Hi Daniel, first of all don't be dissapointed by the dislikes, if it fun for you, just keep doing them. On the other side i will try to give you some advice, not an expert but also trying to do some CNC reviews. You do have to be carefull not to compare apples with oranges and not to mix up the specs. Both units, 485 and 481 are Brushless units, but as the price is different also their torque is different, those numbers will tell you which is stronger. Is good that you are comparing with the same baterry type, i hope they are freshly charged and same "age". A which one is better has little sense 481 is stronger, spec based, but also the price is like double. But you still showed the difference nicely, like from my side Note:The screwdriver mode has the clutch, the 21 steps, that gets activated at the 485, offcourse since the unit has less torque, the 21 setting will be "weaker", as it has to protect also the mechanics, motor not blowing up and so on. Also you should clamp down the part you are working one when drilling with such a massive cutter head, to give a good example for anyone whatching your channel. For sure you are not responsible is someone gets hurt, but a good example will help reduce the risk of injuries among the hobby makers :) Keep it up!
@danielazad4421
3 жыл бұрын
Thank you for your encouragement and great advice Fabian. I really appreciate it.
@nbmufc94
3 жыл бұрын
Good effort Daniel. I enjoyed it. They are very different drills. The 485 is great for DIY work around the house or small jobs and the 481 is much more powerful hence why you are provided with a handle. It also has a metal chuck whereas the 485 has a plastic one. Keep the videos coming, you will get better with each one
@sizif717
2 жыл бұрын
Daniel, you have some very nice tools. Just ask someone to show you how to use them. What are the different modes for, the 2 speeds, etc. You don't do power screwing in clutch mode, the clutch mode and all the numbered settings are for sensitive screwing.
@remedy7295
3 жыл бұрын
Let's compare both drills DHP481: max torque 115Nm, capacity in wood 76mm, price approx 170-200 euro DHP485: max torque 50Nm, capacity in wood 38mm, price approx 100-120 euro
@Richard1977
7 ай бұрын
That holesaw he used was more like 50mm. Under those conditions you should praise the DHP485 as it did get thru the timber.
@leonardemraj2184
3 жыл бұрын
Of course the dhp481 is way stronger than dhp485 . The dhp481 is the most expensive top of the line makita drill and dhp485 is just the middle class don't be fooled by the model number check the specs instead because makita is weird with model naming makita dhp458 has a maximum of 50nm of power in other hand the dhp481 has a maximum of 115nm it has more the double of the power and so there is no compparision between these two end of story ! Thank's !
@kylemoore79
Жыл бұрын
Put it in drill mode not screw mode
@ichundich5599
3 жыл бұрын
please learn how to use them right, it hurts to see how less you now about the drills.. the 481 perfomes better putting in your screw because it is in drilling mode (in which the force clutch is disabled , the scale from 1 to 21) and on the 485 your in skrew mode (in which the Force clutch is enabled) so for right comparison put 485 and 481 in drill mode and try to put the skrew in again....
@ichundich5599
3 жыл бұрын
your right that 481 is stronger, but with this little skrews there is no need for more power then the 485 can bring to the table.....the 485 is able to put much longer and thicker skrews in wood than the one you use for demonstration......
@izzyizzy2783
3 жыл бұрын
Plz stick to parkside tools bro
@danielazad4421
3 жыл бұрын
I used Parkside before but they are not as good as Makita Izzy. I think that was garden paint spraying machine. The tool was shaking and too noisy.
@akosfisher
2 жыл бұрын
Daniel keep going!
@SMFJose
Жыл бұрын
Great 🎉
@weedjuice2917
2 жыл бұрын
a bit painful to watch but entertaining
@matic2601
Жыл бұрын
Hi, 485 and 481 are both brushless. The 481 has more power but is also more expensive so what is the deal here?
@pajunen3
3 жыл бұрын
Slower gear for that size cup drill.
@jimmytwizzle7836
3 жыл бұрын
No wonder this guy has more thumbs down than thumbs up. Crying out loud.
@danielazad4421
3 жыл бұрын
Feel free to comment guys 😀👍
@busbuilduk1397
Жыл бұрын
Good effort pal but find someone to show you how to use those tools correctly
@der.kdf.brother
10 ай бұрын
I was thinking the same. Must be Romanian.
@armlovebow999
3 жыл бұрын
Impact driver
@danielazad4421
3 жыл бұрын
Combi Drill
@felix807
Жыл бұрын
Compare 481 with 486!!!! Not a A klasse Mercedes with a Man truck!
@teobalas2724
3 жыл бұрын
you dont know how to use them clearly
@danielazad4421
3 жыл бұрын
I thought it was very informative Teo.
@LOL-zt8zp
2 жыл бұрын
使い方全くわかってないやん
@danielazad4421
2 жыл бұрын
LOL
@amblernectar
3 жыл бұрын
Absolute shambles. Take the tools away from this guy
@leo-nj7cc
Жыл бұрын
Mate get a different job , leave tools to the trades men , what a joke
@michaelbignell2385
20 күн бұрын
Not a very scientific comparison, lot of jabber in commentary
Пікірлер: 37