Best vid ever! bloody simple and straight forward!
@bkt2009
11 ай бұрын
worked like a charm
@CenturionSystems
11 жыл бұрын
It's a pleasure! Glad we could be of assistance.
@michaelcook1627
10 жыл бұрын
thanks for the Vid guys, got my new remotes programmed quickly and easily after watching this.
@dragonballz2889
7 ай бұрын
our gate used to open by pressing once...then press again to stop for peds...then press to close...or press once to open full then press once to close full.....now i have to press twice.....how to set it back to once?????and what is time bar yes or no actually mean????
@clifton4th
3 жыл бұрын
So what is the problem if there is no beep when I press the remote button? Tried with multiple remotes an none will program?
@amponsahemmanuel7170
5 ай бұрын
When it says on limits set
@benportelli8705
11 жыл бұрын
hey, i have recently had one of these installed to replace my last, is it possible to learn in an old after market remote that isn't centurion because i would like to have one permanently in the car and one on my keys? thanks
@marioteixeira7699
9 жыл бұрын
Thank you for the video, i was successful in adding two remotes.
@CenturionSystems
9 жыл бұрын
Thanks for the feedback, Mario. Glad we could help.
@jabungcobo2879
4 күн бұрын
How to clear menu locked for remote control
@heinrichjemane7970
3 жыл бұрын
Doesn't acknowledge my new ET remote. I'm stuck.
@SolarEclipse777
Жыл бұрын
I have used exactly the above procedure at least 50 times to encode remotes into the D5 motor at our complex. Last month a contractor replaced the D5 with a new one. Now, despite following the above procedure, the controller does not respond to an input from a number of remotes with fresh batteries. Has the system been blocked by the contractor so that we have to pay him a call-out fee to encode remotes in future? If so, how can I unlock it?
@pantoffelslippers
Жыл бұрын
Gate doesn’t respond. I’m same 4 button green remote, looks like a Nova. Just want to use another button. Any difference in programming the green remotes?
@oliviaferreira9669
2 жыл бұрын
Hi, I want to program / learn in a remote, however at the remotes section it says it is TX locked, how do I get out of that?
@greylourie2096
Жыл бұрын
Please can you help me to delete a remote control from the D5 centurion gate motor? I use the NOVA remote controls. Thank you.
@andyt5199
7 жыл бұрын
Easy and simple thanks for the vid :)
@CenturionSystems
7 жыл бұрын
That's what we like to hear! We are really glad that the video helped.
@tshepomosesane8568
5 жыл бұрын
Hi I have an existing sherlo remote working on my d5, but I'm unable to add another sherlo remote, when I get to add remote by pressing the button, the d5 does not pick up the new remote. Please assist
@gigabyteaopen
11 жыл бұрын
Thank you for the help
@user-py2nj7qs2g
Жыл бұрын
I ask if u cancel the remote
@hdmeyer6535
4 жыл бұрын
Hi, How do I learn a Wireless Smartguard to the Evo gate motor?
@jeevannepali9334
2 жыл бұрын
Hi. Can I buy different brand and set up? Or it should be the same brand ?
@mogesgiorgis2854
5 жыл бұрын
Hi I see your video and I did the same to coding my new remote but it is not working please help.my remote is four button.
@chrisfurh
7 жыл бұрын
@CenturionSystems We've got two gates on our property. I have tried to pair a new remote with the one motor but now one button press opens both gates. Is there any way I can reset the Remote so I can learn it to open only one of the gates? Both gatemotors are D5 Evo's. Thanks
@CenturionSystems
7 жыл бұрын
Hi there. Please give us a call on +27 11 699 2400 or drop us a mail at support@centsys.co.za. Our friendly technical support team would be happy to assist you with your query.
@tysonred507
9 жыл бұрын
My sherlo remote isn't picked up when trying to set it on my centurion motor? I get to the point where it says press remote but it never beeps in acknowledgment. I know sherlo remotes can be programmed as every other remote at our house is sherlo. Please help!
@CenturionSystems
9 жыл бұрын
Gaz Mitraz Hi there. Thanks for your enquiry. The CENTURION onboard receiver in the D5-Evo will definitely only accept CENTURION's Nova remote controls. If other aftermarket remotes are being used in the system then the installer would have most likely added an aftermarket receiver that will accept those remotes. You will not be able to learn in non-CENTURION remotes to the controller.
@tomomofokeng9066
7 жыл бұрын
thank you safed me money .keep up
@sihlenyakane6792
6 ай бұрын
Mine keeps give me a "Error button already assigned" error
@Annie8005
10 жыл бұрын
I have tried and get all the way to the part where you press the remote button but nothing happens. Just says: press remote button...nothing happens
@CenturionSystems
10 жыл бұрын
Hi there. Make sure you are using a Centurion Nova remote. Then ensure the remote control battery is still powered (check that the LED light remains on when you press and hold the button down - a flashing LED shows you the battery is low). If the receiver is ready to learn in a remote then it will beep twice to acknowledge that the remote has been received.
@letlhogonologumede503
8 жыл бұрын
when I try to set gate opening limits,after the massage 'clear the gate path'.the screen will switch off after confirmation.sometimes it will move a bit n restart on the screen.what mite be a problem
@CenturionSystems
8 жыл бұрын
+lettor gumede Hi there. If the controller is switching off and then back on this is a sign that the battery does not have enough power to run the gate. It will most likely have sufficient power to keep the controller alive but as soon as the motor draws more power the voltage drops and that is the reset you're observing. Please try and replace your battery and ensure that it is being charged (by making sure that the gate motor has power connected to it).
@JessicaSmith-jq8kd
8 жыл бұрын
Please help, all the buttons but the centre button seems to work. Can it be disabled/ enabled?
@CenturionSystems
8 жыл бұрын
+Jessica Smith Apologies for the lengthily delay in replying to you. Yes, the round test button may be disabled (and enabled again) in Menu 10, General Features of the controller. Sub-menu 10.4 allows you to enable/disable it.
@JessicaSmith-jq8kd
8 жыл бұрын
+CenturionSystems Thanks for the reply, so if it's disabled, how do I access the menu? Sorry, not super familiar with the system.
@CenturionSystems
8 жыл бұрын
+Jessica Smith When the round 'test' button is set to be disabled, it is only disabled so that the gate cannot be triggered to run by pressing the button. All programming is still possible. However, re-looking at the comment it appears that you referred to the oblong button - sorry, I should have picked that up sooner. The oblong button cannot be disabled and if it is not responding then the controller has developed a fault. This can be caused by water ingress - and some other causes too. Please check the cover of the motor to ensure that there are no cracks visible (look from the underside). If you're still battling please call our Tech Support Call Centre on +27 11 699 2481 for assistance so that we can arrange to have this resolved for you.
@JessicaSmith-jq8kd
8 жыл бұрын
+CenturionSystems Thanks for the reply, did mean the oblong button. Will call your tech department, thanks again!
@innocentngomjua2244
9 жыл бұрын
I installed a D5-Evo 500kg load weight limit at a clien'ts gate and it started functioning well but later stopped and was making a bipping noise and projected on the dash board baust fault, what should I do next for it to start function well again, I must equally say that the gate handles more than 2000 vehicles per day and functions 24/24
@CenturionSystems
9 жыл бұрын
Innocent Ngom Jua Hi there. The D5-Evo is designed to handle a maximum of 150 operations per day, and thus it is being utilised way beyond its specification. What has probably happened, is that either the brushes have worn or the battery has been completely drained. Please contact our technical support team on +27 699 2400 for a more detailed diagnosis, but I would recommend installing a heavy-duty gate motor such as the A10 to handle the large traffic volumes.
@innocentngomjua2244
9 жыл бұрын
Thanks for the respond, there was a mistake in a fault specification, i wrote baust fault rather it is DOSS FAULT
@Rochingas
7 жыл бұрын
How often do you use this control?
@jonandrews3685
Жыл бұрын
I followed your steps but when it says press remote & I press it nothing happens and the remote battery is new I even tried a factory reset 😴
@iniobongessien7926
7 жыл бұрын
Please how can I program my car's homelink remote control to operate the D5-Evo?
@CenturionSystems
7 жыл бұрын
Hi there. Regrettably, that will not be possible. Since the D5-Evo's onboard receiver is a NOVA code-hopping module, it is only compatible withe blue and gray CENTURION NOVA remotes.
@iniobongessien7926
7 жыл бұрын
Thanks. I figured so.
@raf78932
7 жыл бұрын
how can I add 3 button grey remote on d5 evo centurian gate motor?
@CenturionSystems
7 жыл бұрын
Hi Rafi. Please give our technical support team a call on +27 11 699 2481 or send us an email at support@centsys.co.za. A technician will be assigned to attend to your query.
@theglowproject
4 жыл бұрын
I cleared/deleted all remotes then added a new one. But when I want to operate the remote nothing happens, just beeps and the Trg light goes red. I have tried over and over again with no luck
@shersandrews
9 жыл бұрын
When I hold in the center button for two seconds and enter into settings, it does give me the remote option. The motor could possible by a different model but has the same layout. Could you please kindly assist me with this matter
@CenturionSystems
9 жыл бұрын
Sherwin Andrews The Remote Controls option will definitely be there. You need to scroll to the menu section "11. Remote Controls". If you still can't find it please call our Technical Support Call Centre on +27 11 699 2481 and they can talk you through the process.
@user-py2nj7qs2g
Жыл бұрын
If u cancel remote
@kooscoetzee1185
8 жыл бұрын
My gate are open and close the hole time HELP PLEASE
@CenturionSystems
8 жыл бұрын
+koos coetzee There must be something triggering your gate for it to open. Often when it appears to be doing this 'by itself' it's actually a neighbour's remote control that has been learned in to the gate motor accidentally during the installation. The first step would be to delete the remotes and ensure that only your's are learned in. Please give our Tech Support Team a call on 011 699 2481 if you require further assistance.
@vanessavandermerwe9343
8 жыл бұрын
All's well you can programme for a myriad of options, open the gate, yes, now closing it... snag. Stop the gate... snag. Installers are not as helpful as the originator of this product.
@matthewhoward1291
2 жыл бұрын
Why doesn't this work for other remotes other than Centurion? It seems like a major design flaw. The gate motor didn't even come with remotes. Smells like a money making scheme.
Пікірлер: 57