Now do 25 oil changes a day to make your day. Then get yelled at when you miss a recommendation.
@TheHAMR1111
7 жыл бұрын
He's a world class tech and he tightens the oil filter with the wrench
@Drew-wf7vw
6 жыл бұрын
Looked a little awkward to do it by hand where it was located, he did specify "just make it snug" I don't see where your issue is
@tigergreg8
6 жыл бұрын
I agree Ice 100% If that filter were to leak because of hand tightening in that position, THEN, he wouldn't be considered a world class tech.
@alfonz0010
5 жыл бұрын
@@tigergreg8 my g8 and avalanche have same filter location. You don't need a oil wrench for tightening.
@maximagmhondafan8892
5 жыл бұрын
I hand tighten oil filters and I only had one customer come back because of that. On a damn Jeep Liberty were the oil filters are close to impossible to reach.
@jamesellis33
5 жыл бұрын
@@alfonz0010 you have just been lucky that is it.
@alexpetrie4508
7 жыл бұрын
That supervisor is like, "damn faster kid"
@markkukowski3710
4 жыл бұрын
Wow! So first, you have to find the vehicle on the lot, put it on the lift properly (Don't blow a tire - they tend to not like that), set up the lift in the correct spots, reset the oil life monitor, put an updated oil sticker on the window. Check wipers, lights, horn and e-brake. Then, go to computer and log onto the job. Open hood: Check belts, hoses, filters (which are not easy to get to these days), fluid levels, etc. Then, lift up: Drain oil and try to remove filter (because Hercules put it on). Go to parts department - Wait till they get done doing what they're doing: Give them your RO and get the parts.Come back and install the filter. Check all suspension, tires, cooler lines and pipes, check all components for leaks. Then pull wheels, check brakes, rotate tires. Write down all the specs in the multi-point program. Lower vehicle. Fill with oil. Then, go to the computer and write your story for the work you've done and if you found anything, go to parts: Wait your turn again: Get prices and then go back to your computer and get labor times: Give to your service writer who is too busy to talk to you. Wait till he comes out and says "They declined the work you recommended". Then you relearn the tire sensors, punch off the RO. Finnish the multi-point indicating that the customer declined the work. Then, double check the drain plug (because you forgot if you tightened it). Pull the vehicle out an start the next job.Collect your 0.4 of an hour pay for the 1.0 hour you just spent on the job. Piece of cake! I freekin love my job -
@ADDMEONPSN
4 жыл бұрын
Straight Bullshit I get .2 hours for all that at Midas
@ryans413
2 жыл бұрын
My first car I learned so much just working on it and yes it’s rewarding to fix something with your hands and get the car running again. When you have the whole engine apart and then put it all back together and the first turn of the key and it starts is hella rewarding. All this long hours those tough nights to get to that point where it turns over and runs even better then before is such a great conference boost.
@arthursmith643
6 жыл бұрын
Hand tight only on the oil filter. The wrench is not needed to get it tight enough. Make sure the old seal comes off with the old filter. Some guys use that wrench and crush the new seal and it will start leaking.
@lar4305
7 жыл бұрын
Wow! a white t shirt and not one single oil spot on it after he was done? He went belly on the floor to set the lift and no dirt on him. hahahaha.
@marybetheby5184
5 жыл бұрын
lar4305 TV magic =fake!!
@marioiacolucci
5 жыл бұрын
He did good!😁
@davidcampbell1899
4 жыл бұрын
Yea! That was my first clew this guy have never worked on a car, never owned an old shit box while stuggling to get through university. (spoiled little rich kid)
@deityreefer6617
3 жыл бұрын
The added noise in the background was gonna kill me
@Javi_quinty
2 жыл бұрын
I wanted to be a technician right after high school at my old job and my manager ruined that and I wasn’t sure if that’s what I want. But now I’m getting a new job doing oil changes and other automotive duties and I think this is a sign that there’s a second chance for anything
@cat-lw6kq
6 жыл бұрын
you have to like working with your hands, I used to do all of my won work with the help of a friend and my full time job was a tech at AT&T where I did wire wrap and soldering, if you like working with your hands ok, otherwise just be another office worker.
@marioiacolucci
5 жыл бұрын
He did good!
@LiftedSilveradoBuild
7 жыл бұрын
Annnnnnnd I stopped watching after he was advised to tighten the oil filter with the filter wrench.... Embarrassing and makes all of us look bad.
@moparmania86
7 жыл бұрын
With that engine you kinda have to because there isn't room to get your hand around the filter to get it tight enough. Otherwise I would agree. Usually that's not something you wanna do.
@Mhutch405
7 жыл бұрын
Lifted Silverado Build ohhh shut up
@JoeFpoc
7 жыл бұрын
ive been a mechanic for many years and for some reason when ever we get a oil change that previously had a oil change a dealer you know your in for a fight with the oil filter, they always seem to make them as tight as possible for some reason.
@thatmechanicguy8773
7 жыл бұрын
JOE FPOC, and literally almost every vehicle I've seen come from an independent has been hacked together, misdiagnosed, or not fixed properly. Are we really going to go down this road? The Chevrolet truck engine oil filters are almost impossible to tighten or loosen by hand because of the design that of the oil pan.
@JoeFpoc
7 жыл бұрын
Sheesh you are a angry tech to get mad at that comment. I also won't get into how we get vehicles all the time from dealerships where they told the customer they needed thousands in repair when they didn't. All mechanics suck
@ridds777
5 жыл бұрын
Warranty time.. Talk about that..
@guicefat
4 жыл бұрын
🤮
@PaggiPlumbing
4 жыл бұрын
Love the background shop noises lmao 🤣
@howtobasickid3991
3 жыл бұрын
Same man love it
@olenaerhardt7725
3 жыл бұрын
You need to wear gloves, to put a fresh (not old) oil on the gasket of the oil filter, and handtighten the filter as many commented before. I wouldn't make any jokes about that work, too much responsibilities there, any mistakes are dangerous. I think the work of a technician, it is like a walk on the rope. God Bless.
@robertmclaugh
7 жыл бұрын
at 2:41 wheres your saftey goggles? cmom maaan
@Nathan-cv6sm
6 жыл бұрын
Rob McLaughlin who wears glasses when changing oil? Gotta be pretty special to fuck that up...
@Xixu.co.6
5 жыл бұрын
Safety goggles lmao
@ryancourtney8607
5 жыл бұрын
@@Nathan-cv6sm I went to a chevy dealership for a while and left after 6 months because of all the sagety regulations you have to wear goggles all the time pretty stupid
@fuckjewtube69
5 жыл бұрын
@@Nathan-cv6sm Because a piece of rust can fall in your eye and get imbedded in your cornea and they have to dig it out and it will cause an eye ulcer which literally feels like having a piece of glass in your eyeball and you wont be sleeping for 5 days straight. Ask me how I know.
@marioiacolucci
5 жыл бұрын
Safety first always
@zakorkaz
7 жыл бұрын
The day I quit being an auto mechanic was the best day of my life. No more working flat rate. No more hot, summer shops. No more "grease monkey" label. I use my mechanical skills to work on robotics and automation now and get paid a real wage. Dealerships and the publics opinion of mechanics is what's driving the shortages. Not to mention the awful wages, benefits and amount of money wasted on tools you'll never be able to pay back. Glad I kept this as a hobby only.
@TiberiusStorm
7 жыл бұрын
I'm trying to decide a trade. I've narrowed it down to Auto Technician or Instrument technician. The Instrument Tech training looks really daunting but if I decide to do it and get through it, that'd be a much better job I think!
@salvipanda9646
7 жыл бұрын
BowHunter77 a grease monkey is a lube tech. A tech will do diags, replace parts and explain to you the whole system. Even go as far as doing overhauls of the most complicated systems such as hybrids and the like.
@salvipanda9646
7 жыл бұрын
BowHunter77 and about ur career, well not everyone likes the same thing.
@zakorkaz
7 жыл бұрын
You'll be much happier if you skip the Auto Mechanic trade. I don't know anybody that started with me back in 2005 that still works on cars. It's a terrible industry that is waaaaaay behind date.
@zakorkaz
7 жыл бұрын
I was a certified ASE tech. I was a level B tech and worked on driveability problems along with everything else that came in. Diagnosis on the rate only pays 1 hr, so if it takes you longer you're paying to fix that car out of your own pocket. Once they sell the customer on the repair you recommend you start getting paid again. You MIGHT make money but usually you end up even or below.
@Beerissmoke12
3 жыл бұрын
As a tech myself seeing this guy do an oil change made me want to yell at him, yet at the same time, I have to understand that some people just don't know how to do these things and that's why there is a market from this Service.
@ryans413
2 жыл бұрын
Some probably know how to do it but don’t have a garage or driveway or the tools too do it. Just cause someone takes there car too the shop dose not mean they have no clue how to do it
@marioiacolucci
9 ай бұрын
Great job
@ssimon64
5 жыл бұрын
Don't forget to check the old oil filter for the rubber gasket. It would suck iif the original gasket stuck to the motor and you didn't notice and ended up with a double gasket/oil leak at the filter 👍
@merkur8777
5 жыл бұрын
Left unsaid is the issue of pay. Many dealers pay .1 hours for an oil change. That's a measly 6 minutes. Carry that scenario on out to most other repairs; especially repairs under warranty.
@theseth1238
5 жыл бұрын
I've never worked at a dealership that pays .1 for and oil change. An oil change and tire rotation is .5 at the dealership im at currently. If you're making .1 you need to quit.
@fuckjewtube69
Жыл бұрын
Yeah don't worry about oil changes. Cylinder heads pay 8-20 hours. Camshafts pay 30 hours. Timing chains on 3.6 pay 20 hours. All those jobs can be done in 1 day. Oil changes are for inspections.
@annawilliams1430
5 жыл бұрын
I loved this, thank you for sharing!
@michor10
5 жыл бұрын
He forgot to go all Conan The Barbarian on the oil filter. You know, like you dealers like to.
@jlc7300
5 жыл бұрын
should have checked the air pressure in the tires too, we do
@thedavephan
5 жыл бұрын
Hand 👏 tighten 👏 the 👏 oil 👏 filter 👏
@jamesellis33
5 жыл бұрын
There is no way you are going to hand tighten the filter on that Suburban. lol If you didn't notice there is no clearance to do that. I guess you fooled a couple of people pretending to know. I work at Lincoln I should know.
@stendecstretcher4983
3 жыл бұрын
You can still service modern cars. I’m no mechanic but I service all my family cars.Tip always wear gloves and lubricate and only hand tighten the filter.
@jenkathefridge3933
6 ай бұрын
Saftey is the number one priority
@wyattandwill12
4 жыл бұрын
It's so awesome to make a living doing what you love
@nw4496
3 жыл бұрын
They used the wrong oil filter, absolutely mint
@Hamid1382
3 жыл бұрын
Car technician or car electrician??? Which is better????????
@halowatch521
4 жыл бұрын
The guy still already seems more competent then our lube tech
@PhillyDee215
4 жыл бұрын
Cool video!!!
@alfredoj9791
5 жыл бұрын
LOL tightens the oil filter with the wrench... i thought he was a veteran at his job? that filter only needs to be hand tight. what a joke of a tech
@traerose5599
5 жыл бұрын
Alfredo J right the vacuum of the system will pull it in.
@peterjedsawyer4364
7 жыл бұрын
don't change oil before a service inspection always after so you can properly identify hidden leaking.
@mr.mckinnon5680
6 жыл бұрын
Peter Schissel ... it's a Chevy pickup truck...small block Chevy... Start at the intake and work your way down. Properly identify leaks? Take your pick. do you want to fix the exhaust leak on number 7? Or would you like to fix the coolant leak between 3 and 5?
@marioiacolucci
3 жыл бұрын
Good job
@nipandebnath5993
5 жыл бұрын
which country
@richardobenshine1
6 жыл бұрын
Wow i real wish it was that easy didn't know u were auto technician because u can do an oil change smh. Funny video and yeah im cursing u out people that put oil filter back on too tight.
@recklessgamer5857
5 жыл бұрын
It’s supposed to be hand tight lol uses oil wrench
@cadenkrause8079
4 жыл бұрын
At they end they were all like “good job!! Wow!!!” He just did a simple oil change 😂🤦♂️ The service manager says this is a highly skilled profession, yet they demonstrate an oil change. Gets the wrong point across when most shops have quick lube centers that will hire anybody off the street with no certifications to change oil and rotate tires and do inspections.
@mikedewsberry1774
7 жыл бұрын
ALSO KNOWN AS PARTS REPLACERS.
@tristanfuentes5068
7 жыл бұрын
Mike Dewsberry fuck u!😂😂
@blaise-876
6 жыл бұрын
Mike Dewsberry also a person who does what they love because it's their passion and it actually makes them money
@Xixu.co.6
5 жыл бұрын
Yea because the car diagnoses itself
@joesmith482
3 жыл бұрын
Pays .20 hours and that’s the only job of the day he’ll get cause business is slow. So he gets .20 for the day
@Greg18m7
3 жыл бұрын
Bruh wears a white t shirt he obviously wasn’t informed lol
@Transient901
6 жыл бұрын
WOW...It's No wonder that people do not want to repair automobiles anymore.
@davidb8523
5 жыл бұрын
Wdym it looks fun and interesting i cant wait to go to tech school
@jefrey5578
6 жыл бұрын
This is why I never take my truck to get an oil change. Never tighten the filter with a wrench and max ft lbs for oil plug is 20 ft pounds.
@tigergreg8
6 жыл бұрын
Ya, and that is why your filter may leak because your hand position wasn't good enough to tighten it. Have fun with your blown engine.
@alfonz0010
5 жыл бұрын
@@tigergreg8 SMH
@thedavephan
5 жыл бұрын
My cars service manual calls for 25lb. So you are wrong and can’t be trusted. 😉😉😉🤪
@alfonz0010
5 жыл бұрын
@@thedavephan jackass
@lsgamiing2446
5 жыл бұрын
Lots of cars are over 20ft lbs...
@michor10
5 жыл бұрын
Please stay away from it. Just back off and give the keys to the tech. Thank you. :D
@Aussie50InspiredDavidZ
3 жыл бұрын
The dude doesn't have safety glasses on and is changing oil????? What the? Lmfaooo. What leaking fluids like coolant or oil drips down or the truck underside is full of dirt and it drops in his eyes??
@mr.mckinnon5680
6 жыл бұрын
that guy wouldn't last one day in the pits. it's all fun and games. Until the diesel rolls in. it's hilarious to hear all the dreams and aspirations of how a newbie technicians are going to make millions of dollars in the automotive industry. until they realize they're only getting paid 6 minutes at a time. and trust me, being boiled in oil and having your skin dyed black from head to toe, is definitely not worth .5.
@ramonm.1553
5 жыл бұрын
Reel Tech 😂😂 I hated the pit
@rj11wacat
6 жыл бұрын
3:03 - "This is a filter wrench right?" --- As he's putting the wrench on the filter.
@caitlynnoble8817
4 жыл бұрын
No , it not just about your son can be a automotive mechanic.your daughter could be a automotive mechanic too .girl or boy can be a automotive tech /mechanic .😡😡😡😡😡
@danielduque9941
5 жыл бұрын
i really really want to work in field of mechanic so can anyone knows want to get apprentices or helper? i'm willing to learn @Delmarva Life
@jrmob8765
5 жыл бұрын
Daniel Duque u can try too go into a community college
@donny4405
4 жыл бұрын
look up UTI (United Technical Institution)
@joshuaford9714
4 жыл бұрын
Anyone worth their salt as a tech will tell you that cars aren’t much more complicated than they were 20 years ago on the whole.
@williamcook2499
5 жыл бұрын
A JOB in this field requires a lot. And one mishap icould cost the customer and the shop a ton in so many ways. And those guys working on our car...make very little compaired to most trades when it cost so much to stay in it.... toolz are so expensive... and forever. So... hard to stay loyal to the customer. I mean the logical place for the technical person that has to be for the customers but they say fuck you about the prices it cost f9r their private privileges to drive their vehicle they bought. Most Technicians have as much money in tools to work on your piece of shit than in their home and cars combined. But the prices for a good Auto Technician don't increase. Most don't have any benifits amd retirement ... yeah.... wtfe. His toolbill out of his pocket and will never stop. His training.... will never be enough od ever stop. These cars are increasingly built more and more cheaply shile they become more nd more difcicult to diagnose and the public more ignorant of what they are paying for....to prolong the combustion engine. Enjoy that turbo.... gonna get your money's worth from that stuff like they they did in the 80's... works great... when it works. That last part.... "I think you would make a great Technician".... BLAHAHHAHAGA.... guy doesnt know how to chamge oil... didnt know what is the frame... .but didn't he say he took some sort of schooling? "Snoozing"
@basitabdul771
4 жыл бұрын
Hi sir I'm basit car mechanic I need job in your company I'm best experience pliz
@colbybryan7761
4 жыл бұрын
Damn a lot of people sure bitch about hand tightening a filter 😂😂😂.
@t-bone6864
6 жыл бұрын
What a bunch of squares.
@patcupolo9274
5 жыл бұрын
Must not be as good as rhe guy in the white shirt, I just check my oil, and get grease or oil on myself. Yes I would like a job that you don’t get dirty😇
@peterjedsawyer4364
3 жыл бұрын
GM is too easy to fix. In my experience it's just cheap Aluminum Engines easy to fix. If you want a real challenge then Fords Triton Motor would be the perfect obstacle. The Triton Motor is very powerful Engine more powerful then Vortec depending on the liter size. GM just thinks the bigger the liter size the better the outcome on a pushrod. Ford matched GM 8.1L V8 gasoline fueled with a powerful 6.8L V10 gasoline fueled. When it comes to Diesel alternatives Ford takes the Lead.
@strykerls3740
2 жыл бұрын
Wow you are so smart! Congrats asshat. LS motors always been the number 1 for swaps. They shit all over those slow ass tritons. Only good thing Ford does is the 5.0 and the power stroke.
@bodhibriar9683
3 жыл бұрын
He is one in a million, best among many, most trusted , I almost gave up on trading then I met him through a friend, Austin is the most trusted trading expert who helped the life of my family and I ,
it's not that dirty. I've seen worse. go work at Thompson industrial service for about a month. You find out a new dirty to job standards lol
@thelifestyle1296
5 жыл бұрын
Hope to work to your company
@ryanmeana6170
7 жыл бұрын
that guy dont know what his doing lol
@auxmike
4 жыл бұрын
Gloves! Use them. This kid better stick to Jiffy lube...
@brendand.2269
6 жыл бұрын
Hahahaha wheres your torque wrench clown? Lol
@joelopez40oz23
5 жыл бұрын
You are the clown if you think a torque wrench gets used in the real world when doing an oil change.
@ronijr4918
4 жыл бұрын
@@joelopez40oz23 😂😂he is a diy * probably*
@db_outlaw8278
5 жыл бұрын
He’s so hot 🤤🔥
@diegoalfredogutierrezcruz1175
8 жыл бұрын
do someone know how much money an automotive technician earn¡??
@bradenkuiper1420
8 жыл бұрын
The average salary for an automotive technician is about $37,000
@jasoncintron9073
8 жыл бұрын
i make 20$ an hour if that helps
@diegoalfredogutierrezcruz1175
8 жыл бұрын
Braden Kuiper ok thanks
@diegoalfredogutierrezcruz1175
8 жыл бұрын
j smoove thnks man¡
@baconphillip
8 жыл бұрын
diesel technician. I make $22/hr.
@fuckjewtube69
Жыл бұрын
For all the shade tree backyard mechanics in the comments. GM tells you 3/4 to 1 turn after it touches is how you tighten the filters. Yes you can do that with a filter wrench. You are backyard mechanics for a reason. Quiet.
@bjmccoy5638
5 жыл бұрын
3:17. am I doing something wrong. no that's were your weak ass hasn't change oil in a vehicle in a long time. lol kids these day man.
Пікірлер: 193