KZ
item
Негізгі бет
Трендинг
Журнал
Ұнаған бейнелер
Ең жақсы KZitem
Фильм және анимация
Автокөліктер мен көлік құралдары
Музыка
Үй жануарлары мен аңдар
Спорт
Ойындар
Комедия
Ойын-сауық
Тәжірибелік нұсқаулар және стиль
Ғылым және технология
Кіру
Тіркелу
Кіру
Тіркелу
Негізгі бет
Трендинг
Журнал
Ұнаған бейнелер
Ең жақсы KZitem
Фильм және анимация
Автокөліктер мен көлік құралдары
Музыка
Үй жануарлары мен аңдар
Спорт
Ойындар
Комедия
Ойын-сауық
Тәжірибелік нұсқаулар және стиль
Ғылым және технология
Негізгі бет
Darton LS Sleeve Installation part 2
Күн бұрын
Darton LS Sleeve Installation part 2
Рет қаралды
7,343
Wolverine Engines
1
1
Жүктеу
Пікірлер: 18
@TurboDog73TX
8 ай бұрын
I'd never seen this process done start to finish. Thank You for sharing it with us!
@GrandPitoVic
Жыл бұрын
Brother, I'd like to see the other sleeves as well. This was very interesting.
@holydiver9090
8 ай бұрын
Без мастера знающего как нужно все сделать ничего не получится. Отличная работа.
@PontiacLS
2 күн бұрын
You have removed all of the structure of the block it no longer has strength in the walls. Or am I missing something here.. Please explain
@christophergriffin8344
8 ай бұрын
Getting it on proper🤘 Very nice job.
@jkdwayne
9 ай бұрын
Fabricate a pulling plate to pull the sleeves in with the studs. Ive seen them with locators that go in the bores and dowels.
@DanNaylor-tu1zl
3 ай бұрын
Did you make the block to 4th axis plate? We have the same Haas VF4
@brentlamb4881
5 ай бұрын
What boring head are you using?
@MichaelScudder72
3 ай бұрын
MID?
@logancarter2134
9 ай бұрын
I can't believe you are hammering those in on your expensive AND sensitive milling machine????
@Airman..
Жыл бұрын
Nicely done ✔️
@wolverineengines6156
Жыл бұрын
Thanks
@333pg333
10 ай бұрын
Have you had any issues with these MiD sleeves? Seems as if there are stories about failed motors using these sleeves.
@wolverineengines6156
9 ай бұрын
Have to run front and rear engine plates and not motor mounts or the block will twist!
@333pg333
9 ай бұрын
@@wolverineengines6156 What about with an inline 4 cylinder motor rather than big V8? hp will be in the 6-700hp region.
@JosephDAndrea0121
Жыл бұрын
Can you run a wet sleeve setup without a motor plate?
@wolverineengines6156
Жыл бұрын
Nope. You have to go to a dry sleeve. Can still get the 427/434 cubic inch build out of it.
@stampcollector7412
Жыл бұрын
@wolverineengines6156 Thanks, I've been told 700 is the safe limit of the ls7 how far can I take it dry sleeved?
Пікірлер: 18