I went to the ultimaker site and only see 5.2.2. Is there supposed to be multiple release times?
@landofbosses7844
Жыл бұрын
Cure only lets me select a 0.4 nozzle size. How can I get it to give me more options than just that? I just swapped my nozzle to a 0.6 but I can't get anything to slice for 0.6
@hendrikjbboss9973
Жыл бұрын
It seems that one cannot change the nozzle size in Cura 5.3. I've looked just about everywhere. It is not in the Extruder settings and one cannot set it in the same place as in 5.2.2. Hopefully someone will know 🤔
@Tyguy266
Жыл бұрын
I just downloaded it last night. But for some reason my CR10 Smart just won't print....been trying for over 2 weeks but just can't get it to print...
@ThantiK
Жыл бұрын
The problem is that you have a CR-10 smart. Every one of them I've run across has been a dud. :[
@Tyguy266
Жыл бұрын
@@ThantiK i keep hearing that lol. it suck man. i had it printing amazing for about a month. then i changed the nozzle and it just hasn't been right. I might just do the manual bed upgrade..
@tyrell519
Жыл бұрын
@@Tyguy266 why doesn't it print? make sure you tighten the nozzle AFTER heating it up to printing temp.
@Tyguy266
Жыл бұрын
@@tyrell519 I will give thay a shot today. But I think either the bed is warped or I am just new lol
@coltenmeredith8899
Жыл бұрын
It could be so many issues. If you just swapped the nozzle, and it won't print, try heating the hotend up to 220 degrees, then tighten the nozzle to 30 inch-pounds. That's the optimal torque. The reason I say that is probably because the nozzle isn't up against the heat break
@ryandavis4689
Жыл бұрын
I bought biqu B1 SE Plus...it came with Cura 4.8.0. what's the latest version o can use with this printer? Does it matter? PC is a Lenovo Yoga 730. Core i7 ⁸⁵⁵⁰u @1.8 GHz 2.0 GHz 64 -bit x64 Windows 10 home version 21h2 Experience pack 120.2212.4190.0
@Pygar2
Жыл бұрын
Link?
@bettydaltonnewbold2019
Жыл бұрын
Question: my completed pieces all have a large "splash" layer at the bottom on all of them that I have to trim off. Is there a Cura (Cura 5.3 for me) setting to stop or reduce this? Thanks very much.
@michaelsorensen7914
Жыл бұрын
You’re not referring to a brim, are you?
@edwardnewbold
Жыл бұрын
@@michaelsorensen7914 - Yes, the BRIM. That was two months ago. Now I have much more knowledge and experience (smile). Am currently using Cura 5.4 without problems now. Thank you.
@michaelsorensen7914
Жыл бұрын
@@edwardnewbold I just started all this about two months ago as well. MUCH more to learn than I realized!
@hendrikjbboss9973
Жыл бұрын
Better to stay away from 5.3 😢😮
@glanzone
Жыл бұрын
Didn't show sh!t. Basically said download it and play with it.
@odstavec-900mm6
Жыл бұрын
Cura 5.3 writes "Unable to slice". Experimenting with settings, as well as choosing other printers and profiles, does not help. What could be the problem? Cura 5.3.0-alpha+xmas works without errors.
@hendrikjbboss9973
Жыл бұрын
Cura 5.3.0 DOES NOT work without errors. When I choose Creality-Ender-3-S1-Pro then Cura 5.3 gives a 0.4mm nozzle and this CANNOT BE CHANGED 😮😮
Пікірлер: 25