Hi, yes wanna see the front dial, because i've made few attempt like that, with very parametric point soldering machine, and I always face a tiny discoloration on the front, never achieve a perfert solder
@AnilVerma-wb9fs
2 жыл бұрын
Thanks for vedio, I need the equipment used. How much would it cost and name of device from where can get it . Thanks in advance pl tell me. 👍
@ivamatsushige9653
4 жыл бұрын
Thanks for your video. Could you tell me which wire diameter you are using, the wire material (copper or brass) and the characteristics of the power supply?
@jockoharpo2622
3 жыл бұрын
It turned out perfect but you never showed us the front of the dial.
@stevesanchez8369
6 жыл бұрын
Great work Stu... I have a dial that needs new feet can you repair it for me?
@Mars-zgblbl
Жыл бұрын
Many seem concerned about the risk of damaging the dial finish with heat. Has anyone here tried placing the front of the dial on a wet cloth or sponge while soldering the feet?
@bobansomoi7101
2 жыл бұрын
Can you tell me how to make this machine?
@knobexploitmusicelectronic9218
7 жыл бұрын
please use a pop shield for you mic.
@alavipalliyan4669
2 жыл бұрын
What is the name of soldering paste?
@joaquinpendleton948
4 жыл бұрын
Please what is the voltage of your power supply. thanks, Joaquin I am a watchmaker also ------- As Time Goes By ----is my business name
@electromech8931
6 жыл бұрын
what is name of machine? and machine brand sir?
@67herby89
6 жыл бұрын
Great video. I found a demonstration video here on KZitem of another soldering machine which I Purchased and have used several times with great results. Here’s the link to his video which I highly recommend you watch. His contact info is: Oscar 1(323)896-9368 kzitem.info/news/bejne/y6aw1oGAg4upi3Y
@konstantinsuvorov2980
7 жыл бұрын
Good evening, tell me please, how can I make the same device? Do you have a schematic?
@67herby89
6 жыл бұрын
Great video. I found a demonstration video here on KZitem of another soldering machine which I Purchased and have used several times with great results. Here’s the link to his video which I highly recommend you watch. His contact info is: Oscar 1(323)896-9368 kzitem.info/news/bejne/y6aw1oGAg4upi3Y
@henkvandeleur6872
7 жыл бұрын
Is er geen verkleuring van de wijzerplaat waarneembaar?
@sstakoff
7 жыл бұрын
No discoloration - the heat is very localized. Geen verkleuring - de hitte is zeer gelokaliseerd
@67herby89
6 жыл бұрын
I found a demonstration video here on KZitem of another soldering machine which I Purchased and have used several times with great results. Here’s the link to his video which I highly recommend you watch. His contact info is: Oscar 1(323)896-9368 kzitem.info/news/bejne/y6aw1oGAg4upi3Y
@sanusihadi8416
4 жыл бұрын
👍
@screamingcockatoo
6 жыл бұрын
Did it mess up the finish on the front?
@67herby89
6 жыл бұрын
I found a demonstration video here on KZitem of another soldering machine which I Purchased and have used several times with great results. Here’s the link to his video which I highly recommend you watch. His contact info is: Oscar 1(323)896-9368 kzitem.info/news/bejne/y6aw1oGAg4upi3Y
Пікірлер: 22