Jut finished replacing my wash plate and it was stuck on good. Used your process but ended up putting a socket on the center bolt and hitting it with the air hammer, that did the trick for me. Hopefully this will help someone else get theirs off. Thanks for the video.
@tedrstedrs6690
22 күн бұрын
I've seen the shaft come out before when I worked for sears. Was just trying to change a hub and couldn't get the wash plate off. I wouldn't hit it with the metal hammer lol
@darrylmccormick4607
Жыл бұрын
I just did this EXACT procedure...and had the same results!!! Those airbags are very strong I've found. Anywhoo...just waiting on the new part (spline's were entirely gone). I'm going to drive that back in and see what happens....wish me luck!
@foreverendeavors6210
Жыл бұрын
Still using this one, so far so good.
@darrylmccormick4607
Жыл бұрын
@@foreverendeavors6210Well re-seated mine and no issues but I did find that although the plastic part I just replaced now has good splines the metal shaft seems to be almost stripped as well. Geez...decision time lol....
@louiszagar1270
19 күн бұрын
Hello. OK, FOllow the bouncing ball here, this is not that difficult. FIrt, remember the splines that connect the wash plate to the transmission are tapered! Prying up on ANY side of the plate only makes things worse since it pinches the splines together and all manner of yankiing on the edges simply tightens the two splines even more! Here is the best way that worked perectly for me: First, once you remove the center bolt, pour either heated white vinegar or a good spray of BLASTER around the bolt hole making certain it gets into the splie area. Let that soak in for at least an hour. Next, gently tap all around the center collar of the plate including tapping both sides of each impeller vane. NOT TOO HARD, just enough to break any corrosion between the two splie parts...make and female. Probably should NOT hit down onto where the bolt was...that will only further jam the splines together. Not doo. Now, take a GOOD pair of channel locks, tightly grip anywhere around the top edge of the bolt collar (the raised circle that surrounds the bolt), and yank up. Voila, it should come right out but make certain you pull it STRAIGHT UP and not torqued to one side of the other. All the other methods only worked againsT you. And when you are ready to replace the impeller or wash plate, make certain you take a good brass brush and clean out the splines as much as you can to remove any loose corrosion. Take a tooth brush soaked in blaster or WD40 to clean out the inside of the plate spines. Then, coat both splines with a good Anti Seize lubricant (Permatex is a good choice in the gray tube). Replace the wash plate or agitator and exercise up and down gently to evenly better distribute the lubricant. You are done. Relplace the bolt with the BLUE Lock Tite lubricant. Now if you need to remove it at a future date, repeating the above provess will allow the plate to be removed easily if even you need to do that. And no, the lube will not stain your clothes. It is fully encapsulated by the tight fit of the two splices. Enjoy.. Dr. Z (Lou)
@Wasupup
2 ай бұрын
Little never seize on the spline before installing. Easy out
@rivera75nesto
15 сағат бұрын
I literally torn my in pieces and chisel it out lol , tried citrus acid soak but didn’t work
@foreverendeavors6210
15 сағат бұрын
@@rivera75nesto some of these are truly big stuck!
@pastoroscargomez4346
Жыл бұрын
Good video, thanks.
@danielrufledt5246
Жыл бұрын
Did it work? For long.
@foreverendeavors6210
Жыл бұрын
Still using it.
@tedrstedrs6690
22 күн бұрын
Nitrile gloves brother 7 to 9mil
@bmccabe2147
Жыл бұрын
That’s not a snap on bike or motor cycle tool it’s a snap on brake drum adjuster spoon
@brandonbewvlogs
Жыл бұрын
wow
@KathleenThompson-xn3gv
11 ай бұрын
this just breaks the washer
@davidortega600
Жыл бұрын
Just had the same issue. Is the shaft still in place?
@foreverendeavors6210
Жыл бұрын
Still using it, no issues.
@rickpausan
2 ай бұрын
your system is a failure
@foreverendeavors6210
2 ай бұрын
@rickpausan I don't have a system, I have a method.. 😆, and the whole video was how when it "failed," I made it work anyway 🤪. "It's not how many times you get knocked down in life. It is how many times you keep getting back up and keep fighting," Rocky 💪..
Пікірлер: 21