I made it all the way to putting the hub back on and broke the aluminum inner spokes. Had to order a new kit. You should mention in your video that you don't want to apply too much torque tightening that thing, lol.
@ggsmith23
2 ай бұрын
Same here. Take care
@robsonbass6058
3 жыл бұрын
So, I bought it off eBay and just now took my stone guard off. The bearing is basically gone. I was afraid the compressor itself may have caused the breakable part to break. Looks like it'll work. I'll just finish up this yogurt and get back out there. BTW, I used the 1/4' drive socket, but with an adaptor for the larger ratchet. Worked great. I also just grabbed the solid ring on the stone guard with vice grips to spin it off. Still on the car. No wonder the belt was always squealing. I think I actually had it TOO tight. Edit: Done. That was absurdly easy. The car runs very quiet and the AC works great! This video saved that car. I was going to dump it. Maybe I CAN get it to 300k.
@billwilliams2057
2 жыл бұрын
WHERE DID YOU GET THE PART LINK PLEASE
@robsonbass6058
2 жыл бұрын
@@billwilliams2057 I looked for it based on my vehicle. I'm out of town right now and my new phone doesn't contain all my email addresses. When I get home tomorrow I'll look it up on my desktop and check back. BTW it is still working great!
@robsonbass6058
3 жыл бұрын
Heh. I have a Scion xB (1st gen) with 225k miles on it. I bought the car new and love it. I replaced my noisy alternator a couple of months ago (due to noise) only to discover it didn't help the noise. Yesterday the noise got really bad, and I noticed the AC wasn't blowing cold air any more. There was a terrible rattling noise, almost as though my engine bearings were about to seize up or something. Well, it was the AC compressor that was making all the racket. Thinkint it was the AC clutch I did some KZitem searching only to find out it was clutchless. This brought me to this video. I know it's the compressor pulley mechanism because the outer plat didn't spin while the engine was running I can see from the wheel well because the plastic plate is gone (after hitting a deer 75k miles ago). But I can turn the outer plate fairly easily by hand. I assume the compressor is still functional but it may not be. And when I looked at it from above with the motor running you can easily see the inner plate rattling around between the pulley and outer plate. This video showed me how to either take out the inner plate so that it is quiet (but no AC) or how to replace the whole setup, assuming the compressor is not shot. Looks like I just need to replace the inner plate, if it's even available, if I think the AC might still work... I guess we'll see. I'm SO glad I had the new shop building built. This would suck to try to repair on my lawn. :) BTW, seeing as how I had a dickens of a time getting the belt to stop squeeling when I replaced the alternator, I suspect the compressor is done. After all, something had to cause the inner plate to break.
@boostv8chevy457
2 жыл бұрын
hi. Can you tell me if you have splved the squeeling? what was the cause? and how about the Ac compressor? Mine squeeling come and go. and my ac dont cool when about 1000rpm
@poshrobert
3 жыл бұрын
Man I was looking for this for days Jeep Patriot 2007 has the same clutch compressor and you save me a lot of work thanks, I’ll suscribe
@billwilliams2057
2 жыл бұрын
DID YOU GET A LINK TO GET THE PARTS PLEASE HELP!!
@realista1
Жыл бұрын
Perfekcyjnie wytłumaczone brawo, zamawiam klucz i biorę się za wymianę.
@Boss-hg6ul
Жыл бұрын
The front cover broke off today? Is it still safe to drive you said something about if it fails it breaks off?
@Detroitthermo
3 жыл бұрын
Pesh, are you able to find a replacement pulley for your compressor? Just swapping the pulley is a pretty cheap and easy thing to do. Erik
@peshpraq5137
3 жыл бұрын
Hi No unfortunately I could not find it anywhere that is why I gave you the specifics for the part wondering if you had it. Any way I bought the complete compressor now and replaced it . But I want to buy those tools of you. Many thanks for your reply
@peshpraq5137
3 жыл бұрын
I checked the tool on your eBay it is reasonably priced but shipment cost is too high I was wondering why that is high.
@Detroitthermo
3 жыл бұрын
What is your location?
@peshpraq5137
3 жыл бұрын
@@Detroitthermo England UK
@edgarmacario4635
2 жыл бұрын
what is the name of the extractor and the other tool
@stewartcross9939
4 ай бұрын
Brilliant video only one I could fine on line Brilliant example 👍👍👍👍
@mannypack6983
2 ай бұрын
Question! Do you have any idea my car had broken two times the midle part? I already put it second time amd broke it again!!!😢
@coolissimo69
3 жыл бұрын
Great job great help I need to do this with my AC.
@billwilliams2057
2 жыл бұрын
WHERE DID YOU GET THE PARTS?
@ghumman68
2 ай бұрын
Good informative video to help for such work ❤
@MILTONQUE
3 жыл бұрын
Hi, do you have any link to buy the pulley kit? I mean the pulley with all the rubber separators including the bearing… thanks.
@terminalclub8527
2 жыл бұрын
Dziękuję za film, juz teraz wszystko wiem.
@Detroitthermo
2 жыл бұрын
Zapraszamy
@dannyg2143
6 ай бұрын
Hello, disciple, what bearing number does the compressor use? Could you tell me?
@busted4n6
6 ай бұрын
Any idea on torque spec for tightening these back up?
@gregrobinson5725
3 жыл бұрын
Do you have a link for me to order the part and tool? I have a 2010 Corolla with a broke plastic pulley on the compressor
@MATHEWLB
3 ай бұрын
I have Toyota Corolla 2010 model ,it's ac compressor some time make grinding sound ,only compressor mode on time what is the remedy? Please help me
@christodav
2 жыл бұрын
Thank-you so much. I have just placed the order for one of your tools to be sent to me in Australia. Climatepro - is that you?
@WakaiPapa
Жыл бұрын
can u tell me the code of bearing please
@arronpowell1292
Жыл бұрын
I made mistake of taking that smaller Uber ring out seal blew out can I get that seal and put new seal in or do I got buy new compressor
@isaacfriesen6793
Жыл бұрын
Hi, I’m Isaac hey, do you sell those pulley and hub? And also the tool for a dodge avenger
@ScottXDavidson
4 ай бұрын
R & Y Compressors on eBay sells the pulley, and Detroit Thermo (also on eBay) sells the tool shown here.
@ScottXDavidson
4 ай бұрын
Does that wrench tool you made fit a 2014 Dodge Avenger 2.4? Denso 6SEU16C compressor.
@ScottXDavidson
4 ай бұрын
Chrysler 200 and some Jeeps have same engine and I would imagine same compressor also.
@EmmanuelGontchoM
5 ай бұрын
Did you buy it online ?
@osmaidepalaciomartinez3695
Жыл бұрын
Question I gt a2004 scion XB nd I need a pully how can I gt one from u ?
@robsonbass6058
3 жыл бұрын
Just ordered a new one. We'll see if this fixes everything...
@kisekkapaul9962
2 жыл бұрын
Great work
@Detroitthermo
3 жыл бұрын
You can buy on eBay www.ebay.com/itm/333988991724
@noelsanchez1822
Жыл бұрын
Thank you good video
@TonyMartin-l1i
22 күн бұрын
wear do i get theas items from you
@erichayes2182
2 жыл бұрын
How do I order one of the pulley assemblies
@cesarcan7386
Жыл бұрын
where can i buy this tool?
@zahoorcarac
2 жыл бұрын
Good work
@peshpraq5137
3 жыл бұрын
Hi I have a denso compressor which is making knocking noise but the ac is working. The part number is GE447280-6570 and it is 5SE12C. Here in England the mechanics go for replacing the entire compressor , and if you tell them to change just the pulley they will think you got some sort of mental problem. The car is a toyota avensis deisel 2.0 D4D of the year 2012. I need your opinion and wonder if you have the part and if it can be bought from you and sent to me. I will very much appreciate your help sir
Mine made that exact sound for a couple of months until the inner ring snapped completely. Now the outer plate is not spinning with the pulley, but it is spinnable by hand. i.e. it will keep blowing cold until it sheers completely.
@mdsoulsounds
3 жыл бұрын
In France the same, they want to replace the entire compressor, 1100-1400€ parts and labor. Haven’t found a garage willing to change only the bearings, more profit changing the entire compressor !!
@GregScavezze
Жыл бұрын
It appears that this doesn't release the coolant and that you could do this without removing the compressor?
@trythis2821
Жыл бұрын
Correct, as long as you have enough space or can make room to do the job. Looks like my Yaris I can remove some inner plastic wheel arch to get to the ac compressor.
@ScottXDavidson
4 ай бұрын
Correct
@bitacoraextrema6543
3 жыл бұрын
Name of the tool can put a lick to buy please
@Detroitthermo
2 жыл бұрын
Yes, it's me, thanks Chris
@nihonkokusai
2 жыл бұрын
which socket and could you use the belt to counter it?
@Detroitthermo
2 жыл бұрын
7mm deep socket
@aishelbernadina6330
3 ай бұрын
Whats the parts number of this cluch???
@ianknapp3917
Жыл бұрын
Is their any chance you can link the tool so I can buy it I can't find i anywhere?
@Detroitthermo
Жыл бұрын
Search eBay for Detroit Thermo, you will see all my items including this tool
@tonyespino2442
2 жыл бұрын
Sir, can you add you the link to your store.
@rogershuart6676
3 жыл бұрын
No entendí hablo español pero la guía visual me sirvio mucho, muchas gracias
@corinazamorez6596
2 жыл бұрын
How much for the pulley
@doloressalazar2821
2 жыл бұрын
Where can I buy one for Toyota Yaris 2008?
@Detroitthermo
2 жыл бұрын
www.ebay.com/itm/333988991724
@gustavoreyes8195
3 жыл бұрын
Donde consigo esa herramienta?
@kervinjoseochoa3255
2 жыл бұрын
Como se llama la herramienta 🔧 que usas para remover el closch
@Detroitthermo
2 жыл бұрын
www.ebay.com/itm/333988991724
@HMH_Hidraulica
Жыл бұрын
Hola tendrá código de rodamientos? Valering numbers please ?
@wayniefrazer9723
3 жыл бұрын
what if the bolt is damage
@coolissimo69
3 жыл бұрын
Where can I find the tool?
@Detroitthermo
3 жыл бұрын
It's on eBay www.ebay.com/itm/333988991724
@jamesoneill3475
3 жыл бұрын
Any1 got a link to where I can buy 1 of these spanners..
@Detroitthermo
3 жыл бұрын
On eBay, the seller is climatepro, the brand is Detroit Thermo
@Reneacor
2 жыл бұрын
Too late for me, I broke. Thanks, I did not do a good search.
@Detroitthermo
3 жыл бұрын
www.ebay.com/itm/333988991724
@rentacarnarail97
Жыл бұрын
Are you give me your tols
@chriss4365
Жыл бұрын
Why cant they make it like other cars with one bolt not this dumb design that you need a special tool for. A plastic pulley what a joke. So to replace the pulley you need to remove the engine from the car great Japanese designers here.
Пікірлер: 78