Liked this system level walk through where we could actually see how you are doing a reset/adjust. Thanks a lot, Vee. Very helpful.
@anabaperslife9579
Жыл бұрын
Thank you for liking the video! Glad this could be of help. I know I had struggled initially with this 🙏
@rohithpillada5675
2 жыл бұрын
Good video please continue doing the videos
@anabaperslife9579
2 жыл бұрын
Thank you 😊
@Prashant29thakur
2 жыл бұрын
Informative .. cleared most of the doubts
@anabaperslife9579
2 жыл бұрын
I’m glad:)
@ananthakrishnanm4707
2 жыл бұрын
really helpful videos about SPAU and SPDD phase
@anabaperslife9579
2 жыл бұрын
Thank you 🙏
@sitaramkorla8275
2 жыл бұрын
Very nice video.thank u so much
@fachrezardotcom
2 жыл бұрын
My God, this helps me alot...thanks Vrushali.
@anabaperslife9579
2 жыл бұрын
Thank you 🙏
@gurjeetkaur7096
2 жыл бұрын
Thanks for this video Vrushali👍
@anabaperslife9579
2 жыл бұрын
Thank you 🙏 Glad it helps:)
@akshaydamodaran7457
6 ай бұрын
Thankyou so much
@rakshithas9329
Жыл бұрын
Hi Vrushali, this video helped me a lot. Thank you ❤️ I was able to perform SPAU successfully. only issue I was not able to adjust the TABD object type as I don’t know how to adjust it.. if I click on adjust its displaying the table. Not sure what to do in this case
@kat-8994
Жыл бұрын
At 35:18, why did you reset when there were custom adjustments on the right side?
@wanted2476
2 жыл бұрын
Hello Vrushali, What is the significance of change processing status n mark for testing?
@anabaperslife9579
Жыл бұрын
Change processing status makes the system know that the object has been checked and looked after. When the SUM activity is resumed after SPAU/SPDD, SUM rechecks if there are still any open objects, and checks the processing system status. Mark for testing is only an indicator for users, in case anyone wants to test the new adoptions .
@harshavardhanb7789
2 жыл бұрын
At time stamp 8:17, we have difference in sap version and system version, line 18, 23 and 24 of system version are commented in SAP version, any specific reason why we have not adjusted these changes?
@anabaperslife9579
2 жыл бұрын
Hey, yes there is. The changes on those lines were brought in by the Support Pack Upgrade, so are basically updates to the standard code of the existing standard code. So we don’t need to change them. The changes that we do need to adapt are the ones captured by the system TRs.
@RachakondaSrinivas
Жыл бұрын
last few minutes were the most confusing for any ABAPer . why did reset for few objects and why did u adjust the last one ? why can't u explain which objects should be adjusted and which ones to be reset ?
@asiyanizam6178
2 жыл бұрын
Sometimes for red one in With Assistant, when I go for Adjust option, splitscreen editor doesn't open, only single version of the object comes. When I go back then the object status changes to something else and cannot do anything. Can anyone tell what should be done in this case?
@anabaperslife9579
2 жыл бұрын
You need to open that program separately in another transaction for editing, and then check the version management
@mishaemir
Жыл бұрын
I have same issue, the split screen editor is not showing, can help how to fix it? Is there any config needed? I expect have split screen editor also during adjusy
Пікірлер: 24