K so I worked for the CM that made the reissue. I signed an NDA and out of respect, I won't disclose the actual part number but I will say you're basically spot on. Average Vf is/was approx. 270mV when these were manually tested. As for a replacement, it's a ton of hype folks. The original has PLENTY of alternatives that will work just fine. A 1n34a is plenty close enough. I know this because I fooled the test set up we used by substituting 1n34a's in it. This is as far as I will say about this.
@scrummyvision
6 ай бұрын
based
@rnfr
2 жыл бұрын
I was a moderator on FSB at that time and yes I was in the group of folks that were in the project to degoop the Klon. It’s great to see my buddy Martin/Soulsonic get his due. Thanks for putting this record out there. It really means a lot to see this info out there.
@graybenchelec
2 жыл бұрын
Thank you! And yes Martin deserves the recognition.
@drayve8590
Жыл бұрын
Soulsonics research has helped me out immensely in building my Klones!!!
@almostliterally593
Жыл бұрын
How did þey degoop it? A ſpecific ſolvent was uſed?
@rocket69218
Жыл бұрын
@@almostliterally593 I was only a casual reader of the forum at the time but yeah, I think that was the first hurdle. Pedals had been gooped before (or after) either way it wasn't the only circuit to be gooped and finding the right chemicals to remove it without damaging anything else (too badly) was something that was talked about a lot before the Klon was purchased if I recall correctly. I wouldn't be surprised if there's whole threads on the subject of 'de-gooping' over there.
@luminousfractal420
Жыл бұрын
@@rocket69218 fair amount of chip de capping instructions out there, should be similar. Plenty of people annoyed with the black blobs covering mystery chips.
@markhammer643
2 жыл бұрын
In 2007, I received a cold call from Bill, and a request to see if I could coax the pedal into doing something that several customers had requested, *without* changing the basic design or necessitating a change o the board layout. Bill sent me two ungooped boards, one of which had every single component socketed, and a schematic. The idea was that I could sub different component values and compare the modded board to a stock unit. I made myself an enclosure with stompswitch for instant A/B-ing. Have to say I was impressed with the build quality AND the precision of the pots. We had many long chats about the design and his business practices. The schematic (which was returned, along with the boards), had a number of resistors scratched out and subbed with other nearby 1% values. Bill is no electronic engineer (neither am I, for that matter) but he has great ears, and tweaks until he hears what he's aiming for. I did not measure anything about the diodes, but I think several aspects bear noting: 1) The Klon is intended to coax a tube amp into breaking up in a pleasing manner, and was never designed/intended to be an overdrive pedal, producing an overdrive sound itself (i.e., it's *not* a "really really good Tube Screamer", that you could easily recognize by tone, independent of amp being used). 2) It's modus operandi is to provide a *blend* of clean and clipped signals in a certain proportion, that is adjusted as one rotates the Gain control. While the Treble control has both boost and cut, Bill told me he really intended it primarily for cut, to essentially "de-fizz" the signal fed to the amp. 3) While I am a hard agnostic on the differences between diodes, apart from their forward voltage differences, one needs to remember that forward voltage is largely fixed. So if one is intending to blend X amount of clipping with Y amount of clean, the diodes' forward voltage will determine both how hard that clipping is AND what the resulting clipped amplitude is going to be coming out of that path. In the same way that any issue of the Big Muff Pi can be coaxed into sounding like any other by leaving the transistors as is and playing around with the surrounding component values, I would imagine the Klon and KTR could also be coaxed into sound the same, with a change in diode. *BUT* it would necessitate hand-selecting the diodes from a batch, and changing other aspects of the design such that the clipped/clean balance at each Gain-control setting and the hardness of clipping is also preserved. The easier path to pursue is simply to use the same diodes for each unit. If the unit ONLY used clipped signal, without any attempt to blend, then one diode is pretty much as good as another, and adjusting the Gain to push them into the clipping you want is all you really need from them. But it is the strategic *blending* of clean and clipped (using a dual-ganged pot for the two paths) that is fundamental to the Klon, so diode selection, without any other changes to the design or calibration requirements, is critical. It bears noting that pretty much all diodes have a *range* of possible Vf. If I go through my bin of 1N914/4148s, some are in the range of 510mv and others up around 650. Similarly, germaniums can be anywhere from 250mv up to maybe 380mv. So, having a consistent supply of Ge diodes from the same manufacturer can assure (to some extent) that they are all very close to each other in specs, especially if from the same batch. Again, if the pedal was ONLY a distortion unit with diodes to ground, like the MXR Distortion+, batch-to-batch differences in Vf wouldn't matter. You just adjust the Gain control, and Bob's your uncle. Personally, I think far too much is made of the "knee" in diodes. Keep in mind that diodes' principle historical use is in switching circuits, with distortion/drive pedals way way down the list. Is the point at which a diode goes into full conduction important? Sure, but for speeds/frequencies well outside of what musicians, and especially guitarists, would find relevant. As a player, conducting in 200nsec vs 100nsec is meaningless. ALL specs always need to be considered in-context.
@graybenchelec
2 жыл бұрын
You know, I've heard you tell this story a couple times now, and I've always wondered; why wait until 2007 to make a change? By that time Bill was hardly keeping up with demand, waiting list was 2 months long. The klon was as big a boutique pedal success as we had seen until that point. Why change the pedal now? I can understand people pestering Bill to make the pedal do some specific thing, but surely the silence of those lining up around the block to mail order the original pedal was deafening?
@markhammer643
2 жыл бұрын
@@graybenchelec My sense is that it wasn't a "change" as much as a custom order. Despite many hours of phone talk, Bill never mentioned anyone by name. But some buyers were more like "'clients" than mere buyers. Your Joe Perrys, et al. would reputedly buy a bunch of Klons, to have one and a backup for the Europe rig, another for the west coast rig and another for the down under rig (big shot acts that tour the world often have rigs stashed all over to avoid international shipping). My experience with Bill was that he was not big on change to the pedal. I tried to get him to change from a 1/8" phone jack for power to a more standard 2.1mm jack, and even got former Small Bear proprietor Steve Daniels to find a locking 2.1mm plug/jack set from Kobbiconn that I felt would meet Bill's reliability requirements. As you know, more recent era Klons use a 2.1mm jack, so Bill eventually adapted, but it didn't come quickly. Part of the delay in production was the 20 minute "screening calls" that would eat into his build time. Another was the casting of the custom enclosure that could only be done in small batches, and impose delays as he waited for the next batch to be completed. The uniqueness of the chassis made it easy for him to avoid the counterfeiting that Zachary Vex had experienced with his use of common Hammond boxes for his early SHO pedals. But it created its own set of issues by upping production costs and imposing delays.
@graybenchelec
2 жыл бұрын
@@markhammer643 Hmm I imagine using that kobiconn jack, while I agree would be much easier for the player, would require modification of the template used for making the molds. I know Bill had enough issues getting the castings made.
@markhammer643
2 жыл бұрын
@@graybenchelec The jack itself was not really different from any other 2.1mm jack, in terms of profile, mounting, or space requirements, except that it had little slots on the side where the plug could slide into, a bit like a BNC jack/plug arrangement. Where a BNC has the little "earlets" sticking out on the jack/socket, the Kobiconn has them on the plug itself. The bonus is that ANY standard 2.1mm plug can work with the jack; the Kobiconn plug just adds that little extra prevention against being pulled out. Bill expressed that he felt the standard 2.1mm jack/plug was not as secure/reliable as a phone plug, with that little "click" of a phone plug snapping into place providing some assurance. While the male half of the Kobiconn pair provided every bit as much assurance as a phone plug (if not more because it locks), not every 9V supply used would have the male-with-ears. My sense is that the global move away from phone-plug external-power supplies, was a response to the tendency for absentminded users to produce unsettling sparks when they'd plug the wallwart in *first* and then insert the power plug to the pedal. Bill resisted this, in favour of the "phone plug click", for entirely legitimate reasons, although a compromise was available. Perhaps you are right that a change in power connector type would have necessitated an awkward or costly change. As well, and I don't say this in any snarky way, I suppose there are things about a "pro" setup that I simply don't know or appreciate. I'm not Pete Cornish. But thanks for your replies. I hope my own were not antagonistic, or painted Bill in any negative light. I'm deeply appreciative of the trust he placed in me and the opportunity he provided.
@graybenchelec
2 жыл бұрын
@@markhammer643 I don't think anything you said came off as antagonistic or critical. I had a long phone conversation with Bill, he was gracious with his time. It's clear he still has a ton of passion for his pedal. Obsessing over small details like the type of DC plug, or the specific length of the buffer switch on the KTR are exactly what I would expect.
@andrewjones4277
Жыл бұрын
I have NONE of the requisite technical electronics knowledge to understand these videos. Yet, as a lifelong gear and pedal nerd, I cannot look away. You are doing God's work, my friend. Thank you.
@graybenchelec
Жыл бұрын
Glad you enjoyed!
@rievezahl
Жыл бұрын
Facts on (germanium) diodes I learned the hard way: 1 - germanium diodes of 1 batch can vary in Vf from 0.3 all the way up to 1.9V (had authentic looking 1N34A and 1N60) lots of them were dead as I got them. 2 - not all multimeters measure at 1mA. I have one that does but also another one does at 2mA. Always check! 3 - shottky diodes usually have Vf of about 0.25V at 1mA, but there are higher Vf ones, up to above 0.3 as well. I could not tell the difference between shottky and germanium by the sound of my hm2 clone at similar Vf. Ugly sound at higher Vf silicon. 4 - the clipping circuit of my Marshall jcm900 preamp clone accepts 1N4007 diodes specifically. Every other diode sound crap. No clue why.
@fives.
Жыл бұрын
Ahhh, this is the money right here
@christopherleubner6633
4 ай бұрын
You can use either for this device, where germanium diodes are absolutely needed is an application like a rf detector where capatance must be as low as possible.
@bradfordjeff
Жыл бұрын
I worked on a similar project from 2001 thru 2004. We didn't try to duplicate the circuit. We just analyzed input vs. output and made something that did the same thing. The takeaway was that its all about the gain vs. the voltage drop from the clipping diodes. We ended up using a TL082 and 1n34a combo.
@jagmarc
Жыл бұрын
Most of what you heard came from the 1N34A
@bradfordjeff
Жыл бұрын
@@jagmarc Correct. The TLO82 does not load the guitar side of the circuit and does not color the signal, only adds amplitude.
@seanbell8216
2 жыл бұрын
I can't believe your videos only have as many views as they do. Your page is the perfect source of information for my level of knowledge. Thank you!
@graybenchelec
2 жыл бұрын
Glad you're enjoying, thanks!
@Dr-Curious
Жыл бұрын
I find OD mythology so hilarious. I changed Si for stacked Ge diodes in many pedals and nobody could EVER hear the difference. I can hear and I'm now a producer for majors. Distortion masks TONS of stuff that people CANNOT hear. The EQ manipulation and sequence is all that matters in a "stock" gain unit derived from the classic ODs.
@andrewhopkins3594
2 жыл бұрын
Good to see magic pedal component speculation cleared up with actual testing. Thanks - great channel for us pedal nerds.
@graybenchelec
2 жыл бұрын
Thank you!
@PlusDeltaM
8 ай бұрын
Fun fact: I once e-mailed Geoff Farina from Karate in the late 00's about his setup on their live album 595, it's a really beautiful tone; he told me that he used a Klon and that he actually worked for Bill at one point putting them together! He also said he got his for the "right" price.
@Mister_G
2 ай бұрын
This has been in my 'watch later' list for ages (because, you know, run time...). I have to say that It was superb and well worth the watch. I knew various bits of the story around Bill and the FSB de-gooping, and had fallen into the diode rabbit-hole when I built my own clone (1N5711 anybody?) but seeing it all laid out as a coherent presentation was fantastic. Congratulations on putting this together in such a complete way - I don't see how you could have made it any shorter.
@petersage5157
Жыл бұрын
I've read a paper about using Schottky diodes with a low value tail resistor to get something very close to the waveform produced by germanium diodes; perhaps this is one of the tweaks that Finnegan is considering. In the end, it's all about the harmonic content produced at the design voltage and current, and this can be easily analyzed with a hobbyist-grade DSO with a FFT spectrum analyzer function.
@joseislanio8910
11 ай бұрын
And you'd end up with something even more reliable
@matimoksa
11 ай бұрын
nux horseman actually use schottky
@al271987
2 жыл бұрын
The current edition of the Chellee Ponyboy has a diode switch and even at full gain you’d have to have the ears of a bat to hear the difference between the shotkys and the germanium. The fellow at Chellee basically says as much in his description of the pedal but because of the requests he got he put the option in. As Josh at JHS says, it’s not the individual parts, it’s the circuit as a whole and how those parts are used in the circuit. As someone who’s owned way too many klones (currently it’s an Emerson Golden Face, but I’ve also had the Sugar Drive, the Conspiracy Theory, the Archer, the Archer IKON, the Soul Food, the Ponyboy, v2 and v3 of the Architect, and probably a few more than that), I can tell anyone who will listen that they’re basically all the same. Some of the extra features on the ones with more than 3 knobs are nice to have, but they all sound like Klons.
@josearjona3728
2 жыл бұрын
This video is beyond amazing, man. Thanks a lot for all the work!
@graybenchelec
2 жыл бұрын
Thank you!
@cincinattiblues
Жыл бұрын
Can't believe I made it all the way through the video, very, captivating, informative and very good run through on the Klon pedal, with significance or not on those diodes and what the real run down is with them. Thank you.
@augustusbetucius2931
Жыл бұрын
Watched it all the way through. I appreciate the work you did hear. I already knew all the history and drama, but the technicals analysis was what kept me watching. Thanks, cool video.
@TheNathanMChannel
Жыл бұрын
I just want to comment on the impressive amount of editing done to remove all pauses in your speech. That’s a lotta edit points! I’ve never played a centaur myself but I still found it interesting. Thanks.
@Earthwormjimm
8 ай бұрын
Love this. Only gripe I have is I’ve never seen the klon as transparent. It has to be the most midrange heavy drive in history
@michaelinglis567
Жыл бұрын
ive been building klons for myself and friends for the past 5 years or so that i mod to have a two channel type set up. I came up with all the mods on my own except the initial gain increase that allows the second mode/boost to work. Its something i would have done anyways but ive seen it on some diy pedal kits as an optional mod so Idont want to take credit for that part lol. Anyways the way i do it is i use a second footswitch that switches four parameters simultaneously to give the klon a boost mode (which includes a boost gain and boost volume pot). But the boost isnt adding any extra circuits before or after the klon circuit its just piggybacking on existing components. I came up with this mod because most people like to use Klons as a clean boost and miss out on the great overdriven Klon tone. So by having a boost/channel 2 type option you can have both. The boost also incorporates a boost gain and boost volume pot that i put slightly above and in between the stock pots/knobs. Because of the way i get the extra gain (10K resistor in place of the 47k R16 if youre looking at the electro-smash schematic) there is enough extra gain that you can get the klon to be even more versatile with single coils. So it can do clean boost to high gain and everything in between. The klon really has much more grunt to offer that just is wasted in its stock configuration. It really makes the Klon circuit so much better in my opinion. The other important part of the mod is adding a minimum gain resistor to the op amp gain stage half of the dual gang pot. Without the minimum gain resistor in place when the boost is active you wont get a boost unless you turn up the stock gain pot a little bit. But with the minimum gain resistor you can have the stock gain at zero for a clean boost then hit the boost footswitch and get a great overdriven klon tone. The stock gain pot and the boost gain and volume are all very interactive with one another since they are reacting just as the stock circuit does. Anyways i might not be doing it justice with my explanation but the modded pedal is really great and id love to built a few extras so more people can experience it. With the boost not engaged its just a typical stock klon because my modification moto is "only add functionality/versatility but never take stock functionality away" so all my pedal builds that ive modded retain their stock functionality via switches etc.. Ive even used some of those cheap klon kits as a base for my modded klons to keep the price down for a couple friends who wanted one but are generally as broke as i am most of the time lol. I keep meaning to put together a complete pcb of the klon circuit with my mods on express pcb so i can post it and other people can build this version of the klon themselves. Anyways i just saw this an figured maybe a fellow klon enthusiast might see this and want to build a Klon with these mods also. If anyone wants to know the full scope of the mods so they can build one or mod an existing klon just let me know and id be happy to answer questions and explain more in depth how to do the mods!
@scrummyvision
6 ай бұрын
love your approach to extending existing functionality and building on top of it. I'd love to see some more details on the fully modded version; the dual channel reminds me of my Marshall combo that has two lead channels. the versatility is so big. any other mods people ask for? I'd love to make pedals for folks but I haven't lived here long enough to meet anyone
@koonsickgreen6272
3 ай бұрын
Watched the whole thing. You rock bro. Liked and subscribed!!
@NebulaStudios1
Жыл бұрын
Excellent presentation. The use of the white board and oscilloscope was the best explanation I've seen on this platform. I lived down the street from Finnegan in Brookline, MA in the 90s. I never bought one as it was expensive back in day. I saw friends perform with them, Suke Cerulo being one in the 90s. I have the J.Rocket Gold, and the Mythos versions. My JHS Double Barrel is more flexible.
@davidsheppard4850
6 ай бұрын
Great video Bro! I'm not sure how it took me 2 years to see it, but I'm glad I did. Nicely done!
@twomuttsaudio
7 ай бұрын
Fantastic overview - and made me laugh when I looked at the video duration ;-) I'm about to build a Klon clone myself, and this was perfect timing!
@scrummyvision
6 ай бұрын
I decided to put it on because I had a 1 hour car drive 😂 I knew a lot of the story at a high level but not the soulsonic bit.
@DarrenDoo
5 ай бұрын
Do you think about ever creating "lessons" on guitar pedal building? You're extremely helpful in explaining a lot of the material, super methodical and thought what a killer series you could create on the subject! Your videos are killer and I learned a lot watching this!
@evanurmy7273
Жыл бұрын
I didn’t know that I had such an interest in diodes. You successfully made what should have been boring very interesting.
@Wolf_K
2 жыл бұрын
Great video! I was around FSB during this time [2007] (still am) and all this information on the tracing, and who made it happen, is correct. In my view, if someone wants a clean boost they’d be better of with a super hard on…or even better, a self built one. My take away from this Klon business is what I’ve always known about each and every hobby or field I’ve been involved in; that is that 99% of its content and “must have” mojo is hype and nonsense disseminated by people who know very little about the fundamental elements of their chosen hobby or whatever. How many “Klon experts” could actually build a nice overdrive if you threw a handful of parts on a bench for them? Very few, I would say. This is the way of the world and always has been. Great show anyways, man! Edited to add: You should maybe start a “GBE Videos” thread on FSB and every time you do a new video post a new reply with it in your thread. It might well get you some more exposure; which would be great and inline with what FSB is all about: the free exchange of truthful information.
@graybenchelec
2 жыл бұрын
Thanks for the suggestion! I usually post the teardowns in the relevant thread, but I like your idea too :)
@XXBeOriginalXX
Жыл бұрын
what is FSB and GBE?
@augustusbetucius2931
Жыл бұрын
It was the tube screamer, the Rat, Boss DS-1 and the Boss SD-1 as the most popukar. There were plenty of others, but those were the big four in 1990. Around that time I was using the TC Electronics boost/overdrive which was and is an excellent pedal. Too bad those are also absurdly expensive now.
@OceanusHelios
Жыл бұрын
I'm no musician at all. This might make me sound dumb, but the sound from the diodes I perceived as being "wetter" and without them as "more dry." So I did notice a perceptable difference. I guess I would call it watery. Odd the words that we choose.
@erikvincent5846
2 жыл бұрын
Good video as always. I would love to see a teardown on a Harmonic Percolator or the Burns Buzzaround. I always really dug those circuits.
@graybenchelec
2 жыл бұрын
Thanks!
@erikvincent5846
2 жыл бұрын
@@graybenchelec we need to do a collab video one of these days.
@graybenchelec
2 жыл бұрын
@@erikvincent5846 shoot me a DM if you have an idea! @graybenchelec
@jalmonsalmon
2 жыл бұрын
Been using the burns buzzaround lately and now my fav fuzz. Thing is a beast
@RockAudioExperiments
Жыл бұрын
It's so wholesome to see an absolute legend here, supporting another great channel. Thanks to both of you for being constant sources of inspiration 🤘🤘
@rotaxtwin
Жыл бұрын
Interesting stuff, I don't play but I have an interest in solid state and tube electronics and putting the before/after signal on the scope was interesting. I wonder if folk have successfully used other devices to clip the audio signal and generate the harmonics, way out stuff like neon bulbs or devices with other gases in them that may give the desired non-linear effect. There is so much lore attached to a given diode part number or even an op amp in pedals - how much is just lore and how much is fact we will likely never know but it is always interesting diving in to these circuits to explore them. Your video explained things quite well IMHO and I envy your tidy, spacious bench.
@johnwebb2562
7 ай бұрын
Thanks 😊 for a wonderful 👍 video that has demistyfied the Klon. It's great to get educational info from genuine honest people like yourself. Some others wrap fluff around Scientific concepts calling them nerdy. Thanks very much. Best regards 😸.John.
@rickr7333
2 жыл бұрын
If you want to get closer to the original response of a germanium diode with a silicon diode you just add a small resistor in series to reduce the sharpness of the current curve.
@jagmarc
Жыл бұрын
@Rick R Junk the silicon! Or utilise any germanium transistor instead. Or if you want silicon then use the smallest cheapest silicon SCHOTTKY diode you can find with a trim-pot resistor
@mygreatbigfoot1679
Жыл бұрын
All these clones are all very well, but is the paint correct on your clone and have you paid more for it than anyone else on your block? The great advantage of a Klon is that the more it costs then the more professional musicians can claim back as an expense against their tax.
@oqsy
Жыл бұрын
Somewhat on topic: The MXR Sugar Drive is an excellent “klone” and seems to get overlooked because they didn’t go for the imagery associated with Klons like everyone else. Switchable buffer, inexpensive, great sound everywhere in the sweep of the gain, and one of my favorite tone knobs for coaxing exactly what I want from different guitars. If you aren’t caught up in having ponies and silver or gold on an oversized enclosure, look at Sugar Drive demo videos or try one out. I went from 4-5 “drive” pedals in rotation to just the Sugar Drive and a RAT. Excellent video, I made it to the end!
@ramilrodriguez8340
2 жыл бұрын
Great video. I built a klon clone with 1N34A and love it. However like all pedals I’ve built as clones I modified it to my liking making it more versatile. I like this circuit a lot and in some guitar/amp/other gear combinations it works perfect but in some cases I felt it cut too much low end. Mine has a bass knob(pot) among other features. I like the clean boost thing but I like much more how it sounds at higher gain settings.
@rickpapineau2704
8 ай бұрын
Very good 3 part series on the Klon circuit. I forgot I was was a tech who used an O-scope in my early years. I wonder if used O-scopes can be picked up cheap? I'm finding the "Tech" in me is coming back after watching this video and the JHS video on his Pedal building where he used an Atlas tester. I just ordered GM328A transistor/diode/capacitor/freq meter/volt meter from a Chinese company dirt cheap . I'll have to read up on what test milliamps it uses. I just retired and finding more hobbies than I years left. Basement is full of benches for guitar setup/repair/electronics testing/Cad computers/toolmakers scope/microscope with video . Garage is a full machine shop . Might have start a business. Looking forward to your next series.
@geezberry8889
Жыл бұрын
i have old boxes full of parts as i used to build pedals. i am confident i have these diodes . i remember buying all kinds of germanium diodes years ago. one day i'll go through all the boxes
@matrixmodulator
Жыл бұрын
Really nice informative video. Realizing theses diodes are harder to get or more expensive now, I ran to my stash of parts and found about 20 germanium diodes i paid probably almost nothing a while ago :)
@RickPH
2 жыл бұрын
Such an underrated channel. Looking forward for more of these! Thanks
@graybenchelec
2 жыл бұрын
Thank you!
@Jebrohnson
10 ай бұрын
This was incredible, thank you! I didn't know a single thing about these diodes going in, but I learned a lot. Thanks for the great content.
@sabbadius
2 жыл бұрын
This is awesome. SUPER clear with al the details. Thank you man. Cheers. Nico
@graybenchelec
2 жыл бұрын
Thank you!
@jonnyhafer7376
Жыл бұрын
i remember when the group bought the pedal i wasn't one of them but i was reading that thread as ive been building pedals since 2003 or so.
@lichen8855
Жыл бұрын
Great dive! Thanks for providing this. The lowest forward voltage thing I have ever discovered was using jfets as diodes and tying the "wrong" legs together. Got a forward voltage of about 0.1 on some of them. This was only on some of them. Others didn't work that way at all if I recall correctly. Probably @ 1 ma as I was using a MM
@simonkormendy849
2 жыл бұрын
My DSE Q-1804 20MHz Dual-Trace Oscilloscope has a built-in component tester, one day out of curiosity, I built a very simple diode-clipper circuit on my solderless breadboard, applied a signal to it using a Function Generator and observed the resultant waveform on my scope, I found that the clipping characteristics between silicon and germanium diodes to be quite different, silicon diodes clip the signal sharply, whereas germanium diodes clip the signal softly and the resultant waveform is more rounded than what you get with silicon diodes, I've also tried the same experiment using a couple of Schottky Diodes, Schottky diodes are silicon diodes which are designed to exhibit a forward-voltage very similar to germanium diodes, they also exhibit a very similar soft-clipping characteristic too, so, if you're building a Klon Centaur clone and you're unable to buy any good/usable small-signal germanium diodes, like the 1N34A, try using a couple of small-signal Schottky diodes instead, they should work fine.
@joerectifier
Жыл бұрын
Outstanding video…and points proven. I enjoy these topics and I think it’s great fun to search and find the tone one wants- it’s human nature. In the end, the whole Klon hype is fun to watch as a bystander - I learned a long time ago that one can take a well setup Fender Squire Telecaster to a gig with an SX300 solid state amp and get the job done with great tone….I have used that Carvin SX300 at my biggest gigs with a $600 LTD guitar and no pedals ….guitar, cable volume knob and have had some of my best fun. Still, I enjoy the hype and search and playing with these things. Again, very well done!
@KarstenJohansson
Жыл бұрын
I might be a masochist. This is the second time I watched this video. Really well done!
@shaunmacey6137
2 жыл бұрын
Great video - and really well explained. So when we talk about the qualities/properties of ANY drive/boost pedal - and the small differences in operating characteristics between Si and Ge diodes, and their manufacturing tolerances, and their operation in the context of the whole circuit (which is full of other components with manufacturing tolerances) - which you then connect to a guitar with different strings, pickup types, pickup output levels - into a huge range of amplifiers with different preamp and power amp topologies - through many different types of speaker in different enclosures - in different acoustic spaces - at a wide range of different volumes - in a band context alongside other instruments - then into your personal and highly individual listening equipment (i.e. ears) - can anybody really tell the difference? Having said that, I'm a sucker for drive/boost pedals - and I love buying and trying them! The most important thing is what sounds good to YOU and inspires you to play/practice/learn : ) Great channel and great content - thank you, and keep up the good work!
@graybenchelec
2 жыл бұрын
Yep. :)
@jalmonsalmon
2 жыл бұрын
Real world playing klones vs Klon... lol Those magic diodes are moot point
@incubism
Жыл бұрын
This was really informative, thank you! Somebody buy this man a klon.
@timchalmers1700
Жыл бұрын
Thanks for making this video. I really like the way you explain ideas that are beyond my current level of understanding. So yeah, I subscribed and I'll check to see what else you can teach me.
@Shim267
Жыл бұрын
I put a few klones together for some friends of mine and for some weird reason a lot of them liked em better than the KTR (maybe they were just trying to be nice). I did take a few liberties with some caps etc but otherwise I gave no fucks, was mostly going for reliability. I really appreciate your deep dive on this, I'm pretty well versed with a lot of this stuff but I still learned something new. Very insightful. Overall I think this is a harsh lesson in how much we get too get too mired down in the details as musicians when a lot of this stuff largely doesn't matter. Use your ears!
@echelonrank3927
Жыл бұрын
i made a klon for a musician with a switch to select a bunch of different diodes. found him using it with the NO DIODE setting !
@julesspeight8
Жыл бұрын
Excellent work, I'm building a klone from stewmac at the moment and have a prebuilt mjolnir Klone too so nice to know the real technicalities behind the diodes
@scrummyvision
6 ай бұрын
awesome video, as a fellow music engineering nerd i appreciate the extensive detail
@jimmy_jamesjams_a_lot4171
Жыл бұрын
Ahh, when one person’s personal efforts in soldering away the days building that one pedal suddenly becomes less than enough to keep up with his business - but wait!?? Why didn’t this gentleman, Mr. Bill, hire one or two electronics hobbyist friends to better keep up with the demand that was overwhelming him? There are a few business administration epiphanies wrapped up in this story. Really interesting, THANKS!! Edit: ¡¿¡DAMN!?! Also, there are a few EE Eurekas surrounding the finer datasheets points of DIODES! ¡Absolutely comprehensive, very good and insightful presentation, THANKS again!
@randalkramer1432
2 жыл бұрын
Just watched the hour long video, liked and subscribed. Also Five Watt World did a good video on the history of the Klon. I look forward to seeing more of your videos.
@omnaraiya
2 жыл бұрын
Thanks for putting this issue to rest with your thorough analysis.
@UNDERMIND_AUDIO
Жыл бұрын
This was a great ride! Thanks for doing the testing at the end. I'd like to see more of that. The general lesson I get is that we don't really know if it's the diodes that makes the Klon attractive.... So what else could it be... get into that! Thanks!
@paulperry7091
Жыл бұрын
I notice around 48:20 that the distorted waveform is not symmetric. I strongly suspect that if the signal was examined immediately after the diodes, it would be (assuming identical diodes). This makes me think that the asymmetric part of the distortion comes from the TL02 later in the circuit that has an asymmetric power supply (with respect to signal ground.) If true, this means that at least some of the charm of the Klon is from overdriving the TL072.
@jonnyhafer7376
Жыл бұрын
as you know the gain knob is a blend between the a clean and fixed gain amount. there is a resistor you can swap with a pot and then youll have control over the actual amount of gain. when i made a run of klones like 7 years ago i used separate pots for the dual gang pot. so with those 2 mods you got independent controls for clean volume gain amount and gain volume. it made for a pretty cool pedal.
@mad7stringer
Жыл бұрын
It's so refreshing to hear and see an explanation of an electric circuit from an electrical engineer! Thank you so much for making this video. It would be interesting to see the effects that different types of silicon and germanium diodes have on the circuit via the oscilloscope.
@graybenchelec
Жыл бұрын
I'm very far from an engineer, I can assure you! But I'll take that as a compliment.
@simonkormendy849
2 жыл бұрын
You can also use Leds as diode clippers as well, Leds do exhibit a higher forward voltage than small signal germanium or silicon diodes, but, they also exhibit a slow/soft turn-on as well.
@big0bad0brad
Жыл бұрын
The voltage also corresponds with the LED color, it goes from lower voltage to higher: infrared, red, orange, yellow, green, blue, UV (just like the color spectrum). Note: Silicon IS in the infrared band and actually emits such light if you expose the junction, but most infrared diodes are a little higher voltage and emit a little shorter wavelength. With exposed optics LEDs, you can get interference happening if you expose them to light - for audio circuits, especially pulsing light like most of our lighting is; just worth keeping in mind.
@weschilton
Жыл бұрын
Very interesting and well presented video! I too have a Ceriatone Centura and find that it sounds exactly like my friend's "real" late 90's Klon Centaur, for about 1/20th the price!
@kb3sjq
Жыл бұрын
Seems like the real magic is in the pre amp… Thanks for the amazing and thorough video!
@Scott__C
Жыл бұрын
I have to say I never gave a hoot about the hype. Anything with that much hype just makes me want to reject it. Great video though, really enjoyed it.
@graybenchelec
Жыл бұрын
Glad you enjoyed!
@jasonwright7513
Жыл бұрын
I currently have the J Rockket iKon, which has the germanium clipping diodes. I also had the silver version which has the silicon diodes. They both sound great in my opinion the silver has a different kind of gain which might be better for modern guitar playing. The germanium diodes produce a warmer sound which in my opinion is less transparent and more suited to blues and Americana music styles but that's just my opinion. I sold the silver version to a friend and often wish that I kept it.
@TommySprocket
Жыл бұрын
J Rockett just added a new version called the Archer Select kzitem.info/news/bejne/q6V5rZiahZuSdmU&ab_channel=Reverb Nice analysis Mr Mush and I hope your brain returns to normal all kidding aside great video it should be gratifing to you that over a year later people are still watching and responding to your views. Great job Sir!
@stevenpagano
2 жыл бұрын
Thanks, this was a super informative video. Im always intrigued about the science behind the scenes, and this didn't disappoint. In the real world, the Klon is just so juicy. Once its dialed in, its hard to resist.
@graybenchelec
2 жыл бұрын
Glad you enjoyed!
@ErinIsBlueBlue
Жыл бұрын
This was a brilliant viewing experience. Thank you ! You're a boss.
@itsbrettalan
Жыл бұрын
Mannnn, this is great! Loads of info and entertaining for us nerds out here. Lol
@lookoutleo
Жыл бұрын
You're not an expert ? You realy are . I love listening to you, your so enthusiastic :) and really knowledgeable. Thank you for posting
@purplepenguin43
Жыл бұрын
god i love hype being x-ray'd by science, excellent work
@jephable
Жыл бұрын
Great video, very well explained. I'm curious about one thing that I'm pretty sure you didn't mention but maybe was implied: Can we assume the rest of the circuit is a perfect recreation? Are the diodes the only point that have a hard to pin down variable that would effect overall EQ of the pedal? I ask because other Klone videos have mentioned that getting the distortion close to right isn't so hard, but the EQ of the pedal, the very sound of it is what's not well copied in most cases. Thanks again for all the info!
@graybenchelec
Жыл бұрын
It's a good question, but the truth is there is no "klon" sound. There is the specific-sound-of-a-specific-klon-that-person-heard-that-one-time. Electronics components have tolerances, components can differ sometimes as much as +-20% off their marked value. Combine that with the human component, which can cause us to hear things differently based on seemingly unrelated factors, like how much sleep the got the night before, or how was breakfast? There are many parts in the klon after which changing the value would provide a perceivable change in the tone of the pedal, but can we repeat it? Do we care to? Is the goal to match a specific klon sound as accurately as possible, or to create the sound that sounds best?
@WmLJohnson
2 жыл бұрын
The Klon is one of the craziest anomalies in the history of the music industry. Im glad there seems to be something measurable there. I convinced myself i could hear a difference.
@simonkormendy849
2 жыл бұрын
In a pinch, where you can't find any small signal germanium diodes, but you do happen to have some germanium transistors, you can use their B-E junctions as diodes, a transistor is basically similar to two diodes with their cathodes connected together, the cathodes forming the base, and the two anodes forming the emitter and collector respectively.
@jagmarc
Жыл бұрын
I just without realising duplicated exactly what you said 6 mths ago. Any scrap transistor radio made before the mid -70s is full of germanium
@cockysonuvaB
Жыл бұрын
Wouldn't base to ground and collector+emitter to signal fulfill the role of both diodes in parallel?
@medicallyunexplainedsymptoms
Жыл бұрын
@@cockysonuvaB Both junctions would be conducting in the same direction so you'd only clip one half of the waveform.
@YaYa-ke1zr
2 жыл бұрын
Yes, the Klon Centaur diodes are magical, just like those little chips in the Tubescreamers are magical. Tone is hidden in those diodes and chips. Yup.
@CraigHollabaugh
Жыл бұрын
Thanks for showing the pot cutout and the switch keyway. I suspect the enclosure is laser cut due to that keyway size. Thanks for the video.
@gerryjamesedwards1227
9 ай бұрын
Someone with a loop calibrator and an original, degooped Klon (ok, that's got to be a small group) could easily make a If/Vf plot for each diode. That would make finding replacements much easier. A proper curve tracer, like the Tek577, could do the testing, but those cost even more than a Fluke 78X loop calibrator, and the Fluke would do a perfectly good job.
@fen3184
2 жыл бұрын
That was extremely interesting, thank you!
@graybenchelec
2 жыл бұрын
Glad you enjoyed!
@willernst8376
Жыл бұрын
I will say I support your conclusions 100%. But I do know that an oscilloscope is actually a very poor tool to observe distortion in sine waves. Just like the human ear can not hear a difference of 5% distortion, you can not really see it on the scope either. That is why in rf engineering and other disciplines, they use spectrum analyzers or other tools to measure the real THD of the waves. A better test for the scope would have been to put a low value resistor on the diode free end and use the scope to observe the diode current under operation. That way, you isolate the diodes and only observe what current actually flows. Anyway, great video, and keep up the good work!
@10100rsn
9 ай бұрын
Yes, the germanium diodes sound the best, they are even used in the old Distortion+ pedals. But clipping distortion isn't the main point of the Klon at all, that is just a bonus. The extra voltage headroom on the output allows the EQ'd and clipped signal to be boosted beyond the 4.5vp-p (0 to +9v) and go up to about 9vp-p (0 to +18v) and this is to force the tubes of a tube amp into saturation.
@VesselForHonor
5 ай бұрын
This video is truly epic. Thank you greatly
@cliveluis
Жыл бұрын
One of the best Pedal Nerds video of all time
@GuitarQuackery
2 жыл бұрын
I can't imagine how anyone else could possibly make a more thorough video about these diodes.
@graybenchelec
2 жыл бұрын
Thank you :)
@CoenBijpost
2 жыл бұрын
Even with minimum gain there was a really slight difference on the hard hitting parts, essentially hitting harder is the same as rolling up the gain, so your point stands. At 9 there was more audible difference. It also seemed that the differences were greatest on the low frequencies, which could be correct, because diodes are frequency dependent. So the one sine might not show the full picture.
@MrKylederp
Жыл бұрын
You couldn't possibly determine that with youtubes audio compression.
@steveg219
2 жыл бұрын
Super nerdy and cool info!! Just as with debating tonewoods in acoustic guitars, or any number of such “sonic” debates, much bigger factors are the touch of the player, the precise compression/harmonics of the amp you are playing through, pickup frequency response, etc That is, what so many people get fixated on are really very small contributors to tone. If you took for example, a great electric guitar through the ideal original Klon pedal, into a really nice amp on the edge of break up and hand that guitar to two different players - the difference in the resulting tone would be greater than any diode swap, variation on any particular Klon or Klone specimen could contribute! The substantially larger factor in how you sound is the note you play imprecisely how you play them! I own an early KTR and it’s a cool pedal, but there’s nothing magical in it. It’s just a particular kind of boost with a certain freq Response and type of harmonics. What I do with it is way more important than the sound it imparts on the signal.
@meesterdinglefritz2064
2 жыл бұрын
You’re awesome man! Keep up the great work!!
@graybenchelec
2 жыл бұрын
Thank you!
@LeviBulger
Жыл бұрын
This was so well done and well taught. Thanks for doing this, Mr Gray Bench!
@graybenchelec
Жыл бұрын
Thanks!
@simonkormendy849
2 жыл бұрын
It is generally considered that asymmetrical clipping that causes a roughly-equal ratio of even and odd harmonics tends to sound the most musical to the human ear.
@Cowboybebub
6 ай бұрын
Great video, thanks!
@luiza177music
2 жыл бұрын
Very interesting video! Really cool to see the oscilloscope analysis at the end.
@graybenchelec
2 жыл бұрын
Thank you!
@danielcgomez
2 жыл бұрын
Fantastic Video! I enjoyed it a lot! ...I built 2 Centura kits that I purchased from Ceriatone, so I am quite familiar with the circuit, and now I know a lot more thanks to your video. Sub'd!
@graybenchelec
2 жыл бұрын
Thank you!
@var_guitar
2 жыл бұрын
Fascinating. The 52 minutes flew by. If by some chance you’re in New England, I have a KTR with the old diodes if you want to test them.
@jonnyhafer7376
Жыл бұрын
yep i just tested a 1n34a diode with my multimeter I got .21 and with my peak I got .35 i never even thought about this. very cool video. im subscribing to your channel and recommended you to my buddy who builds also.
@chrisfit
2 жыл бұрын
Thanks
@RogerBarraud
Жыл бұрын
Interesting. Thanks! Also: FU for starting a shortage of Russian Ge diodes!!11!! ;-)
@WeaponsRemorse
Жыл бұрын
I’ve had my arc labs? Klone for a number of years and love it
@officialdirtmcgurt
2 жыл бұрын
Good tip on the combloc cathode band inversion. D18 are pretty low Vf ge.
@lenwhatever4187
Жыл бұрын
Re:testing with diodes in and out. Having a distorting amp would mask anything that the diodes might do. Transients can easily be 10times the power of most of the sound and it is difficult to hear them being clipped but they do affect the overall sound making it brighter. Can't hear that with your test setup though. Also, It will be acting as clean-ish compression/limiting in the "clean" zone. As a further note, the wave shape at the output shows a relatively large amount of high end roll off. It would be interesting to see a variety frequencies input or to take the output from the end of the diodes plugged into the board. I notice someone below has suggested series resisters on a silicon diode to simulate the germanium curve. That would have some effect, but I think not the same as germanium diodes. Maybe if the signal is kept within the non-linear portion of the curve it would be close. Also to use a silicon diode, the non-linear potion would have to be larger than the germanium to make up for the higher Vf and the higher preamplification needed to compensate. I suspect that silicon diodes where the voltage of what is now the ground were to be individually held at a voltage that artificially lowered Vf enough, the curve would effectively become a closer match to germanium or even softer. Of course the gain structure would have to be revisited as well. Listening to Paul (of PRS) talk about components for amplifiers and design of pickups is well worth while. Over all, a good talk. It has been almost 50 years since I built my first "fuzz box" using a couple of opamps and some diodes (silicon at the time). I realize this is an older video and you have done more on the topic since.
@willernst8376
Жыл бұрын
Hey there. I like your comment. But one thing. When you referred to the wave shape "having a high end rolloff," that is really not the case. If the wave is part of a frequency graph, that would indeed be the high end. But this is just a single frequency, it has no high end. The distortion of a single tone can not be used to infer whether a filtering action is present. It is the amplitude of many waves that determine response. Looking at a sine and saying that the high end is rolled off is not possible. Now, I don't know if the actual response has a low pass or whatever, but I know we need other info to see that. I agree with the other stuff, but I left a comment above about how scopes are pretty poor tools for this in general. I'm sure you will agree
@lenwhatever4187
Жыл бұрын
@@willernst8376 Actually, when a wave is distorted and no longer a sine wave, it contains many higher frequency harmonics. A square or triangular wave have infinite harmonics (or tries to). Diodes used to clip will try to square the wave giving many odd harmonics. If you take a square wave (like on an old school synth) and run it through a low pass filter, the wave form becomes more triangular shape (saw tooth?) which is what we are seeing in this trace. My interest was if this is built in filtering downstream of the clipping diodes or if the filtering effect was due to the diode pair themselves. Perhaps due to the slew rate of the diodes in question or the loading of the diodes or even as part of the hysteresis in the diodes transfer function. To really compare any two diodes would require a more dynamic test. I can see why the original diodes were selected by sound but I suspect that a proper dynamic test could automate the same process in a way that merely measuring the static transfer function could not. My ear for sure is not that good.
@willernst8376
Жыл бұрын
@Len whatever yep you are right about harmonic content of non sine waves. But my point was that you can not say the highs were rolled off. If anything, the highs are increased. Though you probably were bot saying that nayway. I thought that the shape of a rolloff on the right side of the sine wave was being conflated with a rolloff in the frequency domain. Obviously, I was wrong in your assumption there.
@grillsandaxlegrease3578
Жыл бұрын
Pedal or not - I'm here just to get caught up on my diode knowledge.. Let's see if I learn something!
@gerryjamesedwards1227
9 ай бұрын
You can find NOS germanium transistors around that might be worth a try connected as diodes. The large non-linear region and If/Vf curve should be similar.
@joaquins90
Жыл бұрын
If I had to guess, for using a more common germanium diode, with a higher Vf than the originals, two things could make it behave closer. Increasing the resistor previous to the diode (and decreasing the cap if going extreme, but likely not needed), and second increasing the level of the previous stage and then attenuate it back down to the correct level. Tweaking those two parameters should enable to archive the response of the original. Of course, knowing how much or if you actually got it it's quite hard without an original one to compare, but a bit of math could make it pretty close, with the limited amount of info (0.35V@5mA). The other characteristic that could change from diode to diode is the junction capacitance, starting with a similar Ge diode could help, but given that audio is pretty much DC for most diodes, I wouldn't personally sweat it, adding a few pF in parallel could, at least, discard the difference is noticeable. I mainly lost the original talks about the clone as I was much less evolved with pedals by 2007, I do know a bit more electronics now than when I was messing with pedals. I know this is an old video, but the kc talks never ends...
@ToddBeck76
Жыл бұрын
Making a 5mA current source to test Vf with a standard multimeter is quite easy. You really want something that can trace Vf across a varying current ramp, though. Then compare alternative candidates against Vf measurement curves from known true Klon Centaur diodes.
@Nathansillav
Жыл бұрын
There is a visual difference when you did the on and off diode testing, this effected tone
Пікірлер: 470