Very nice angle on the video! I could see the crack moving and it definitely made all the difference in understanding the process!
@jamescarroll-dv4ty
10 ай бұрын
Once you start the run, turn over and apply pressure running it around, then flip back Make the relief cuts, works great, Thanks for the video, shows you know what you're doing!
@onlooker251
6 жыл бұрын
Nicely executed - concise instructions, thanks for sharing. John
@actionman22
8 жыл бұрын
Thanks for your video, gave me the confidence to get the job done. My 2mm thick circles didn't need to have the Crack opened both sides though and I found that splitting the offcut at one point and dropping the circle out in one go was the cleanest edge I could get. I don't think it would work so well for 3mm or thicker though.
@glassbeveller
8 жыл бұрын
actionman22 thicker glass gets much harder & yes 2mm is great to work with & you can get the circle to drop out with 1 side cut. Thanks for the comment 👍
@p8check
Жыл бұрын
I was cringing every Rome you drug your fingers along the cut lol
@glassbeveller
11 жыл бұрын
You can make a cut in the outer circle waste, open the cut , then flex the cut apart so the circle just drops out. But ! This is will work on thin glass but not very well on 5mm and thicker and if you try doing it on the thicker glass you will end up chipping the glass circle. But great trick for 3 mm thickness.
@BirdOfParadise777
12 жыл бұрын
Totally awesome! :) When it finally "splits", all the way through, around the center... why won't it just "fall" out? Thanks:) BOP
@glassbeveller
8 жыл бұрын
See my other videos. One of them covers that question on clear glass. But you may chip the mirror so follow the video , use plenty of kero & a nice steady even pressure on the curt
@Johnnyred51
11 жыл бұрын
Before removing the cut off, push down on the scribe which separates the cut completely. Then make one cut at the front and spread the cutoff causing the center piece to drop cleanly l.
@electrotsmishar
Жыл бұрын
super cool
@JT_India
Жыл бұрын
Thanks
@torribeard5947
Жыл бұрын
Nice video. I'd have to wear gloves.
@glassbeveller
Жыл бұрын
Believe it or not once you’ve been doing it for many years gloves are a pain. Required for safety & dangerous cutting & glazing jobs of course but if you (really) know what your doing it becomes optional in most cases . It becomes like working with wood 😂
@denisebetz7632
4 жыл бұрын
You make it look so easy!!
@RamonPayos
20 күн бұрын
How cut with frame
@F3YAW
11 ай бұрын
Thanks for the video.What can be substituted for karo
@glassbeveller
11 ай бұрын
WD40 , CRC any very thin lubricant 👍
@MarriedToTheKGB
Жыл бұрын
can you easily cut a circular hole in a car window? I want to put a stove in a camper conversion and would rather not cut a hole in the body. The windows are curved and not perfectly flat
@glassbeveller
Жыл бұрын
Curved glass has some tension in the glass so 80% chance of it breaking when cutting the hole. If it’s toughened / tempered glass it can’t be done ! Cheaper to get a clear polycarbonate sheet cut to size that can be flexed to a curve with a hole in. DONT use Perspex, curved glass with a hole ( min) $1,000 I hope that helps you out. 👍
@MarriedToTheKGB
Жыл бұрын
@@glassbeveller thanks. It looks like i'm gonna drill through the roof after all then
@misssummersalt
3 жыл бұрын
Thanks heaps Daz!
@baoluo1
3 жыл бұрын
Nice tutorial - thanks.
@vyvyienewalser6798
3 жыл бұрын
U make it look so easy
@glassbeveller
3 жыл бұрын
Thanks. 👍👍 When working with glass for years you have a respect for it but it just no longer feels like a dangerous medium. Hence no safety gear 😐 bit silly looking back
@user-ui4hd5tz3x
Жыл бұрын
Like you said a pro I ain't yet I'm convinced enough to try new thing ain't scard to fail. Don't hate lol
@ottomatic7823
Жыл бұрын
Okay, that's how you do it in the Southern Hemisphere but what about the Northern Hemisphere? 🙃
@dennisobrien3133
11 ай бұрын
Can you remove the circle piece ending with the intact square?
@glassbeveller
11 ай бұрын
So a cat for hole in a mirror? Yes . See my cat door video 👍👍
@dhorton51
4 жыл бұрын
Can you buy the ccircle contraption or did you makw it your self? Very good instructions! Thanks for sharing. Stay safe.
@TMBKTheLazyBee
3 жыл бұрын
Seems to be one of them bole circle cutters
@julialazydog1862
8 жыл бұрын
onya dazza, you're a champ!
@ivonneaburto7301
3 жыл бұрын
Guauuuuuuuuuuuuuuuuu. Congratulesions
@johnwurst6691
7 жыл бұрын
Great video! Thanks
@glassbeveller
7 жыл бұрын
John WURST thanks 👍
@heidismith6148
4 жыл бұрын
thanks, helps alot
@johnjwade
3 жыл бұрын
I'd like to know which cutter you use. I got one on amazon for cutting mirror and I cant seem to get a smooth circle cut no matter how much cutting fluid I use. Thanks in advance!
@glassbeveller
3 жыл бұрын
send me a picture of your cutter and I can advise 👍👍
@johnjwade
3 жыл бұрын
@@glassbeveller Do y o u have an email? Can't text overseas.
@glassbeveller
3 жыл бұрын
Yoyo TC 1 very good & used all day last months
@johnbarnes4998
6 жыл бұрын
Oops! Did I see you cut your finger at the end? I've been a glazier since 1978. Note: Leave only 1" of space between the circle edge and the outer edge. Makes it easier to remove the falloff.
@glassbeveller
6 жыл бұрын
John Barnes just a splinter. You know how it is . Ha ha 👍 have you ever had one travel under the skin & come out further up you hand at a much later date . I have 😝
@Justmyopinionlol
7 жыл бұрын
this demonstration is like a sensei kung fu master demonstration. Every move has reason and cause.
@glassbeveller
7 жыл бұрын
Justmyopinionlol thanks mate 😂
@abdou7926
4 жыл бұрын
Good job but no protection gloves people are watching and imitating
@glassbeveller
3 жыл бұрын
Glass is like wood to me, safe as but I was a bit younger then & glasses should always be worn.
Пікірлер: 48