the install ? Thanks
@dirtydieselcustom
2 жыл бұрын
Hey, we can ship tunes and tuners to California, but no removal parts. But once the tune is installed the truck is good to go with those emissions parts removed, no changes to the tune necessary.
@sheawilk11
3 жыл бұрын
I have a question. We did the tuning on our ‘16 Cummins. Then we did the exhaust and EGR delete. It has a 63 cheetah aftermarket turbo. And the problem we’ve run into is a sound that sounds like when a cold 12 valve starts up, but it’s when the truck has to pull itself and then there is a problem loading the boost if your building speed slowly or going up a hill. It sounds like a helicopter. We’ve reflashed it, but I’m worried they didn’t put the turbo specs into the File to be loaded on.
@XxSpeedyxProxX
2 жыл бұрын
Did you this issue fixed my truck started doing this a week after I put the cheetah in? Fleece technical support is leaning towards my tune once I sent them data logs
@SleepyJoeisSlow
Жыл бұрын
Either of you get a fix???
@SleepyJoeisSlow
Жыл бұрын
@@XxSpeedyxProxX fix it?
@derekgreen9086
2 жыл бұрын
Why does it seem like my truck is flying through the gears and pritty much falling on its face power wise?? Any suggestions?? 2016 ram
@RockyMtnWay_406
2 жыл бұрын
I have a 2017 with a intermittently failing turbo actuator. waiting for Chrysler to send me the letter that says they're going to fix it. my question is, has anybody seen this issue go away by doing a full delete kit and tune?
@wizard_of_poz4413
2 жыл бұрын
No that probably won't help it unless they write the tune to turn off vgt which will probably make the drivability shit
@jamesbloodworth4303
Жыл бұрын
My switch is on back order if I install the tunes without the switch can I switch between tunes with the tuner
@559rideordie
10 ай бұрын
Can you tune back to stock with this ?
@michaelroach4977
3 жыл бұрын
My tow tune number 2 sounds completely different smoother no lope at all. is this right?
@chrisleo8890
Жыл бұрын
What did you find out on this are you talking about idle? I'm wondering also
@TheRiskyRaccoon
3 жыл бұрын
I'm doing a full delete on my 16 Ram. Should I load the tune before or after I remove the emissions?
@dirtydieselcustom
3 жыл бұрын
We recommend loading the tune and running the truck quickly before deleting any parts. In case the truck doesn't take to the aftermarket tune (rare but happens) you'll just have to get a stock tune re-loaded to run again, and then we work on finding the cause/make a new tune for the truck. If everything is deleted the truck will have error codes with a stock tune until the new tune is figured out. Cheers!
@Azford83
Ай бұрын
After installing a SOTF can I switch the power setting to a desired HP tune and then remove the switch? Will it stay on that tune?
@raycaraway3230
Ай бұрын
No, it won't stay on that tune. It will default to the stock file setting. There should be separate tune files on your tuner to allow you to tune individually vs. all tune files.
@pochosito
3 жыл бұрын
I NEED HELP. I have 2018 cummins with manual transmission and I followed all the steps on the video but I keep getting the CODE $0281. What do I need to do?
@SomeOne-xr6wy
2 жыл бұрын
Are you supposed to leave the bypass cable installed after doing the tune? Is it needed for the switch to function?
@dirtydieselcustom
2 жыл бұрын
Once the tune is installed you can take the cable off.
@evanschippers3943
3 жыл бұрын
So I have a 2018 cummins. I’m doing what you’re doing and getting a $0281 code. I haven’t unlocked the ecm so I’m assuming that’s what my problem is. I didn’t see you unlock the ecm in this video
@pochosito
3 жыл бұрын
I am getting the same code on mine. What did you end up doing?
@evanschippers3943
3 жыл бұрын
@@pochosito hey man, it ended up being the ecm being locked. You have to buy an unlock cable online that reroutes the obd2 plug in. It’s really simple to hook up and my tuner works immediately. Hope this helps!
@pochosito
3 жыл бұрын
@@evanschippers3943 Hey Evan, Thank you for your help. I just got the tune installed yesterday with the bypass cable connected correctly.
@RockyMtnWay_406
2 жыл бұрын
@@evanschippers3943 I thought the kit came with that cable .. no? I'm getting ready to do my 17
@RockyMtnWay_406
2 жыл бұрын
sorry .. yah, 18 needs that cable apparently.
@tylerw.9305
4 ай бұрын
After installing the switch which end do i plug my CTS3 monitor into? The end where my factory obdll once was or the other end under the dash?
@dirtydieselcustom
4 ай бұрын
You would plug it into the new plug, not the original trucks OBD port. Cheers
@peterortiz2080
2 жыл бұрын
it already comes with the cable ?
@Country_tuff
Жыл бұрын
How much for a 2008 ram 2500 to get the device and the tunes
@RedBeardDetails
2 жыл бұрын
But is your check engine light on tho 👀
@dirtydieselcustom
2 жыл бұрын
Not after tuning, the tune updates the ECU to no longer trigger those codes.
@RedBeardDetails
2 жыл бұрын
@@dirtydieselcustom oh well I might just have to buy ur setup then and another question ur 5 switch comes with obd port does that extra one that u slide in there where the old one goes work like the normal one?
@dirtydieselcustom
2 жыл бұрын
@@RedBeardDetails Yea it works the same way, so you can still read any other codes that might come up, or if you've got a gauge pod like a CTS-3 it will read correctly.
@RedBeardDetails
2 жыл бұрын
@@dirtydieselcustom why are you guys not huge wish I can promote you guys somehow
@ANTHONYMARTINEZ-m5o
10 ай бұрын
Can these Tunners be used on multiple trucks? So long the year and the transmission is the same? Or once you use the tunner is it no longer available?
@dirtydieselcustom
10 ай бұрын
The tuner can be used multiple times, but you'll need to get a new tune and vin license for each truck.
@jiggityyjake2992
10 ай бұрын
I’ve read that you don’t want to delete the truck with a check engine light on the dash. I’ve been having trouble with my abs and traction control light dinging on and off in my 2018 ram 2500. Could this pose a problem with the delete if the abs light or traction control are on at the time of deleting? Thanks for any insight.
@dirtydieselcustom
10 ай бұрын
It is better to tune without the engine lights on if that's possible, but like your truck many times we haven't been able to and the tune works just fine.
@jiggityyjake2992
10 ай бұрын
@@dirtydieselcustom thanks for the response!
@Steadierpark
2 жыл бұрын
Wait a minute…I have a 21’ and got a 4 position switch. He said 06-12 and 19+ trucks have a 5 position switch!
@derekgreen9086
Жыл бұрын
i have a 16,, and it came with a 5 position switch.. so does number 5 position not work?????????
@Steadierpark
Жыл бұрын
@@derekgreen9086 you can set the pin number off the back of the sotf knob. Also, try setting it to 5 and see if it switches to tune 5 by looking at your Autocal in view data log mode (all the way at the bottom of the data). Idk about ezlynk, but I’m sure it’s there. If you switch to tune 5 and it’s there, then you have 5 tunes.
@derekgreen9086
Жыл бұрын
Thanks so much
@derekgreen9086
Жыл бұрын
Hey Jay I got another question, so the programmer sent me another tune, so do I have to bring my truck all the way back to stock to download all the files again or can I just plug it in and download that file?? Thanks
@Steadierpark
Жыл бұрын
@@derekgreen9086 you should be able to write right over it. Email or call your tuner for exact instructions. Put a battery charger on. If you have a push button start, must be in run (not acc) and DO NOT take your key fob out of the truck while tuning!
@jared.hake_
3 жыл бұрын
What are all the parts you bought? Efi Live V3 5 position switch male/female OBD connector tune(autocal) all separate?
@dirtydieselcustom
3 жыл бұрын
We sell them as a ready-to-install kit, so the parts installed are what comes in the package. Cheers
@ericfitch7308
3 жыл бұрын
I’ve tried tuning my 2020 truck and having an error code $0502 on the Efi tuner. Do I need to unplug all emission equipment before trying to install new tune? Also you make no mention of the “Cummins unlock cable” in this video. When do you know if you need to use this cable? Any insight would be great as I am having a hard time receiving answers from EFI live tech.
@dirtydieselcustom
3 жыл бұрын
Hey, I'll try and add that as a speech bubble in the video for future reference. The patch cable is needed for 2018+. And that error code according to the EFI website is: Script file not found. Which usually means the tune file hasn't been uploaded to the device correctly.
@domforte2966
2 жыл бұрын
@@dirtydieselcustom I literally just got the tuner from you guys and it’s throwing that code
@dirtydieselcustom
2 жыл бұрын
@@domforte2966 On that last one it ended up being that the cable was loose in its connection to the truck.
@ColtonGrigsby
Жыл бұрын
Did you ever figure it out? I have a 2018 with the same code!
@anthonysampson5649
3 жыл бұрын
Will you be able to tell a difference at idle when you turn your switch
@sticrzy123
2 жыл бұрын
I can’t tell a difference at Idle , if you have a CTS monitor you can watch the rail pressure change
@weepweep2225
7 ай бұрын
Is the CSP5 only for the EFIlive V3? I’m new to this, I’m currently buying a truck that is deleted and has a new PCM installed so now it needs a new tune license uploaded to it I guess 🤷 so trying to figure this out
@dirtydieselcustom
7 ай бұрын
Both the EFI Live and the EZ-Lynk have shift on the fly switch setups, but only the EFI-Live will have the switch as part of the OBD2 port, the EZ-Lynk uses a different style of switch. But our tunes can overwrite the tunes on your truck so if you figure out which SOTF switch you have we can get you a setup that will work to set it up how you'd like.
@weepweep2225
7 ай бұрын
@@dirtydieselcustom ok I may be reaching out to you here shortly. I want this truck and just need it to get back home without going into limp mode
@dirtydieselcustom
7 ай бұрын
@@weepweep2225 Has the ECU been reset to factory?
@weepweep2225
7 ай бұрын
@@dirtydieselcustom the truck was reset back to factory, so now it thinks the emissions is back on the truck and throwing CEL and service Exhaust see dealer now message. He said that he has a H&S mini Max V2? That he is going to try it out when he gets off from work to see if it will tune the new ecm and program the truck. Yall will be the only option I have if that doesn’t work. By the way thank you for your responses I wasn’t expecting that!
@weepweep2225
7 ай бұрын
@@dirtydieselcustom if yall think that won’t work then I can just go ahead and order via yalls program or see what happens with the H&S
@damianfamania3918
Жыл бұрын
How do you load the stock file to the auto cal before deleting and flashing the computer?
@urbangarcia1
Жыл бұрын
You don’t. This thing doesn’t save your stock file, it over writes it. If you need it back to stock you’ve gotta see a dealer and pay them to reflash it
@dday3
2 жыл бұрын
How do you know what program is on 1-4? Do you set the switch tunes individually? For example, fuel economy -tow-street-performance.
@dirtydieselcustom
2 жыл бұрын
The switches are set from lowest power to highest power 1-4, and you can custom select what levels you like, but 1 is lower and higher later.
@dday3
2 жыл бұрын
@@dirtydieselcustom thanks brother
@anthonysampson5649
3 жыл бұрын
So the 5 position switch can be turned into a 4 position switch?
@dirtydieselcustom
3 жыл бұрын
Yep, that little ring changes the lock setup.
@1morecast09
6 ай бұрын
Did u do anything under the hood?
@dirtydieselcustom
6 ай бұрын
After the tune was installed, we removed the EGR and DPF system.
@michealwhynot
Жыл бұрын
Where does that little display screen go?
@urbangarcia1
Жыл бұрын
It gets put away afterwards. It’s not like other tuners where the screen can be mounted somewhere to casually see metrics. This one literally gets disconnected, stored, and forgotten about until you need to read codes, clear codes, or you upgraded a part and want a tune update made by your tuning people.
@hectorsoso2406
3 жыл бұрын
What about 2018 and up
@RaulManriquena
11 ай бұрын
Does the tuner have can tunes??
@dirtydieselcustom
11 ай бұрын
No, this tuner just uploads custom-written tunes. Cheers
@anthonysampson5649
3 жыл бұрын
What does each position of a four switch mean
@dirtydieselcustom
3 жыл бұрын
Different power levels
@hx31277
2 жыл бұрын
Never have I ever heard anyone call a zip tie a zap strap…
@KillerWhale806
Жыл бұрын
A bit Canadian eh?
@anthonytgod659
2 жыл бұрын
After tuning I still Have check engine lights I’m pissed , I have a 12 ram and I have the boot patch downloaded first . Do I just stop there or do I also download the other file labeld cps5 I’m so confused I just don’t want check engine lights ahhh!!!
@zeeee354
Жыл бұрын
You get it figured out?
@hunterb8916
Жыл бұрын
@@zeeee354did you ever figure it out???? Either of you?
@patricksullivan8489
3 жыл бұрын
Where to buy the tuner for 2019 6.7 cummins ho
@dirtydieselcustom
3 жыл бұрын
Hey, we carry those on our site if you're interested. www.dirtydieselcustom.ca/collections/2013-2019-cummins-6-7l-tuners/products/2010-2018-cummins-efi-live-autocal-ccs-tunes Cheers
@handson8912
3 жыл бұрын
How about a 2011 cummins 6.7
@TheReal_JohnDoeSmith
Жыл бұрын
Canadians ehhh
@RaulHernandez-nu2lb
Жыл бұрын
Now with number on the switch is for towing or daily drive?
Пікірлер: 130