I solved the issue with my G572XP Pro. Turned out to be the coil. I replaced it with a new OEM coil. The saw fired right up and now runs better than it did initially. I’m sure that it revs higher than it did initially and doesn’t bog out.
@thefirewooddoctor
26 күн бұрын
Last time I ran it, was a bit finicky on carb tuning. It would scream or slightly 4-stroke.
@botabob
Жыл бұрын
I'm no saw expert, but here is what I would check. The air and fuel filter. Check the fuel. I hear a lot of people experience problems with TruFuel. And the last thing I would check in the cylinder and piston for scouring. If it was run with straight gas the cylinder could be burnt up. Like I said to begin with, I am not a saw doctor, but always check the simple things first. Good luck.
@thefirewooddoctor
Жыл бұрын
It never had straight gas. Always the good Husqvarna oil in it. Is possible the fuel line has faield from sitting so long.
@thefirewooddoctor
Жыл бұрын
The problems have been found. You'll see what happened to it in an upcoming video.
@yungkelly8102
8 ай бұрын
@@thefirewooddoctorcould you let me know how you fixed this I’m having the same issue
@thefirewooddoctor
8 ай бұрын
@yungkelly8102 turned out it was a wonky air intake manifold fitup. Had the fuel tank vent replaced and had the carb reinstalled. Runs like a champ!
@Coonhound-outdoors
Жыл бұрын
Did you ever find out what was wrong with it? Mine doing the same thing
@thefirewooddoctor
Жыл бұрын
Is in an upcoming video. Actually had to replace the fuel tank vent, plus the air leak was an ill fitting carb manifold.
@vincentnail2881
Жыл бұрын
Replace the impulse line, and put the original cap back on. Check the vent tube, to make sure it is connected. Replace the carburator if none of that works.
@thefirewooddoctor
Жыл бұрын
The carb was replaced 2yrs ago, ran perfectly fine before the fuel tank vent failed. So tried the vented cap, still acting up. Having the shop take a look at it after pulling the muffler to see if the top-end is scored. If is scored, is a parts saw as far as I'm concerned.
@thefirewooddoctor
Жыл бұрын
The problems have been discovered. Stay tuned to hear what they are!
@vincentnail2881
Жыл бұрын
I'm curious.
@thefirewooddoctor
Жыл бұрын
3wks or so when that video is released.
@rocketruss3405
2 ай бұрын
@@thefirewooddoctor so what was the issue? I don’t seem to be able to find the video covering it ?
@proforest1
Жыл бұрын
Vypadá to na špatný přivzdušňovací ventil nádrže, dělalo mi to to samé. Nahradil jsem originálním a pila jede.
@thefirewooddoctor
Жыл бұрын
Sorry, I cannot respond as I cannot read your language or understand it.
@proforest1
Жыл бұрын
@@thefirewooddoctor
@proforest1
Жыл бұрын
i have the same saw and it had the same problem, it couldn't get the full fuel tank out, the engine kept cutting out. I replaced the tank air valve with the original one and the saw runs like a dragon. it really needs the original valves, the ones from China rarely work properly.
@thefirewooddoctor
Жыл бұрын
@proforest3631 the cause of all the problems has been found. An air leak has been fixed, cylinder and piston are fine.
Пікірлер: 25