Dude. Super helpful extra informative and well presented vileo
@paulpenn766
6 ай бұрын
Very thero good information well put thanks for all that helpful information.
@buckgreatdane372
Жыл бұрын
Very well said.and done no doubt.
@Shakez76
3 жыл бұрын
Very very good video! Great detail and camera angles. Thanks man. Bout to pull a clutch off a buddies bike to see what is going on. Just as you say. Tough shifting...very sloppy to get it into neutral...the light even shows but the bike isn't in neutral, and I can feel it dragging. Thanks again for the video and I hope you make more.
@norsemencustomcycles7289
3 жыл бұрын
Thanks man! I have full intentions of making more. Just kind of renovating the shop at the moment. After that I will be making more videos. Im glad you enjoyed it!!
@GaryAllan-ux1qb
Жыл бұрын
BEST VIDEO TO DATE!! MUCH NEEDED INFO, THANX FOR HELPIN ME OUT ,KEEP EM GOING MAN YOUR VIDEOS ARE NOT ONLY HELPFULL BUT SPOT ON MAN AND I THINK YOU GOT WISDOM BEOND YOUR YEARS AND YOUR VIDEOS SHOW CERTAIN TYPE OF CLASS WORTHY OF THE 1% DIAMOND .MUCH RESPECT AND GREATFUL TO HAVE WATCHED ..
@guzzifabrication3448
3 ай бұрын
Solid info brother
@rayceballos8316
Жыл бұрын
Excellent video Brother, Thanks...
@raybolis8606
3 жыл бұрын
Sweet Job Mr, Thanks from the Motor City Detroit,
@pipesmcgee9270
2 жыл бұрын
Thanks for a great video. Same for a big twin Evo I imagine.
@josedelagarza5087
3 ай бұрын
Thx great information
@stevenworth9430
3 жыл бұрын
Great Detail! Thanks!
@tomhopkins6758
2 жыл бұрын
Nice work Thank you for the time
@tmarx88
3 жыл бұрын
Good video, just one question and i've looked all over having a hard time finding the procedure for hydraulic clutches. Once I reassemble the clutch pack, i have to keep taking it for a ride, take off the cover, adjust a 1/4 turn each time or half, just can't seem to dial it back in to where it was before. Got any input on this?
@doublenickelbob
Жыл бұрын
Does the sharp edge of steels face in or out?
@tjeco10ify
3 жыл бұрын
Thanks 😃
@lindseyyip1608
3 жыл бұрын
Behind the first friction disc are two rings: one is flat and the other angled. Not paying attention, I removed them to clean and now don't remember which way the angle ring goes in. Can anyone help me with this?
@norsemencustomcycles7289
3 жыл бұрын
The flat thin ring is your damper spring seat. The angled on is your damper spring and it will be orientated in the clutch hip so you see it a concave. And they will be added first and in that order.
@scottculton
Жыл бұрын
Good video ! Covered everything real good thanks much appreciate it! Hey for your closing since your named Norseman how about the word norsemen close out thier conversations with or saying goodbye or hello “ALEAU”
@diablo-km2ot
3 жыл бұрын
after adjusting my clutch cable, soon i ride my bike few miles my clutch lever starts to get all wobbly lots of slack and cant change gear what can it be.
@norsemencustomcycles7289
3 жыл бұрын
Throw out bearing or the ball bearings in the ball and ramp assembly could have fallen out.
@diablo-km2ot
3 жыл бұрын
@@norsemencustomcycles7289 Thank you so much, I don't think i have a throw out bearing, my clutch it like yours so it might be the ball bearing will give it a try this weekend :)
@claresmith7227
Жыл бұрын
Almighty Teacher, related to ball bearing question, I'm not sure if I hear your video well, but I think you conducted two ball bearing tests using the clutch lever to verify if the ball bearings were still in place during assembly. First test before adjustment.) Pump clutch lever once, that was before the adjustment cable internally. Second test after adjustment.) Pump clutch lever three times, after the adjustment cable internally. If these two ball bearing tests (before and after) adjustments were done and a ball bearing was missing, What's a failed test look like when a ball bearing is missing? Also, Will this ball bearing test work for Sportster models too? Thank you. Clarence, Michigan
@benodie02760
Жыл бұрын
Absolutely great attention to detail! Little clattering going on so time to tackle this job. Appreciate the knowledge!
@norsemencustomcycles7289
Жыл бұрын
@@claresmith7227 a failed test will will have tension initially and once you pump the lever the tension will dissappear.
@BMFRich65
2 жыл бұрын
How do you know when the clutch bearing goes bad?
@norsemencustomcycles7289
Жыл бұрын
I have a video coming out about that this spring
@diablo-km2ot
Жыл бұрын
put a new clutch and fixed the Throw out bearing or the ball bearings in the ball now its running great.
Пікірлер: 29