Thank you for showing this. The galvanized pipe lever trick is a stroke of genius.
@cubmancan
2 жыл бұрын
Thanks for Watching!
@ragdadtx1835
Жыл бұрын
Thanks so much for your video. I had a similar project where I needed to cut 12 steel anchor bolts off a concrete patio to remove an old, rusted, wrought iron fence and gate. Local handyman was going to charge me $1000, yes 1K, not including concrete patching (if needed) or disposal. Went to Harbor Freight and spent $35.70 for the grinder and a pack of cutoff wheels. Took me about hour and a half, but was able get the job done after watching your video. Will probably never use the grinder again, but saved $964.30, so it's ok.
@cubmancan
Жыл бұрын
Glad it helped!
@tugga0318
2 жыл бұрын
Awesome video! Just ripped up a floor from an old Green house with these buggers there, i can now remove them away from my son running around and treading on them, thanks mate from Australia!
@cubmancan
2 жыл бұрын
Glad I could help!
@susanblackley7065
2 ай бұрын
Thank you!
@cubmancan
2 ай бұрын
Glad I could help!
@andrewvanyo4423
3 жыл бұрын
Thanks. Exactly what i was looking for
@cubmancan
3 жыл бұрын
Glad it Helped! Thanks for Watching!
@stratdad8218
3 жыл бұрын
I imagine a dremel tool with metal cutting wheel would suffice as well? Need to do this around my pool as well.
@jimscanlan7385
3 жыл бұрын
Great video. I had tried using a reciprocal saw, but as you said, it leaves a raised nub. . I borrowed a friends angle grinder today and thought I’d give KZitem and look before I started. This video was perfect
@cubmancan
3 жыл бұрын
Thanks very much!
@philphillips1810
5 ай бұрын
Excellent. Just the information I was looking for. Thanks. 😊
@cubmancan
5 ай бұрын
Glad it was helpful!
@david196609876
2 жыл бұрын
Thanks. I need to do this exact same thing.
@cubmancan
2 жыл бұрын
Thanks for watching!
@erodrig3
2 жыл бұрын
thanks this helped me!
@cubmancan
2 жыл бұрын
Glad it helped!
@Olivertwiztd
2 жыл бұрын
That looks so intense! Is there potential for all of those sparks to be dangerous in any way?
@cubmancan
2 жыл бұрын
This was an outdoor activity, so I had fewer concerns than if indoors. That said, ALWAYS wear eye protection when grinding any metals! And search the area and remove any nearby flammable materials before beginning the work, as a spark could start a fire in any kind of highly flammable material. In this case, I found the sparks to be very small, retaining heat for a very short duration and did not travel far from the grinding surfaces. ALWAYS be careful and wear appropriate protective gear and protect around the work area. Thanks for the question!
@MrDarren6868
2 жыл бұрын
Hi.. l got 4 bolts that's been drilled and filled with concrete glue, can l get it out without cutting it or would it be better to do it the way you just done .. Thanks
@cubmancan
2 жыл бұрын
I haven't done any glued in studs, but they would likely be trouble to attempt to extract. That epoxy is some hard material. I would think heating them may damage or weaken the concrete. I thought about cutting and drilling down the center of the studs before I did it this way. That seemed like WAY too much work, and likely would make for an ugly result. Thanks for the comment!
@yourwealthspecialist
Жыл бұрын
thank u sir - this did help me -
@cubmancan
Жыл бұрын
Good to hear! Thanks
@yourwealthspecialist
Жыл бұрын
@@cubmancan used my cordless sawsal and it worked like a champ - messed up a blade but got the job done - thanks for sharing and hope you have been enjoying your pool
@CCT.8B
3 жыл бұрын
Omg... thank you for making this video. I have some deck post I removed and found anchor bolts in the concrete. I have a Ryobi angle grinder. You mentioned a metal grinding wheel. Is there a specific type that will work better than others? Carbide? Diamond? Also, do you worry about the left over metal rusting? Any preventative measures for that little spot to not rust?
@cubmancan
3 жыл бұрын
Thanks for the Comment - and for Watching the video! 1- Depending on what type of grinder you have, something like this will work very well - Don't spend a lot of money on this, they grind pretty quickly: KSEIBI 651002 4-Inch by 1/4-Inch Metal Stainless Steel INOX Grinding Disc Depressed Center Grind Wheel, 5/8-Inch Arbor, 10-Pack / these are about $14 for 10 wheels - At Harbor Freight they are less than $3 each I am pretty sure. 2- Make sure you get the right "arbor" size and threads (the spindle that spins). If in doubt, take your grinder to the hardware store or Harbor Freight and match the wheel to your grinder. 3- Make sure you get wheels for grinding metal, not for masonry - it states that on the label on the disc. 4- I did not do anything on the "nub" left over to prevent rust, but may be a good idea - I think it will rust just superficially, but a dot of "Rustoleum" wouldn't hurt. If not now, it is easy to touch it later with the grinder and hit a dot of paint on it. Let me know if you discover anything not covered on the video - Thanks!
@littlsuprstr
2 жыл бұрын
I used a rigid brand diamond rim metal cutting wheel. It made short work out of the bolts.
Пікірлер: 31