Ayeee I see that 407 transponder. Ontario Represent! Great informative video. Thanks!
@jackt6112
8 жыл бұрын
"Dave's inverter had a fuse inside so he didn't require an inline one on his wiring" Oh yes he does require a fuse. The fuse protects the wiring. If anything pinches that wire to ground, the wire glows red hot and probably blow your battery while the fuse inside of the inverter will remain unaffected. The fuse inside of the inverter protects the inside of the inverter, just as the fuse inside of the radio protects the radio. I like the template idea.
@timmyeyre
10 жыл бұрын
just a little note to any DIY enthusiasts in regards to cars, beware if your working on your a pillar or passenger dash if there are airbags. I use the gentle tuck method dave used on the roof liner if they're fitted. Aside from that, nice mod and don't fret so much about electricity, that's what circuit breakers are for. lol
@LukeLucasCountry
5 жыл бұрын
Thanks. One of the best how to videos I've seen!
@TDF0907
10 жыл бұрын
Onboard fuse or not any wire tied to the battery should be fused within 1 foot of the battery. If that wire shorts anywhere on the way to the inverter the result will likely be a fire
@TimeHopeFaith
11 жыл бұрын
The 120 Volt socket is probably what I'd really want. :) Thanks for the video. :)
@AWSum-uf4ri
3 жыл бұрын
Thanks Dave. Super cool of you boss
@stevemoody6928
10 жыл бұрын
Good use of the Wilhelm Scream
@premisedrive2954
5 жыл бұрын
Wow! That's really impressive! How much do you charge for this service?
@queenbabycat369
5 жыл бұрын
Nice vid , pretty professional
@MN-pu6qx
8 жыл бұрын
Excellent job - well done.
@colinmaharaj
4 жыл бұрын
I was upstairs on a balcony with some family and there was a power line line 20 ft away and lightening hit it. I was temporarily blinded and deaf for a few minutes.
@happiehippie9268
9 жыл бұрын
Amazing! Nicely done..
@williambhoneycut5649
8 жыл бұрын
good video,you said cut out holes,what holes?,what did you measure to get holes?,you didnt show that part?
@assetxray9782
8 жыл бұрын
Dave, what gauge wire did you use from the Battery? (10, 12, or 14 Gage?) If 14, could you use Romex (house wiring with rubber sheath)?
@wilsonbrooks8447
5 жыл бұрын
Good knowledge
@eldms24
6 жыл бұрын
when you removed the outlet plugs from the inverter is the wiring shown in the video at 6:42 the original wiring straight from inside the inverter? or did you had to add the wiring to them?? if so how to confirm you used the colored wires to connect the wiring of the outlet plugs back where they were original connected inside the inverter?
@burntkat
6 жыл бұрын
?Dave's inverter may have a fuse inside of it, but there is still a requirement for one on the wire at the battery- unless you want to burn the car down.
@p47thunderbolt68
6 жыл бұрын
I have a 2000 watt, but it didn't come with normal 110v receptacle. It has a place that looks like one can be installed. What do I need go get? It did have a SUB.
@ElectronicFix
10 жыл бұрын
Pretty cool thanks
@reggiedsouza3896
8 жыл бұрын
love it!
@euroamericabusiness
10 жыл бұрын
Can you let me know what was the other sketch program you had used besides sketchup...? I can't really understand the name you mentioned on your video...! Thanks in advance
@davidhanselmann8148
10 жыл бұрын
I just found it. I couldn't really understand the video either. www.solidworks.com/
@davidhanselmann8148
10 жыл бұрын
I'm guessing he used this one. ??? www.3ds.com/products-services/draftsight/download-draftsight/#xtor=AD-508-[swfreetools]-[middle]-[intext]-[www.solidworks.com]
@edwardvasquez3962
11 жыл бұрын
I sure hope you dont spill a drink on the 120v socket, there is no GFCI outlet. You will find him with the headlines "Officer Finds Electrocuted Man In Single Car Accident" Not the best place to put 110-120V 15-20amp plug.
@burntkat
6 жыл бұрын
Bondo isn't structural. A MUCH better option is JB Weld, and easier to work with as well.
@djrudy9833
9 жыл бұрын
I wldnt worry abt liquid causing a short, u might drop change in there by accident, or take that change an buy a cple rubber caps for the 12 volt power outlets. Or add a rocker switch so u can turn them off an on just like u did with ur inverter. Good ideas u have, not crazy about the quality of materials u used. An u didn't have to destroy ur inverter, panel mount outlets on amazon r what u destroyed the inverter to get! 2 bux each or so
@jptravers
11 жыл бұрын
Excellent
@Virtuewz
9 жыл бұрын
could you possible use speaker wire instead of regular wire?
@nightstringers
7 жыл бұрын
NO it would fry cant handle amps. needed
@rockoilcolonel
7 жыл бұрын
The inverter uses power even when no 120VAC devices are plugged in. It would have been better to add a on/off switch for AC power.
@jtorres93
7 жыл бұрын
He did. That's what the "AC" button was for.
@mikamo
6 жыл бұрын
6:56 is that the heat sink? Don’t you, like, kind of need that? Y’know, for the heat?
@nightstringers
7 жыл бұрын
I would have just plug a power cord into the inverter and cut the female plug off the other end and soldered the wire to the panel plug. forget fuses 12 volt circuit work great .. I have had 100 amp fuse holder melt even when I'm not drawing a lot
@99beta
9 жыл бұрын
I have a Scion IQ and the USB I Pod interface does not do USB charging. Time to do some hacking.
@AtarRoux
10 жыл бұрын
400 watts? im pretty sure Toyotas come with 120 volt plugs
@AtarRoux
9 жыл бұрын
sounds right. thanks :)
@nightstringers
7 жыл бұрын
I would NEVER use a cig lighter socket the wire on those are way to fine cant really handle a load . In my day I have bought the cig lighter socket and wired it with heavy duty gage wire
@justinwbohner
5 жыл бұрын
Looks like a good way to torch your truck. I spotted your mistakes and will be making changes. Otherwise the video is good.
@eglesbucs
6 жыл бұрын
why didnt he show how to do the wiring?
@robbrown6495
9 жыл бұрын
Cannot understand why you think a mains power outlet is essential in a car?
@christiansandoval8139
8 жыл бұрын
it's very useful for road trips charging laptops camping
@nightstringers
7 жыл бұрын
I need it for work video production . I also use it for coffee maker and frying pan when I'm on a road trip
@mikamo
6 жыл бұрын
In addition to everybody else’s comments, how else would I power my limited edition 1996 Boba Fett Nightlight For Small Frightened Children in my Subaru?!
@greg197107
10 жыл бұрын
great idea but really bad place
@ksmobile1
5 жыл бұрын
Music louder than narrator is really annoying there for thumbs down and shutting this thing off. Choice of music sucks as well.
Пікірлер: 49