really good concise video. Should help a lot of people.
@Corn-ped
3 жыл бұрын
Thank you! I m trying to make em simple but informative!
@RedSiBaron
3 жыл бұрын
@@Corn-ped you're doing a good job keep it up.
@alanhayward6719
6 ай бұрын
Excellent video!
@Corn-ped
6 ай бұрын
Thank you very much!
@briangtester2536
11 ай бұрын
Har, in DK, back in the eighties when i rode these (Not the maxi, that's a girls bike ;-), i remember us grinding down the heads, they had a full centimeter of rim on it to lower compression! On top of that the piston shown here was know as the "race piston" because the regular one had the compression rings lowered something like ½ - 1 cm below this one. Here in Denmark all mopeds (still) are restricted to 1 (one!) horsepower and 30 KM/H :-D (thanks MoooooM! ;-) )
@Corn-ped
11 ай бұрын
Oof. That would be a slow ride!
@DuviousGangsta
Жыл бұрын
Old video, hope you’re still around to see this. When using a gauge to check compression, how specific is the sizing? I wanna get one but I don’t wanna make several trips finding the right size lol thanks!
@Corn-ped
Жыл бұрын
It's real specific. See what size spark plug you use and get one for that size. My mopeds use a 14mm spark plug.
@DuviousGangsta
Жыл бұрын
@@Corn-ped rad! Thanks for the quick reply.
@Corn-ped
Жыл бұрын
Yeah man! Remember to hold the throttle open when you check the compression
@codyfranklin2305
11 ай бұрын
hey bro i see all the exhaust u have hanging around.....i got one just like this one its a 1.5hp model maxi luxe 1978 model. 5/78....any way u would sell a stock exhaust?? mines rusted out right after the header pipe bend.......
@Corn-ped
11 ай бұрын
Why not buy a nice new one from treatland. Tv
@andrew9nation
3 жыл бұрын
Do you think the ring was defective to break like that or is this normal? Good video, thanks
@Corn-ped
3 жыл бұрын
I think it was just defective. It didnt have any damage, it had a clean snap. . .
@romanbobrek-hw5qc
Жыл бұрын
What would of been your next step if the ring wasn’t the issue?
@jacobmylsted
4 ай бұрын
My spark disappears after a few kicks in the kickstarter and it just won’t start what do I do
@Corn-ped
4 ай бұрын
It disapears? I would try a new spark plug first. Check all your grounds. If a new spark plug doesnt work, and your grounds are good. Then I would test the coil.
@andrewbrown22fret
3 жыл бұрын
Good video, what did you use for a compression tester and whats the margin for error? Harbor freight c tester is usually like 40psi off of actual
@Corn-ped
3 жыл бұрын
I used a handy hand held one. I don't know what the tolerance is but is fairly accurate. I would use a screw in one with the throttle all the way open if I wanted to know the exact comp. This was more to illustrate that it had no compression.
@Zeljko-Lovric
11 ай бұрын
What carburetor is it on this one?
@Corn-ped
11 ай бұрын
That was a clamp on Dellorto PHBG from Treatland.tv
@Zeljko-Lovric
11 ай бұрын
@@Corn-pedwhat size?
@Corn-ped
11 ай бұрын
I think this was a 19mm
@Zeljko-Lovric
11 ай бұрын
@@Corn-pedThanx a lot. Love your Maxi videos 🎉🎉
@Corn-ped
11 ай бұрын
Thank you!!! @@Zeljko-Lovric
@Monkeyboys69
6 ай бұрын
I have an puch x50-4 that dont want to start, its been siting for a very long time. I have tried to clean the fuel filter and put new fule in the tank but still it does not want to start.
Пікірлер: 27