OMG!!! THE FREAK’N JET NEEDLE!!! YOU JUST SAVED MY LIFE MAN!! I have been thru my carb a million times and I was ready to throw in the towel on the whole damn bike out of sheer frustration. There is no reason my Vulcan 1500 should be running so rich and crappy. I went through every single vacuum hose every single part of the carb, air box, air cleaners, compression checks, diaphragms, choke, throttle cables, tank vents, caps… you name it I checked it and cleaned it or replaced it. I never knew the needle jet was in there just like you stated! $50 mistake and I am glad to pay it but dagum.. not 1 single mention of this on any of the dozens of forum posts I read. THANK YOU SIR!!!!! YOU ARE THE MAN!!! A+++ video my man!
@2manysigns
9 жыл бұрын
Thank you very much for these highly professional perfect productions . Could not hoped for more ....... and free ! Highly valued ! I'm inspired :)
@83vf1100c
4 жыл бұрын
This is a very excellent video series! Refreshing in a “hey, what’s up KZitem?!” Environment!👍
@clarktferrill
10 жыл бұрын
This video is so good ..Thanks for putting it up...I learned so much that I hadn't thought of...thx
@jonathanharcelldaraucheman7935
3 жыл бұрын
Awesome step-by-step explanation. Thanks for it.
@cbCONCRETEPUMPER
3 жыл бұрын
I like to melt the plastic off a bread tie and use the wire. It's usually perfect size to stick through the tiny holes on pilot jets
@hobbiehobbs
10 жыл бұрын
Great video Thank You
@Inuktuuk
7 жыл бұрын
Thanks for posting.
@klrmoto
5 жыл бұрын
I took note of the amount of down force you used when removing the pilot jet. My screw driver did not fit fully down into the stock pilot jet slot. It only engaged half of the depth of the slot on the pilot jet. I did not use enough down force like you did and small pieces at the top of the jet at the slot sheared off. On my second attempt I used much more down force and it "snapped" loose. I matched up my screw driver to the jet and the screw driver did not fit fully down into the slot.
@starguy9
10 жыл бұрын
...satisfying
@TheAmilcarpapaleo
4 жыл бұрын
Thanks!!!!!
@muddieair
7 жыл бұрын
Great set of videos , I have a fuel seep( leak) around the float bowl. Do I have to remove the carb to replace the rubber gasket? Thanks
@JG-TV
4 жыл бұрын
Great vid! My jet needle is completely gone haha
@i240sxDRIFT
8 жыл бұрын
Is this the same carb that came on the Vulcan 800? Looking to buying one and have been doing lots of research on carbs as my current bike is efi just preparing to tinker with it lol thanks in advance great videos btw!
@gittyupalice96
4 жыл бұрын
few... You scared the crap out of me with the (silver) "jet needle" part at
@protectork9831
4 жыл бұрын
I put the metal parts in pure pine sole. 100 % . So when I remove the parts tomorrow do I need to wash the pine sol off with water
@march11stoneytony
9 жыл бұрын
Did you just use water to rinse off the pine sol? Would you suggest rinsing the body/jets etc in gasoline?
@clarktferrill
10 жыл бұрын
Harley has the diaphragm p/n 27535-88 as they use this same carb in the past..about half the price of Kaw.....do u agree?
@randygrindle5121
8 жыл бұрын
awssome looks like a good carb im going to buy a klr my fzr 1000is horrible i hate it always broke
@tibordhondt9264
4 жыл бұрын
i do have a long needle hanging on the bowl, you don't. should i remove it?
Пікірлер: 46