Outstanding video, THANK YOU! For those who may purchase this table, when you get it home, the first thing you do is open the box and throw the instruction booklet in the garbage. Watch the video. This gentleman tells you everything that you need to know.
@RaptorMachineToolCo
Жыл бұрын
Thanks Frank, glad the video helped you ! please Like and subscribe ! Joe
@magicsounds1
3 ай бұрын
Your right about throwing the instruction booklet in the garbage.
@JohnSpitzer-b4d
3 ай бұрын
Great video and very helpful. As he said the instructions are pretty worthless. I have the 8-1/4" Dewalt jobsite saw and it mounts a little differently than the 10". The 8-1/4" has rubber handles at the bottom. These do not need to be removed. There is a hole in the bottom with a threaded connector in the tub. I found it easiest just to flip the saw upside down and rest it on the box. That way you can connect the two brackets from the stand directly to the stand. The bolts supplied with the stand are used to connect the two brackets through the holes in the handles. You won't need the nuts.
@andys2497
2 ай бұрын
I’ve just spent 15 minutes ranting and raving swearing and cursing smashing my fists on the table and generally having a mega Wendy on. Thank you very much indeed matey I’ve launched the nuts into the nut graveyard ,,,,,,,,,,,,
@Dognme
Жыл бұрын
Not sure how you got all that information out of the book, but I’m glad that you did, many thanks
@RaptorMachineToolCo
Жыл бұрын
glad it helped! please give a like, thumbs up, and subscribe! joe
@thehonestman26
2 ай бұрын
Thank you. I was stuck on step 1 and felt like an idiot. I was able to get the alan wrench in the hole by rotating the key, and I found the nut under the bumpers to be 5mm. But why is this table so short? I'm only 5'7", and I kept looking for a way to adjust the height. I can only imagine if you're taller.
@magicsounds1
3 ай бұрын
Thanks just got a Hercules table saw from Harbor Freight had one issue the bolt by the switch had to put in the other end but still works
@writerbj
8 ай бұрын
Thank you!! I was going nuts trying to attach the saw to the brackets! Why is the manual soooo bad?
@drksam
4 ай бұрын
Thank you! Much more informative than the pictorial/worded manual provided by dewalt. My problem now is mounting a King brand table saw to the stand. Dewalt recommends a piece of plywood... not sure of this. Might just drill the holes directly into the saw bracket and mount it that way....🤔
@RaptorMachineToolCo
4 ай бұрын
I fabbed up a sheet of 3/4 pc of cabinet ply to accommodate a small miter saw on my dewalt miter saw stand.. for jobs where i dont need the large sliding miter saw.. i picked up a small light one. Purchased an extra set of mounts... works great ! thanks for watching .. please like and subscribe ! happy woodworking ! Joe
@BazookaIke
Жыл бұрын
The angled holes on the saw are to run long screws through them to screw the saw down, if you don't have it mounted to a saw stand like the one in this video. I have always screwed my saw down like that but just recently bought this stand. Thanks for the video help!
@RaptorMachineToolCo
Жыл бұрын
Good to know! I have always just put it on the bench. Thanks for watching! Joe
@afpitbull60
8 ай бұрын
Your video came in handy as I just purchased the exact setup. Thanks!
@etmesi
2 ай бұрын
I used extra washer too on the little rubber feet. I’m trying to mount this to the Dewalt 8 1/4 inch table saw hope it works.
@etmesi
2 ай бұрын
As it turns out yes this stand fits the 81/4 inch dewalt saw. The saws feet stay on with the 81/4 inch saw there’s a hole through the feet for this stand. A lot easier to handle, only thing the wheels are about 24 inches wide the saw won’t store on the shelf where I had it, I have to make a new space for it. The con for the 81/4 inch saw Dewalt says do not use it with a dado blade darn. I’m sure if I had to I’ll figure something out.
@alanshaw4655
2 жыл бұрын
plastic round insert for the allen wrench : it would have fit , but you installed the plastic insert upside down inside the kick stand tube. table saw mounting bracket , left side: it's supposed to sit in the chrome bracket. reason : keeps the saw from moving while you are rolling it around.
@RaptorMachineToolCo
2 жыл бұрын
thanks for the note !!! hope you enjoyed the video otherwise.. please like and subscribe ! Joe
@alanshaw4655
2 жыл бұрын
@@RaptorMachineToolCo you are most welcome !. ordered this very stand today from amazon for my dwe7485 table saw, that i also purchased today. not gonna lug my floor shop table saw around, too old for that now..lol.
@docjody8624
Жыл бұрын
Hey there. It says Allen (hex) wrench stows in the "handle." Does it instead store in the kickstand? If so, exactly "where"? Driving me nuts. Handle has FOUR holes, none of which accommodate the little "L-wrench."
@boyzuo
2 жыл бұрын
Thank you. Saved me a lot of time.
@RaptorMachineToolCo
2 жыл бұрын
Glad it helped you out ! thanks for watching ! Joe
@mattfrazier3115
Жыл бұрын
Thank you very much!!!!
@docjody8624
Жыл бұрын
It says the small Allen (hex) wrench included in the box can be stored in the retractable handle. The handle has 4 holes in it. The wrench falls out of all four easily. Where "exactly" (precisely) is the wrench storage location?
@pjdegroot1
Жыл бұрын
Thanks! Had to take the computer out to the garage.
@RaptorMachineToolCo
Жыл бұрын
Glad you got it together ! thanks for watching.. please like and subscribe.. Joe
@Falcon47-47
16 күн бұрын
I have a table saw with mounting holes about 24" wide. Would it work on this stand?
@RaptorMachineToolCo
16 күн бұрын
i believe it would.. if you look toward the end of the video.. you can see the mounts are slotted.. they should fit a wide range of widths... thanks for watching ! please like and subscribe Joe
@shelmom533
Жыл бұрын
How did you make this taller? I'm only 5'3", but I will have to work on my knees!!!
@RaptorMachineToolCo
Жыл бұрын
LOL yes im 6' it is kinda short...
@johnstrange6799
2 жыл бұрын
There you go :)
@RaptorMachineToolCo
2 жыл бұрын
thanks John !!!
@johnstrange6799
Жыл бұрын
@@RaptorMachineToolCo How is everything going, Joe?? Well I hope.
@RaptorMachineToolCo
Жыл бұрын
@@johnstrange6799 good buddy, how are you? liked your music videos.. but commenting was turned off.... hope you are still machining a bit !
@johnstrange6799
Жыл бұрын
@@RaptorMachineToolCo Hey-Hey! Glad to see you thawed out from winter. Glad to hear you are well. I can't complain (But still will). Thanks for checking out the music vids. Might have new stuff coming at some point, not sure. Yeah I still machine stuff when I make or repair things. Business as usual there. You still at it too??
@RaptorMachineToolCo
Жыл бұрын
@@johnstrange6799 yes! should have some new videos soon.. working on a lot of stuff here !
@davedaniels8211
2 жыл бұрын
Purchased stand and saw on a deal . Instructions very misleading . You tube clips helped .
@RaptorMachineToolCo
2 жыл бұрын
Dave, glad the video helped ! thanks for watching.. joe
@jacobmaier8993
10 ай бұрын
Why is it so short? Made in China?
@RaptorMachineToolCo
10 ай бұрын
isnt everything ? im 6' and its not so bad.. taller would be better tho.. thanks for watching ! please like and subscribe
@jacobmaier8993
10 ай бұрын
@RaptorMachineToolCo ya, once I got it together it really isn't bad
Пікірлер: 42