I took it a step further with my cordless impact wrench and blasted the fittings together in a matter of seconds. Works good if you got your impact gun and a socket set handy.
@Hydraulic.Online
3 жыл бұрын
Wow 6miler what a great idea. Just make sure not to over tighten the smaller fittings. 😉
@billclayton8127
3 жыл бұрын
Very informative video. A must see before attempting a high pressure hose repair. Thanks
@Hydraulic.Online
3 жыл бұрын
Glad it was helpful Bill and thanks for the feedback !😃 So what recent high pressure hose repairs have you attempted / Completed?
@jiayuanfittingchina5765
4 жыл бұрын
Wonderfull video for understanding assembly of reusable hose fittings. We know how to produce hose end and screw ferrule, with high quality, but it will help us to improve the function of hose assembly.
@Hydraulic.Online
4 жыл бұрын
Thanks for the comments and for watching our Video, We are flattered that a hose fitting manufacturer has watched and commented favourably.
@bicycleengineering
Жыл бұрын
Firstly great explanation. Ive just started in the hydraulic industry in Australia. Its amazing it doesn't leak though the hose tail threads. I know the tail pushed quite far in the hose but how deep are the threads?
@Hydraulic.Online
Жыл бұрын
Thanks for the feedback have a good look at these close up photos on our webstore, www.hydraulic.online/JIC-Female-Field-Fit-Reusable-Hose-Fittings-Straight-p449076511
@lifoterjames2328
3 жыл бұрын
Please this very informative. Which is that liquid that you are applying on that hose before scruing into the joints fitting
@Hydraulic.Online
3 жыл бұрын
We use a Good Quality Bearing Grease or Petroleum Jelly
@smca7271
7 ай бұрын
Ive bought (from you guys) and had great success for about 30 of these at 3/8".....but the last ones I bought 1/2" have leaked between the fitting and hose,on one hose only ,out of three (also a pin hole spray out of hose when dead headed,reliefs at 2000psi)....I redid the fitting and again leaks between fitting and hose (is the delivery hose from pump.....I know I'm not doing it wrong,could a faulty hose cause this,don't know what else to try....love your online shop,keep it going.
@Hydraulic.Online
6 ай бұрын
Thanks for the feedback about our Store Please make sure that you are using "new" SAE 100 R2 Specification hose with 2 wire bodies, and new SAE 100R1 Specification hose with a 1 wire body. A "2 wire body" will have two thin rings or grooves machined onto the neck and a "1 wire body" will have one ring or groove machined into its neck. Also we do not recommend that you use Old or used hose to make assemblies as the rubber may have perised with age, temperature, and prolonged contact with oil. You should have been given the opportunity to download assembly Instructions when you placed your order. Please let us know if you continue to have issues.
@bunndyboy
4 жыл бұрын
Hello guys would you have something to fix a hole in the hose on a high pressure water blaster? Great video.
@Hydraulic.Online
4 жыл бұрын
Hi Billy thanks for watching and your positive comments, we have a web store called hydraulic.online that sells the parts you will need to repair the hole in your water blaster hose. Depending on the type and size of hose you have this link will give you access to a variety of field fit reusable fittings as seen used and installed on this video. www.hydraulic.online/store/BSP-Reusable-Hydraulic-Hose-Fitting-Male-or-Female-p53195633
@bunndyboy
4 жыл бұрын
@@Hydraulic.Online thank you.
@adazhang
2 жыл бұрын
GOOD!
@Hydraulic.Online
Жыл бұрын
Thankyou for the feedback Ada
@jaluhu
Жыл бұрын
Good video
@Hydraulic.Online
Жыл бұрын
Thanks for the visit and the positive comment Jaluhu.
@marinetrax
2 жыл бұрын
Any idea when you will be getting the 10 mtr lenths Hydraulic Hose 1/2 Inch Two Wire Egmattec hoses in? You have GEN 10m Coil Hydraulic Hose SAE100R2AT 2 Wire but I am assuming that is not as good as quality?
@Hydraulic.Online
2 жыл бұрын
1/4 and 3/8 2 wire ENGMATTEC hose is back in stock, 1/2 and 3/4 Stock (maybe by end of MAY 2022), Please don't be concerned about the quality of the GEN Hose, we DO NOT Sell Poor Quality Products, all our Products are guaranteed to be meet or exceed the Stated SAE specifications.
@cevans7119
2 жыл бұрын
Just curious but under say 200bar from a pressure washer. Won't the end burst off at some point? Aren't swaging machines meant for this type of thing?
@Hydraulic.Online
2 жыл бұрын
The important thing to remember is that you use the hose fittings that are correctly matched to the hose, wether you use reusable fittings or swaging machines you have to make sure you are using matched sets. 200 bar (3000 psi) is fine for reusables as long as the hose is designed for that pressure and is still in good condition. The added flexibility with most swaging machines is that you can alter the crimp diameter to suit a range of different hose designs.
@danshouseofsmokeandoutdoor7119
3 жыл бұрын
Great video thanks
@Hydraulic.Online
3 жыл бұрын
Glad you enjoyed it
@hammothw4814
2 жыл бұрын
after it bottoms out, why back it off half a turn?
@Hydraulic.Online
Жыл бұрын
Gives the hose and the tail you screw into it some space for expansion
@christophercolumbus8944
3 жыл бұрын
i have a leak in my hydraulic line under the car line is about 1/2" diameter on the outside the pressure is very high and it's hot would you use fiberglass resin and sheet? ?
@Hydraulic.Online
3 жыл бұрын
Hello Christopher, Tell me more about the hydraulic line please, is it made from steel like a pipe or is it made from rubber like a hose. In either case fiberglass resin and sheet will more than likely not work. It sounds to me like it may be from your power steering system or possibly even part of a hydraulic suspension system. Both of these systems work at pressures from 1000 psi for power steering and up to 2000 PSI for hydraulic suspension. If it is a metal pipe you may be able to have a joiner put in it, if it is a hose then the hose will have to be replaced. Hope this helps.
@christophercolumbus8944
3 жыл бұрын
@@Hydraulic.Online yes exactly metal pipes i heard 3000 PSI too
@SusannaJu
4 жыл бұрын
it's wonderful. but a machine tool is much helpful.
@Hydraulic.Online
4 жыл бұрын
Yes you are correct, though when you in a machine out in the field, far from a workshop or service vehicle and mostly alone with just some basic tools and these cost effective field fit reusable hose fittings, in just 10 to 20 minutes and you are up and operating again.
@martinamadsen812
2 жыл бұрын
Good video, pity about the dreadfull backing music.🤔
@Hydraulic.Online
Жыл бұрын
yes music is a personal thing, ok but have you read that "You can't please all the people all of the time".
@pajeeper420
5 жыл бұрын
Good video. What kind of grease are you using on the threads?
@Hydraulic.Online
4 жыл бұрын
You can use heavy duty bearing grease, rubber grease or petroleum jelly as well as hydraulic oil just make sure it is clean and contaminant free.
@michellewang1284
4 жыл бұрын
Metric. BSP,and Us
@theotheronetoknow5828
2 жыл бұрын
Hi, how to get the hose on a reusable fitting that doesn't come apart, is one piece?
@Hydraulic.Online
Жыл бұрын
You can dismantle some crimp on fittings by carefully cutting off the shell, but you will need to recrimp a new shell onto the tail (if the tail is not damaged)
@victorvic1060
5 жыл бұрын
Hello I wanted a tip before making my order in your site, I have plans to manufacture a mini excavator with a maximum pressure of 200 bar. my cylinders have a piston diameter of 70 and two others of 80 in diameter. I have a double pump 16 + 11 cc 1500 turn, so I wanted to buy double braided hose and I do not know which to choose. thank you for your attention
@Hydraulic.Online
5 жыл бұрын
Hi Victor, Sorry for the delay in getting back to you. For the 11cc pump at that speed you'll be getting 16.5Lpm/4.2~Gpm and either 3/8" or 1/2" two wire hose will suit the application, for the 16cc pump you'll be getting 24Lpm/6Gpm for which 1/2" two wire will suit the application. Please let us know if you have any other questions. Cheers, Riley @ Hydraulic.Online
@victorvic1060
5 жыл бұрын
@@Hydraulic.Online. hello thank you for your answer. I also wanted to know which reusable pipe fittings I can use for crimping as on video. for you showed me in your site? thank you
@yoni703
Жыл бұрын
Is this to fix temporarily on field?
@Hydraulic.Online
Жыл бұрын
Yonimile you can use these fittings to make temporary repairs in the field to keep you going until such time you can replace the old hose with a new one. It also depends on the condition of the hose as well because if the hose is still in good condition you can leave it on permanently. Many people purchase a few of these fittings and a length of hose from us so that they can make their own hoses without needing a hydraulic hose crimper. Please also note that in Australia these fittings are not allowed to be used on mine sites.
@job38four10
2 жыл бұрын
But I dont even what size hydraulic fittings are on my tractor, I have a great idea find a L3400 and replace a FEL hose on video so I know what to get...........
@Hydraulic.Online
2 жыл бұрын
Great point! Please watch this video it may help you identify your hose fittings kzitem.info/news/bejne/xJ-Qlnl6hZ56nKA The LM3400 tractor is made by Kubota and Kubota generally manufacture their hydraulic hoses with British Standard Threads (BSP)
@joachimgschwendtner9251
5 ай бұрын
Wat is the name der fittigs
@Hydraulic.Online
4 ай бұрын
JIC Reusable Hydraulic Hose Fittings for 1/2 inch SAE 100R2 two wire Hose with 3/4 JIC Female Swivel Nut.
@SusanaSanchez-pe6xc
2 жыл бұрын
pls pm where to order re-usable fittings . many thnks
@Hydraulic.Online
2 жыл бұрын
If you are in Australia and looking for Reusable Hose Fittings click here: bit.ly/33a63fw If you are in the U.S. and are looking for Reusable Hose fittings click here: bit.ly/3F2kijS
@Hydraulic.Online
2 жыл бұрын
If you are in or near Australia and looking for Reusable Hose Fittings click here: bit.ly/33a63fw If you are in or near the United States and are looking for Reusable Hose fittings click here: bit.ly/3F2kijS
@lifoterjames2328
3 жыл бұрын
Please can I have your website or email address? I work with a road construction company and hydraulic hose breakage is one our major problems.
@Hydraulic.Online
3 жыл бұрын
*James* our web address to our online store is www.hydraulic.online/ Full contact details are on the website. Some useful links for Reusable Hose Fittings bit.ly/3lwAJPt and for Hydraulic Hose bit.ly/3fuVlni
@sureshmundargi2807
3 жыл бұрын
You have not used crimping tool. You mean Without crimping will it withstand 4000 psi?
@Hydraulic.Online
3 жыл бұрын
Yes... if you watch to the end of the video we actually test the hose assembly to 4000 PSI.
@bratvlad
Жыл бұрын
Paint hose repair
@Hydraulic.Online
Жыл бұрын
No sorry not with these reusable fittings, paint hoses require crimp on fittings.
@michellewang1284
5 жыл бұрын
we are factory of hose fitting. if u looking for factory of hydraulic fiting, pls feel free to contact us.
@Hydraulic.Online
4 жыл бұрын
Thanks for watching our video Michelle, please send your catalog of fittings to our email address sales@mhfgc.com.au
@michellewang1284
4 жыл бұрын
@@Hydraulic.Online ok
@nkpstido9410
4 жыл бұрын
Aap apna contect numbar dijiyega boss
@Hydraulic.Online
4 жыл бұрын
Ranjan thanks for your email, our best contact is by email sales@mhfgc.com.au thanks for watching our video.
@Hydraulic.Online
3 жыл бұрын
If you are an Aussie and looking for Reusable Hose Fittings click here: bit.ly/33a63fw If you are in the U.S. and are looking for Reusable Hose fittings click here: bit.ly/3F2kijS
@communityfish9803
4 жыл бұрын
Please tell me this is a joke. If not The single WORST hose Assembly And test process EVER! Not to mention the shockingly bad safety practises of holding a pressurised hose in ur hands. I hope you have top grade employee health insurance. Strongly advise you get some professional training and equipment. Think I will download this and include it in my what not to do training.
@Hydraulic.Online
4 жыл бұрын
Thanks for watching our Video in its entirety and for the "constructive" comments Community Fish, BTW is this the tactic you employ to get other You tubers to watch your videos and to comment on them?
@communityfish9803
4 жыл бұрын
HYDRAULIC.ONLINE GOLD COAST your very welcome if you need some hose assembly pointers and training sure I can point you in the right direction. BTW as u can see from my channel I’m am not interested or serious in uploading videos or gaining views by my lack of content especially given any content I have uploaded is irrelevant to ur videos or industry. I am however an industry expert in Hydraulic hose manufacturing/assembly/testing and site services. The fact is Sir you are a business with terrible safe systems of work and skills.
@smca7271
7 ай бұрын
Energy source is hand pump,dont think you know anything about work health and saftey
Пікірлер: 72