As a 3D-printing audio engineer myself, I much enjoyed watching your solution. Bravo!
@The-Weekend-Warrior
Жыл бұрын
Consider using heatset inserts in 3D printed parts for screws and use something like M3 screws in them for a much more secure hold. Screwing screws directly into PLA or ABS is not ideal.
@docphillips5153
11 ай бұрын
I think every engineer designs a little differently. In the broadcast end, shielding is very important. In that arena I use an off the shelf metal box with strain relief. I Like your box but I would add a screw bolster inside to strengthen corners as well as counter sink the screws. Keep up the good work, I'll stop by see what else you come up with. Never stop dreaming or revising.
@KLRCAT
Ай бұрын
What heat shrink is that? (diameter and ratio). I'm gonna use that to label all my cables without having to desolder 16 of them. I have a pair of Cat boxes, but might look at trying this to make my own. Recently just made a couple of Multicable reels (using Expandable Braided Sleeving). One was a 30m Optical HDMI and Cat6 reel (for PTZ cameras), and the other was a 30m 3 cable Cat6 reel for my XR18, one cable is for the "remote" port, the second is to use a Cat5 USB extender (so I can multitrack record), and the third is to use a Cat6 Audio Snake (so I can receive the Headphones out from the XR18, an Aux out for Livestream feed, a XLR in for a Talkback Mic and finally a feed for PC audio or music.
@arichindustries
Ай бұрын
Shrink tube is 1” and at least a 2:1 ratio
@NeKoOoLaS
6 ай бұрын
Nice job .. very good actually!👌 Which rj45 network connector is that part? From where did you get it?
@KLRCAT
Ай бұрын
Would the grounding be better or worse with a metal case? I don't have a 3D printer, so was thinking of just getting a couple Metal Case Enclosures for Guitar Effect Pedals and using those instead.
@arichindustries
Ай бұрын
As long as everything is shielded properly either would be fine 😁
@leonamsoares5462
7 ай бұрын
Can you tell me the model of the female RJ45 connector?
@NwVlad
3 ай бұрын
I found this on Amazon I think it is the same. Neutrik NE8FDV-Y110-B Ethercon D-Series 110 Punch Down
@Richard1977
Жыл бұрын
Nice project but I would have used balanced patch cable as its more flexible and thinner. Or standard microphone cable if i didn't have balanced patch cable in stock. And I would have used a big strain relief for the cable. As for the box you could have used Neutrik's D-size shells for ease of fabrication. Or a readily available box like a Hammond 1590A (if I am not mistaken). You took out your step drill so could have saved yourself the trouble of designing a custom box...
@arichindustries
Жыл бұрын
Balanced patch cable is how I’ll build my future ones. D sized shell cases actually won’t fit the punch down block of the Ethercon connector. That was my first attempt.
@Otakatikaja910
11 ай бұрын
That's great, it can save costs but what about sound quality? Is it quiet or is there still noise?
@arichindustries
11 ай бұрын
Very quiet, quality is just as good as any analog snake.
@Otakatikaja910
11 ай бұрын
@@arichindustries good 👍
@soundgineering4771
Жыл бұрын
wait, so each twisted pair on the Cat5, 6, or seven can create only one channel, right? What if we want to make 8 channels? Do we need to use two of those Ethercon connectors? great video.
@arichindustries
Жыл бұрын
Yes. 4 channel is max for one connector. You could easily make a bigger box with with 8 you would just have to run 2 cat cables out of it.
@glennwilson8560
4 ай бұрын
Do you have the file for the 3d print?
@The-Weekend-Warrior
Жыл бұрын
Ehh, the heat gun is an ugly solution. Use microphone cable for the XLRs and you'll spare yourself this whole shabang..... :)
@mrbenzinfo3119
Жыл бұрын
Can u show diagram connection xlr to ethercon?
@arichindustries
Жыл бұрын
The diagram can be found on the sound tools website.
@mrbenzinfo3119
Жыл бұрын
@@arichindustries link ?
@DJROSKO
11 ай бұрын
Link please
@The-Weekend-Warrior
Жыл бұрын
Why on earth would you use ethernet cable for the XLRs??? The purpose of the whole thing would be to use microphone cables for the XLRs that go into an Ethernet socket so that you can connect a long Cat 5/6/7 ethernet cable to the socket. There's zero need to use ethernet cable for the XLR portion of the build (it's too rigid, inconvenient and unnecessary). Nice job designing the enclosure iterations! Excellent idea otherwise!!! :D
@arichindustries
Жыл бұрын
Just what I had on hand to build a prototype. Microphone cable would 100% be better. 23 awg mic cable is too big to fit a punch down so you’d have to find some smaller.
@The-Weekend-Warrior
Жыл бұрын
@@arichindustries This is a super nice project otherwise, don't get me wrong, I just felt the ethernet cables were way too stiff to be working with. Not to mention that this kind is less flexible and more brittle on the long term than mic cable... on this cable length, you can definitely get away with thinner mic cable, especially if the connection is balanced when using shielded CAT5/6
@MorrisLiveProductions
Жыл бұрын
links to 3d print files please
@arichindustries
Жыл бұрын
Links coming soon!
@LorenzoHagenes-re1sr
Жыл бұрын
😪 'Promo SM'
@NwVlad
3 ай бұрын
Can you please tell me what RJ45 connector that is? I can not find one with a shield.
@mariap6329
2 ай бұрын
it's called ethercon but you can use a regular rj45 conector
Пікірлер: 31