just what I was looking for. The book had me confused actually. But after seeing the video THEN referencing the book made more sense. appreciate ya.
@DarlingtonCdarling6
Жыл бұрын
2022 I'm here to learn how to set injector and value thanks 🙏 alot u made me understand what I came here for... How 🙏 🙏 wish i will have the opportunity to learn more from you in your work shop
@bonniedobkin6948
4 жыл бұрын
Uncle Tony says you are very well informed on the procedures your “IRON” requires , knowledge is the power to solutions,,,ALWAYS !
@bvfdfire1
4 жыл бұрын
I know exactly what you mean! I bent every pushrod on a 504 Cummins. on the wrong stroke and no book. and trying top stop. I was young and dumb. LOL. Thanks for going into detail!
@Digginok
4 жыл бұрын
It can happen!
@clydeacor1911
4 жыл бұрын
The old small cam and big cam Cummins are probably the best and most reliable old school engines ever made! Been many times I lost electric power to the engine and had to turn the screw in on the injection pump to get it home.
@Digginok
4 жыл бұрын
I think they are great engines, simple and cheap to maintain. Thanks
@clydeacor1911
4 жыл бұрын
@@Digginok yes they are. The last one we rebuilt was I believe $900 in parts for an in-frame, which covered pistons, liners, bearings, and all gaskets and seals.
@anchorbrandranch
Жыл бұрын
@@clydeacor1911 we are going to try rebuilding the big cam 400 on our water haul truck. I m on the whole internet begging for any helpful advice from those with experience. Cuz we have no experience at all with this ⚓️🐂🙏
@Mientras_Tanto
6 күн бұрын
Why is this method is not for top stop injectors? What's the procedure for top stop then?
@user-po1hk7mk5v
3 жыл бұрын
👌Clear explanation and demonstration 👍👍👍🙌!
@Digginok
3 жыл бұрын
Glad it was helpful!
@greggb3079
4 жыл бұрын
Ahhh yeah, Frank if you could just copy that manual in triplicate, and throw it in the mail to me, that would be great... Hahaha... Sheesh! Are you kidding me. I watched an earlier video you did , I think maybe after a rebuild on this engine. Was as very informative and informative as this one. Wouldn't expect anything less from you. I don't even have a rig like you have, just like watching the work being done. I like that "Paydirt" guy too... I am green with envy you got to meet him in person... Hahaha. Thank you sir. P.S., hope you got on that job you were talking about in your recent live feed earlier. Take care.
@Digginok
4 жыл бұрын
😂 it’s in the email! Thanks for watching, meeting Jeff was great he is the real deal for sure.
@thomaslockley945
2 жыл бұрын
I definitely like this method better is way more simple even though I have watched this video a few times very good details to thank u
@Digginok
2 жыл бұрын
Thanks for watching! This is the preferred method for older non top stop injectors.
@sassafrasvalley1939
4 жыл бұрын
Wow Frank... that’s a whole lot more complicated than setting the valve lash on my trumpet... and you have five more valves to adjust! Just one question... did you have to use a tuning fork to see if she was sharp or flat afterward?
@polarisxp17
6 ай бұрын
any chance you could share what the cummins publication # for that manual is. should show that on the back cover
@zulfiqaroffsetprintingfais9839
11 ай бұрын
Nice
@redtoprich
6 ай бұрын
Thank you sir
@yeidielperez4885
Жыл бұрын
Good afternoon, what part is it? I need to calibrate a Cumins Bic Cam 350, please. I live in Nebrasca.
@niazalishahcalraabdullahsh4705
8 ай бұрын
Great nice 👍 my name Niaz Ali Shah from Pakistan Lahore Pakistan
@mamunmamun4010
3 жыл бұрын
Thanks
@weepweep2225
Жыл бұрын
Hey brother hope all is well. Just had a quick question for you. I’m running the over head on my 400 and noticed my rocker box o rings may be letting oil out. My box has the Allen head screw in the center. Do I need to remove the Allen screw when I take my boxes off then beat the shaft back to install new o rings? Last thing is do I loosen all rockers on the same head before removing the rocker box? Sorry to bother you and I appreciate you sharing this. Your always my go to guy on here
@Digginok
Жыл бұрын
I believe you got it right, just be sure to get the rocker shaft in the proper position as the oil holes have to line up. My rocker boxes are a bit different than yours. I like to loosen the rocker arms, but it is probably not necessary. Be darn sure to not let a push tube get out of the cam followercup. I did that once and it broke a cam follower off. If you make sure they are in place with a flashlight you should be fine. I would definitely run the overhead after the seals and rocker box gaskets are replaced.
@okwesiriukoro1825
10 ай бұрын
I need torque wrench from you 4:24
@blackdogexcavator21
4 жыл бұрын
Good explanation Mr. Frank. What CPL number did you change to when you upgraded the engine components?
@Digginok
4 жыл бұрын
Thanks! Hope I did it right. I think I have it written down somewhere, my memory ain’t that good.
@blackdogexcavator21
4 жыл бұрын
@@Digginok Haha, you got it right my friend. That old 855 should run forever. I love those engines.
@spankyspanky3174
4 ай бұрын
What’s the name of that book you have there ?
@djbillyebundy8964
3 жыл бұрын
Any chance you got a link or have the number for what book your using?
@jaymonroe4138
3 жыл бұрын
I would like to now as well
@weepweep2225
2 жыл бұрын
Hey brother, what if I have jake boxes? Do I remove them in order to adjust my valves then start over and install my jakes?
@Digginok
2 жыл бұрын
I believe that is correct
@thomaslockley945
2 жыл бұрын
Whats the name of that book
@ruxoneto6560
9 ай бұрын
When i set injector & valves i set valve. 014& .023 a mix of old & new i prefer dial indicator on injector , the reason .011 is to tight on intake & .027 on exhaust is too loose. If the exhaust valves tighten up on heavy load, the jake will tighten up first becsuse they are set at .018 so you don't need .027 lash on exhaust& i prefer dial indicator method , the engine always run smoother with dial indicator !! On old small cams with a cam around 1970 & older if you use dial indicator method you should loosen injector & check injector travel with a dial indicator if injector travels more than .170 thousands then you must use torque wrench method or set injector with more travel than the standard .170 by the what the extra travel is.
@jimdorman1550
4 жыл бұрын
I see in the future: how to install Jake's on a Cummins! LoL
@Digginok
4 жыл бұрын
😂
@elbertgane29
3 жыл бұрын
Hi sir thank you for this video it is very informative,.. Sir I ask some question regarding on how much is the injector torque of a NTA855 bigcam engine. Thanks
@VHP7044
3 жыл бұрын
6 in/lb. on big cam engines with top stop injectors. You are basically removing the slack out of the rocker arms on the injectors. You can with experience use your fingers until you just get a little friction on the set screw. You will need to use the big cam procedure to do this. Do not use the procedure in this video. The big cam procedure is using IBC or inner base circle process. If you have a engine with STC or Step Timing Control there are 2 procedures. I found the OBC process works best with the STC equipped engines. I believe the last year for the Small Cam engines was around 1978-1979.
@jakeburrows1058
Жыл бұрын
@@VHP7044 I have an NTA855 Big Cam with the STC injectors, just wanted to clarify, do you know if i use the procedure in this video to carry out the adjustment?
@ruxoneto6560
9 ай бұрын
@@jakeburrows1058 yes use same timing marks , but stc- mvt engines have a bolton pointer that extends toward the driver side about 1" if i remember correctly ( from the pointer casted on timing cover)
@user-gf1jj6wh7f
4 жыл бұрын
👍
@Digginok
4 жыл бұрын
👍
@brandonturner5110
4 жыл бұрын
Mr. Cunningham, how much run time is on the engine since you ran the overhead with the dial? Also, how much is on it all together?
@Digginok
4 жыл бұрын
Good questions, sorry I don’t have solid answers as the odometer currently doesn’t work. I’d guess around total miles since a major rebuild is 500,000 give or take 50,000. Probably 25,000 since the last overhead was done. The reason I did this one was because I replaced the rocker box gasket on the first head. Figure it was a good time to run it again.
@brandonturner5110
4 жыл бұрын
@@Digginok Good to know. Got a couple of 855s that are probably in need of the same. One we think is a small cam 350, can't find any identification, and the other is a BC 2 ntc 300. Keep up the good videos.
@Digginok
4 жыл бұрын
The cam follower boxes are bigger on the big cams, but the overhead is pretty much the same unless you have too stop injectors.
@brandonturner5110
4 жыл бұрын
@@Digginok I'll pull them side by side and compare. The small cam resembles Lil Red's engine. My Bc 2 has a different accessory drive that still has a tag. Thanks for the information Frank.
@Digginok
4 жыл бұрын
Brandon Turner email me if you have questions Cunningfranknham@gmail.com
@somumuniyappan6892
Жыл бұрын
Engine comming Komatsu inner ? Outer? Mm
@CaptKirk1701
4 жыл бұрын
Looks fun! lol
@Digginok
4 жыл бұрын
Not quite as much fun as diggin! Thanks for watching
@tammylott921
3 жыл бұрын
@@Digginok WESTERN TRUCK & TRACTOR REPAIR ,,, LOOK HIM UP ON YOU-TUBE...
@Digginok
3 жыл бұрын
@@tammylott921 I watch Warren, thanks though
@khalidmuhammed5495
2 жыл бұрын
Does this method apply for KTA19? thanks
@Digginok
2 жыл бұрын
Better check the manual
@gerryspang5917
2 жыл бұрын
I set the injectors at 80 inch lbs and intake at 14 thou. And exh at 27 thou. On the outer base circle.
@woos31
4 жыл бұрын
Alright a little red overhead, turnt er up to the black Frank........smoke that is, takes care of skeeters and covids. Matter of fact I blame the epa for gettin the air to clean for the kung-flu can prosper lol
@sanjukr3315
2 жыл бұрын
Book says one full turn but u did half turn please clarify
@cavecustom9724
2 жыл бұрын
hello please tell me where to find the engine number 475 for ordering parts i want to convert my nta 315
@Digginok
2 жыл бұрын
Not sure, but there are some very helpful groups on Facebook, and some Cummins forums online that may be of use to you.
@cavecustom9724
2 жыл бұрын
@@Digginok you can give a link or the name of such a community ?
@user-bj1do5by5j
11 ай бұрын
Sir good morning how to order service manual for Cummins engine
@Digginok
11 ай бұрын
Try eBay
@ngruiyi9194
3 жыл бұрын
Caterpillar3516 engine main bearing tools
@tatatimario
3 жыл бұрын
Patex nman mga tune up 315 cummins tnx
@mrs.eliteearthworks
4 жыл бұрын
I was here 😁
@Digginok
4 жыл бұрын
Now you know how to adjust the valves and injectors on a small cam Cummins! Nice!
@mrs.eliteearthworks
4 жыл бұрын
Digginok next time, if you need help, give me a call!
@Digginok
4 жыл бұрын
I thought I would just drop her off at your place, have her done in an hour??? #outlawtruckin
@mrs.eliteearthworks
4 жыл бұрын
Digginok 😎 Sugar Tits Trucking & Repair
@Digginok
4 жыл бұрын
There ya go!
@ajboitz912
10 ай бұрын
Does it work for a big cam 3?
@Digginok
10 ай бұрын
Not if it has top stop injectors. I think most all of them are top stop injectors.
@ajboitz912
10 ай бұрын
@@Digginok so what’s the method for top stop injectors?
@ajboitz912
10 ай бұрын
@@Digginok I’m doing an adjustment at this moment and so many places are saying so many things I’m just flustered
@Digginok
10 ай бұрын
@@ajboitz912 kzitem.info/news/bejne/sqqGmo6tb3eVg4o start around 13:00
@ajboitz912
10 ай бұрын
@@Digginok you are a life saver thank you so much
@lytruong5940
2 жыл бұрын
I want to buy the book I want to buy the book I want to buy the book
@tatatimario
3 жыл бұрын
Hello po
@73DiamondReo
4 жыл бұрын
she run any different?
@Digginok
4 жыл бұрын
No it was running fine, I changed a leaking rocker box gasket and decided it was a good time to run the overhead again.
@73DiamondReo
4 жыл бұрын
@@Digginok Just wondering because you said the injectors were a little tighter with the dial indicator method.
@lytruong5940
3 жыл бұрын
can i ask for facebook for you? I am a Vietnamese national
@CharlesStanford-gz4sx
14 күн бұрын
Where to you find A-B-C. Mine just has 1-6. 3-4. 5-2?????
@Digginok
13 күн бұрын
What engine are you working on? This is a 1973 small cam. I am not aware of what you you have.
@CharlesStanford-gz4sx
13 күн бұрын
@@Digginok I believe it to be a 290 old military truck
@CharlesStanford-gz4sx
13 күн бұрын
It’s has valve set Marks. 1-6 5-2 4-3
@CharlesStanford-gz4sx
13 күн бұрын
The pulley you are turning to go from A to B mine doesn’t have A or B or C. It just has the 1-6vs
@Digginok
12 күн бұрын
@@CharlesStanford-gz4sx I suppose that is a b c on some engines. I’m not 100 % sure but it seems to be the same in my mind.
@eaglerayban9769
3 жыл бұрын
Can i use this method in a bigcam,72inch/pounds, injector
@Digginok
3 жыл бұрын
guelos Rosales yes it should be the same unless it is a top stop injector
@VHP7044
3 жыл бұрын
Big Cam should have top stop injectors. You will have to use the top stop procedure and set the injectors on the OBC or outer base circle of the cam. Unless you have STC or Step Timing Control
@radwancoco3760
2 жыл бұрын
Kimans
@mikemurphy9790
Жыл бұрын
Question, have a 78 ntc 350 small cam i believe, smokes blue like a wildfire, almost clears up when up to temperature and under load ( the blue turns to dark grey). Could a valve set / overhead injector set possibly resolve this or would you start off with fresh injectors..? Seems to me its fuel making the smoke not engine oil..
Пікірлер: 103