Just had the same issue and replaced the water pump. Now it works again.
@kaydenheyhey
3 жыл бұрын
Hey Andy! Were you ever able to fix the this problem? I'm having the very same issue and trying to figure out if I should get a new generator. This is driving me nuts so your help is much appreciated!
@173Bean
Жыл бұрын
Did you happen to find a fix for this? Thanks
@zee1272
2 жыл бұрын
ESAM04110S Hi - I replaced my pump on the Delonghi Magnifica because it was not delivering water anywhere - the steamer now works but the coffee part is not delivering any liquid - any suggestions ? - There are no leaks . I’m an amateur but I’m willing to try ! If so do you know where I can get the parts and directions to repair myself? Thank you
@bryanduffy6362
9 ай бұрын
Solenoid is the problem its 40 bucks on amazon
@crosswindjones
9 ай бұрын
Thanks for the idea! I typically buy parts at ereplacement parts but if you have an amazon link I'll try it. I have found if open the water rez, slam it back shut, run hot water.. the error corrects and will work for a while without issue.
@davidolinsky
3 жыл бұрын
I had the same problem this morning. I made the mistake of pulling the water resevior to quickly fill while the machine was running. Did you need repairs? If so, how much did it cost?
@EyeTentacleTwin
9 ай бұрын
I made that same mistake of pulling the water reservoir before it started brewing because I thought I could be quick enough to get more water in before it brewed. Ultimately I had to get a new pump. The machine is about 6 years old. After I made that mistake it would no longer make coffee. Running the pump in test mode ran the water through the brew path okay, but any time it had coffee grounds in it the pump would get quiet after a second or two and I'd get the low flow error. I cleaned everything thoroughly but there was no scale. The screen on the infuser looked a little clogged but some bleach helped that. I replaced the orange brew group O-rings and then thought it just needed to be re-lubricated but that also didn't fix it. Eventually I just bought a new pump (Ulka EAP5, about US$22). I ended up leaving the electrical part in place so I didn't have to unglue the overtemp sensor and just changed out the "wet" part that is secured to the motor body by 2 screws. I took the old one apart and everything looked fine, but it must have some small amount of damage that was preventing it from building the pressure needed to brew coffee.
@173Bean
Жыл бұрын
Exact same issue here. Any tips for resolution? Attempted purging any air bubbles by running the steam wand for over a minute.
@addanera2822
3 жыл бұрын
I wonder what the cause of the problem is. I have the same problem with esam 3200. Do you have any answers?
@addanera2822
3 жыл бұрын
@@crosswindjones i disassembled the water pump but i don;t see any problems there. Maybe you are right! if you have any results please let me know. I will do the same. Thanks for your response!
@addanera2822
3 жыл бұрын
@@crosswindjones i searched all videos about fixing esam about water problems. I did not see anywhere that the problem should be the generator.. i dont know which part should i take so i fix it. I agree with your wife!! :)
@addanera2822
3 жыл бұрын
@@crosswindjones Andy i have good news for you!! the answer is here """" rounded.com/delonghi-generator-6mm-diameter-new-version-5513227881.html """""" (I did not know that this spare part is called "generator", i thought it is called boiler or thermoblock.) So if you change it, it will definitely work. I promise. But you have to be very carefull with the screws..you have to put your other hand below every screw so that you unscrew it. I did it about 7 times..., because i could not find what part of generator needs deep cleaning. Now i will tell you a secret.. By normal automatic decalc procedure, this part, the generator, DOES NOT REMOVE CALCIUM (white stones that clog the plastic tubes of the genarator. Every time you have to clean it by yourself..This site helped me a lot www.kaffee-welt.net/index.php/Thread/5707-Delonghi-magnifica-kommt-kein-Wasser/?pageNo=2&s=26b85afec28db9364d89794923f4e07aaf379b1e . Is in german language but they give many valuable technical information about problems. Now I wish you good luck with your machine! i will wait for you to tell me you fixed it!
@SaifurRahman-dh5ut
3 жыл бұрын
PROBLEM: Water not coming through DeLonghi Magnifica ESAM 3300 brewing unit. ROOT CAUSE: Pulled out water reservoir while machine was running. The water pump pulled in AIR into the tubing. As a result, the air bubble was trapped in the system and water was not being pumped into the brewing unit. Coffee beans were being ground but not pressed/brewed with water. Powder was being emptied into the collector inside the unit. CORRECTIVE ACTION: To pump the air bubble out, the hot water dispensing feature was used to pump water through the frother. You can hear the bubble being pushed through the tubing unit. Let this run for a minute or so, to ensure the water stream is smooth. Once complete, brew coffee as normal. Enjoy! No disassembly required! PREVENTATIVE ACTION: DO NOT PULL OUT THE WATER RESERVOIR WHILE THE UNIT IS RUNNING!
@crosswindjones
9 ай бұрын
@@SaifurRahman-dh5ut I do believe this is the right answer. At least for my situation. I have found that when the above condition occurs, I pull out the water rez and push it back in hard,almost a light slam... then run hot water nozzle for a few seconds the issue is resolved for another while. It works but is not a real solution... I will try the solinoid replacement -can't hurt.
@markp6982
Жыл бұрын
Mine does this. What is the solution? No beans get ground. Heater does not appear to work. Pump works when lever put on steam. No water comes through.
@Yourcheerz
10 ай бұрын
Did you find the solution?
@markp6982
10 ай бұрын
@@Yourcheerz Boiler was dead. I changed that and it works fine now. Great coffee maker and parts are not expensive if you shop around.
@crosswindjones
9 ай бұрын
This is not my problem and I have replaced the flow meter multiple times without any improvement BUT it is good information related to this issue: kzitem.info/news/bejne/0Xdjrohra4iWZoI
Пікірлер: 20