Incredibly helpful 7 years later on my NX10 on a Flight Test G-44 Widgeon using a Spektrum AR630 receiver. Works perfectly! Thanks!
@mountaindewdude76
4 жыл бұрын
i've been flying rc's for about 9 years and never needed differential thrust. I've got a build going on right now that has twin motors....needing differential thrust. Although I have a Gen 1 DX8, I was able to follow your video, step by step, and I now have differential thrust working. Awesome! Thanks for your video!!!
@stevenungester927
Жыл бұрын
I tried this on the DX8 WORKED GREAT!!!! however I learned you can't do throttle cut! this was THE CLEAREST EXPLAINATION I HAVE EVER HEARD. THANK YOU SO MUCH SIR! Keep doing great videos!!
@georgesager1573
Жыл бұрын
Steve I hope you can help me. I just setup differential thrush and have the same problem with throttle cut with Aux 1. It works just fine with the motor plugged into the throttle on my receiver. How did you get it to work on both motors? George
@stevenungester927
Жыл бұрын
@@georgesager1573 are you on Facebook?
@georgesager1573
Жыл бұрын
@@stevenungester927 yes
@stevenungester927
Жыл бұрын
Hit me up on Facebook... I'll connect you with the right person
@MrBIG4D
2 жыл бұрын
OMG!! You JUST saved my sanity!! I have been trying to set this up on a boat (I know, don't bash me) and I have been PULLING MY HAIR OUT!! I knew it was possible because I have seen it done! THANK YOU for posting this video!!!
@Eugensdiet
2 жыл бұрын
Very nicely done. I've watched a bunch of how to's on Tx setups and they are always hard to follow but your's was very clear . In addition this is exactly what I wanted to learn.
@philthayer4087
Жыл бұрын
Cool, I think you need to not only increase the motor on motor x but also reduce the opposite motor. Much smoother and you can still steer at WOT
@rob737700
5 жыл бұрын
I just used this video to set up my hobbyking Lancaster (recently built a spare that I have had for years in the basement). I usually struggle with programming, thank you for making it easy and fun! hope to see more of these tutorials.
@chrisstolle5664
5 жыл бұрын
lancasters are sweet planes!
@johnvinson1939
3 жыл бұрын
From the AMA Feb 2021 edition of the Model Aviation magazine, I've started the build of the model on the cover. It's called the Yin-Yang and your video is nothing short of awesome, and because the model doesn't have any rudder control, (it's solid), your video will help me with my dual motor, (one a pusher, the other a puller or tractor as you call it), differential thrust setup. You have helped me more that I can say and I thank you for taking the time to create one of the greatest and easy to follow videos, that I have ever viewed. Again, thanks for eliminating one giant headache for me and at the ripe old age of 82, (just had my birthday in January), the fewer problems I have to solve, the more time I have to enjoy my Golden Years and the RC hobby that I entered into about 6 years ago. THANKS! THANKS! THANKS!
@Scraboview
8 жыл бұрын
It's an 11 year old foam semi scale kit which was designed for 400 size brushed motors and nicad batteries. My idea was to tart it up a little and over the years I have almost rebuilt the entire airframe, adding retracts, using brushless motors/ ESCs and lipos. as a result it has taken me too much time so far and I have decided that it needs to earn it's keep! Originally the rudders were to be fixed and I had plans to activate them, but the servos and linkages were going to add some unwanted weight at the wrong end of the airframe, so your info should allow me to gain some yaw control. I have connected the tail wheel to the rudder channel and now have the option of adding differential thrust for accurate ground handling/ taxiing. Thanks again.
@8poundquark
3 жыл бұрын
Thanks for your help! No need for a water rudder anymore! I used this tutoring today to set up my PBY and aside from switched channels, I'm set.
@Hootysdad
2 жыл бұрын
This is exactly what I was looking for. I am about to begin a Grumman Goose build and I definitely would like to have differential thrust with this plane for control while it's on the water. Thanks for this perfect explanation and setup.
@georgesager1573
Жыл бұрын
Ron were you able to setup throttle hold for both motors? I haven’t been able to get throttle hold to work on the motor plug into Aux 1.
@d.c.r.ccountryman7453
4 жыл бұрын
Excellent job explaining how! i used this and had NO problems setting it up on the first try. i give it a 10!
@wingsab
3 жыл бұрын
You must be a teacher. Fantastic instructions.
@chrisstolle5664
3 жыл бұрын
Spot on. I am a teacher! And I see you are a musician? I am as well.
@aarons7836
4 жыл бұрын
what a beautiful demonstration
@gustavbork4664
6 жыл бұрын
Omg... this is the video we all have been wating for🕺🏿💪🏽
@nateolmsted22
4 жыл бұрын
Every time I set up a new dual motor toy, I rewatch this video haha probably done it a dozen times now but I can never remember it all. Thanks man! Great video
@chrisstolle5664
4 жыл бұрын
Kind words!
@RARenfield
2 жыл бұрын
Clearest explanation ever. Thank you.
@mightynuthead
7 жыл бұрын
Great thanks, Mr. Stolle. I used this on the DX6E and took me 5 minutes to get a working twin plane. Awesome !
@chrisstolle5664
7 жыл бұрын
5 minutes? Not fair. Took me hours to figure out.
@mightynuthead
7 жыл бұрын
World is full of unfairness, Mr Stolle. But it's nice to know that somewhere on earth there is someone who is very grateful to you. :-)
@chrisstolle5664
7 жыл бұрын
Best reply ever!
@bindasbanna
6 жыл бұрын
Please confirm the full model name
@bindasbanna
6 жыл бұрын
Chris Stolle Sir, please confirm this differential thrust settings can be done in Futaba T6K 6 Channel 2.4GHz T-FHSS
@braddixon3338
7 жыл бұрын
And another great thanks for this video. really simple to follow and understand, just the way I like it :-)
@Scraboview
8 жыл бұрын
Many thanks, Chris. Just the guidance I needed for my Lancaster with no rudders.
@chrisstolle5664
8 жыл бұрын
Lancasters are sweet! Scratch build or kit?
@danreynolds8028
4 жыл бұрын
Great job Chris! Damn I would have never figured this out. I have a new Avios Albatross and need to set this up on my DX9 so I can water taxi without having a physical rudder in the water. EXCELLENT EXPLANATION. Subscribed!!!
@OhMySack
4 жыл бұрын
Just picked up an Albatross, too! Bitchin' plane and my first twin and of course...needing differential as well! What rx did you use. I have a new 637T or a 9350 I can tear out of my big Carbon Cub. Trying to get my head around what I won't have if I use the 6 channel 637T.
@Hootysdad
2 жыл бұрын
Roger this!!! I am about to build a Grumman Goose and also need directional control on the water. This will work out perfect for m.
@VladooDIY
4 жыл бұрын
So many thanks from france! You save me time and stress :)
@av8tore71
4 жыл бұрын
I have the new DX8G2 and follow ya because there are NO VIDEOS for the DX8G2...GRRRRR so I'm writing to send you a HUGE THANK YOU because I tried following Josh from Flite Test and he has you putting the leads in port 5&6 and using a curve plus he was using a totally different TX. So again thank you so kindly Sir!!
@chrisstolle5664
4 жыл бұрын
Glad it helped!
@brucei8767
4 жыл бұрын
Chris, thanks for this video. I've accomplished Differential Thrust previously but it was UGLY. I just took my G44 Widgeon (twin engine seaplane) and bound to this...wham bam perfect.
@chrisstolle5664
4 жыл бұрын
Glad you found it helpful!
@dcsmith5839
5 жыл бұрын
I know it's an older post,but Thank-you.I have a DX8G2 that this will work on. Got the basics,but the mixes and channel assign are a bit of a black art to me.Much easier to see than read about it.
@Hoomi2
Ай бұрын
Worked great for the newer DX6e as well. Thanks!
@sailor0500
5 жыл бұрын
Thanks for taking the time to upload that Chris.It is by far the best explanation I have seen and will use the info shortly. Mike.
@chrisstolle5664
5 жыл бұрын
Glad it could help!
@unclerojelio6320
6 жыл бұрын
Thanks! One thing to note, if you are using this configuration with a DX6e, don't use the Flap system. The flaps use Aux1 and you can't select it in the Input Config screen.
@thejourneyproduction2753
4 жыл бұрын
Roger Banks how do I make differential thrust work on the dx6e then? I’ve spent around 2ish hours searching for something but I simply just give up, do you have any idea?
@scottfirman
6 жыл бұрын
So regular throttle is just both engines. Thats pretty awesome! Anyone that builds their own plane can use that. If you buy a twin engine plane, chances are, it already has a set up in the esc for thrust vectoring. If something happened and you needed to replace the electronics, this would be a great way to set up all new electronics in an older plane that has been sitting that you wanted to upgrade.
@Sabotage_Labs
4 жыл бұрын
Pretty funny cause.... I Just built THE Guinea Pig too and setting up differential for the first time. Good video man. Helpful and fast!
@goku519862
7 жыл бұрын
This was awesome. It also worked for the DX6e.
@haydeninch
4 жыл бұрын
Thank you so much for posting this tutorial I would have struggled by myself. Nice Guinea pig by the way. I am making a FT Master series p-38 and want rudder authority.
@GDSFlyboy
6 жыл бұрын
Thanks for your brain. Mine is not that good. Need this technique for my next seaplane project. Well done on the vid.
@chrisstolle5664
5 жыл бұрын
Thanks man
@erad05
5 жыл бұрын
Thanks a lot for this descriptive instruction for the DTh Setup! The best I could find so far.
@chrisstolle5664
5 жыл бұрын
Glad it helped
@thomasstephan366
4 жыл бұрын
Did this on my AL37 Airliner with my DX8G2. I used aux 2 since aux 1 is for flaps. Thanks for the video. Just have the throttle trim centered.
@ConservativeUSA67
2 жыл бұрын
Thanks for making this super easy. I was going nuts before your video ;)
@mmmasterscross7915
6 жыл бұрын
Thanks so much. I needed that for my Avois Bushmule.
@alanbier
4 жыл бұрын
Wow. Great video/instructions. I'm building a FliteTest P-38 and using a spektrum DX8 gen2. This Video saved the day!! Much obliged. ALB
@roddraym
3 жыл бұрын
Chris, Thanks to your video, my understanding on this topic is much clearer! Thanks for sharing and Happy Holidays!
@davidrush9204
2 жыл бұрын
Thanks so much - this is an amazing explanation of how to do this!!!!
@chrisstolle5664
2 жыл бұрын
Glad it helped.
@gracefulbutterfly
6 жыл бұрын
Thanks for posting this and making it easy to understand. This will be helpful for setting up my BushMule.
@thecompositescompany6589
4 жыл бұрын
As many have said, great tutorial on setting up differential thrust. I have an HU-16 Albatross, where both differential and reverse thrust would be interesting. I've learned a great deal about the DX6 transmitter, but I'm not sure how to reverse both motors with the flip of a switch and retain differential thrust as well.
@shvancy
3 жыл бұрын
Great video! Worked perfectly for my 4 prop Lancaster. Love the simple step by step, easy to follow and understand:)))
@DaveLprintz
5 жыл бұрын
U R Awesome! Thank you very much! U saved me hours of frustration with this most excellent video. If U are not a teacher or professor you have another calling. My FT Guinea Pig will make its 1st flite WITH differential thrust and rates of +/- 125%. I cannot wait! The Spektrum DX9 Manual was of no help. U made it so easy. Thank you, again!
@chrisstolle5664
5 жыл бұрын
I actually am a teacher!
@davehenry9039
5 жыл бұрын
Thanks brother just what I needed to know plain n simple 👍
@BrazenBullXXX
5 жыл бұрын
Thank you for the clear and coherent tutorial. I used it to program my large scale hovercraft!
@chrisstolle5664
5 жыл бұрын
Wow, that is cool!
@soghomog
4 жыл бұрын
I am building an RC boat with 2 EDF motors, it's a big boat... I found your explanation very clear and effective and to the point. I followed all of your steps and even made a cheat sheet for myself on how to do it again if I need to. I have one question, that I haven't figured out. Since one motor is connected to the throttle input on the receiver, and the other motor to the Aux1, so when i do "throttle cut" on my DX6, only the motor that is connected to the throttle input gets cut, the other motor still gets power. How can i program another switch to cut that motor that is attached to the Aux1 input on the receiver?
@iansummers6945
2 жыл бұрын
I’ve got the exact same issue🤔 Did you work it out?
@gryfandjane
8 жыл бұрын
Add another Sea Duck to the list! Thanks a lot for your walkthrough.
@chrisstolle5664
8 жыл бұрын
You bet! The Sea Duck looks like a ton of fun!
@elgage
7 жыл бұрын
Thank you very much. I was looking for this because I was making my own ft guinea pig. I made mine look like a coast guard c-130.
@chrisstolle5664
7 жыл бұрын
Thats cool. Any links? I would love to see that.
@elgage
7 жыл бұрын
Soon still getting the final decals on
@MrVerno1960
7 жыл бұрын
Excellent explanation on the set up..I am beginning my build soon on the FT Guinea Pig..thanks for posting it..
@danmccall3616
5 жыл бұрын
You just saved me countless hours!!!!! Thanks!! BTW, I like the way you just get to it, not a ton of BS!!!!
@chrisstolle5664
5 жыл бұрын
Thats kinda my deal bro. Glad it helped
@michaelbare5380
3 жыл бұрын
Thank you so much Chris. Just excellent. My Flight Test Kraken is almost ready thanks to you. One note. My DX6 did not have and Aux channel as changeable. Figured out that the FLAPS channel is the same thing. If anyone is having difficulties because they can't use the aux, just substitute the word FLAP for Aux and you should be fine. I think it is a firmware change since Chris created this video?
@demiurgiac
4 жыл бұрын
Wow... I can't thank you enough for this clear, concise lesson! You just save me a whole lot of frustration and confusion (LOL, apparently at the cost of a a whole lot of frustration and confusion on your part!
@chrisstolle5664
4 жыл бұрын
My pain is your gain!
@SeaPancakes1
7 жыл бұрын
Thanks for the help! I am planning on building the FT guinea pig and wanted to know how so set up differential thrust before I went and bought the electronics.
@bernarddostie8892
5 жыл бұрын
You are my saver! THANK YOU SOOOOO MUCH! I finally could setup my lovely Sea Duck. Couldn't find this info nowhere.
@chrisstolle5664
5 жыл бұрын
Glad this could help!
@TheM3MAN
9 ай бұрын
I have a new DX6 and followed your direction to differential thrust. For some reason both motors run with either left or right rudder.
@Jimgoodwin846
6 жыл бұрын
Thanks for this great video, you my friend are a great teacher. You made it simple.
@ddyodaman5515
7 жыл бұрын
Well done! Simplicity at its best
@chrisstolle5664
7 жыл бұрын
Thanks Dan!
@ericralston78
4 жыл бұрын
Great job, works with DX8e also. First try works perfectly!! With the 8ch I was able to keep the flaperons
@cobytenpenny5269
8 жыл бұрын
Great Video Chris! Just what I needed to finish my FT SeaDuck! You also have a very relaxing voice, you should consider a bedtime story channel haha!
@chrisstolle5664
8 жыл бұрын
Just got my waterproof foamboard to build a seaduck as well. Bedtime story channel, huh? I like it :)
@dutchloveRC
3 жыл бұрын
nice, simple , and slow enough for me to follow : )
@scottiniowa1
3 жыл бұрын
Thank you! Works great for a DX6e too.
@Havak37
6 жыл бұрын
Thanks for this. I have the DX6e and a sea duck in the mail. gunna be super easy slick thanks to your video.
@LyroLife
4 жыл бұрын
You are amazing, thank you a lot for the helpful video.
@rcjack522
5 жыл бұрын
Thank you so much I now have my jet flying beautifully
@chrisstolle5664
5 жыл бұрын
Glad it could help
@TactlessWookie
7 жыл бұрын
Awesome and simple. Hugely helpful.
@chrisstolle5664
7 жыл бұрын
Glad it helped.
@robdickinson4638
8 жыл бұрын
Thanks man. Your video is great. Really appreciate it.
@sherwoodp2738
5 жыл бұрын
Great explanation! Thanks for the video.
@diaryrecorded5524
3 жыл бұрын
3:50 is sOOooo my favorite part of this video because I say the same thing all the time haha THANK YOU FOR THIS VIDEO!!! "oh its beautiful! that took me so long to figure out because I'm not very smart" haha love it so much I dont know how to put my emotions into a yt comment
@chrisstolle5664
3 жыл бұрын
Glad I could brighten your day!
@diaryrecorded5524
3 жыл бұрын
@@chrisstolle5664 Yes sir! thanks for making a good video with good info and personality!
@xs-1b415
4 жыл бұрын
Great video, clear and concise!
@FloKoboi
4 жыл бұрын
this video is gold! thanks
@arpi7297
5 жыл бұрын
danke für das tolle Video , ist sehr verständlich und hilfreich TOP
@nestorgomez3718
3 жыл бұрын
Excelent tutorial man!!
@Asenjin
5 жыл бұрын
Thank you! This was incredibly helpful.
@johnknoy9955
4 жыл бұрын
Chris, just what I was looking for for a water rescue vessel!! Turns with differential thrust! Using a Gen 1 DX18. Now, how do I hook up a third brushless motor for a third motor to give me reverse capabilities(actually a forward thrust motor mounted backwards and will not engage until I flip a switch that turns off the differential motors and only turns on the reverse facing motor? Make sense? So far the water rescue craft works really well! Thanks, John
@zbugdiver
4 жыл бұрын
Very well done, thank you.
@papasplanes.956
Жыл бұрын
Not sure if you're still out there, but following your tutorial my motors are opposite of what you say I need. Left rudder gives me left motor power. Same for the right. Any suggestions would be greatly appreciated 🙂
@tonysilveira30
7 жыл бұрын
Very good video. You saved me my but. Works perfect. Thanks
@mattsrcking
6 жыл бұрын
Great video! Thanks for doing it
@TheGrubmiester
6 жыл бұрын
Good job, just set mine up and it works great, Thanks
@JoshWeaverRC
6 жыл бұрын
Nice. I may try the throttle instead of the mixing. I do want channel 6 to be higher though. Ch 6 will be an additional EDF that will be running even when the pusher prop is off and folded back. I need extra umph for a heavy load.
@JoshWeaverRC
6 жыл бұрын
Nice. Tied it in. Lowered the travel on Aux1. As I rolled lower than 99 the EDF sped up even with the throttle was off. Then as I hit the throttle it sped up as well. I suppose I could run EDF only and at full throttle either by rolling travel even lower or throttle cut. I would like my throttle to be that roller full time and my pan and tilt to be the left stick.
@Logan-ny1cl
2 жыл бұрын
Thank you very much you helped me
@excellenceinanimation960
5 жыл бұрын
Thankyou you have saved me!
@robtness1
2 жыл бұрын
And thanks for the great video!!!
@mattdroneon58
4 жыл бұрын
Outstanding explanation! Thanks!
@Barwell999
6 жыл бұрын
Ecellent job Sir. Thank you.
@skotman01
8 жыл бұрын
Great video! Hopefully I'll be able to use this for better ground handling on my hobby King c-47.
@chrisstolle5664
8 жыл бұрын
Glad you found it helpful.
@skotman01
8 жыл бұрын
+Chris Stolle I took it a step further bc I noticed that throttle cut only killed one motor. I can now kill either motor, or both allowing me single engine taxi. I'll do a video reply later.
@chrisstolle5664
8 жыл бұрын
I would be very interested in how you did a dual motor throttle cut.
@chrisstolle5664
8 жыл бұрын
Scott Heath I am very interested in how you did a dual motor throttle cut.
@zhang20244
Жыл бұрын
So cool , thank you so much 😊
@berndm9743
3 жыл бұрын
Great tutorial. Very clear and easy to follow. Thanks. My question is this....I have an HU16 Albatross twin and it can reverse by switching my gear switch. Will your differential setup work with my setup? I want the differential to help turn the plane when taxiing only. The water rudder is very inefficient in anything over a 3 mph breeze. Thanks!!
@williammcvea23
4 жыл бұрын
Could use some help. My throttle safety switch only works on the left motor not the right. Any idea as to how to configure so both work off same switch?
@plamenmishev3936
7 жыл бұрын
Well done! Thank you.
@AEROERGO
4 жыл бұрын
Thanks a lot! i forget how to do it !
@Sarge707
7 жыл бұрын
Great Video- Just set up my Guinea Pig by your Info BUT if I use Switch C for throttle cut it will only cut one engine- Guess you have to do something special to get a 2 engine throttle Cut? Great Job Again!!!
@chrisstolle5664
7 жыл бұрын
My only setback. I can't seem to figure double engine throttle cut.
@barnman73
5 жыл бұрын
@@chrisstolle5664 did you guys figure this one out? Setup went so smooth. I fear I am going to bite myself with this.
@jordanlavezzari6750
3 жыл бұрын
Ok, I’m not sure what I did but looks Functional on the radio but when I hook it up to the plane can’t seem to get the rotor to work one of the motors
@georgesager1573
Жыл бұрын
How do you get throttle hold to work on aux 1 throttle hold works great for the left motor
@chloe19815
4 жыл бұрын
This is great video how would you go about reverse for a twin screw boat. I build a bait boat and never finished it because i couldn't set up the mixing. Thanks
@jmacrcbuilds1103
Жыл бұрын
OMG thank you so much!
@icemans7
7 жыл бұрын
Question as I'm trying to wrap my head around differential thrust (dt). Spectrum radio. #1 is the rudder still used in combination with dt. #2 do you put it on a switch to be one or the other? #3 Rudder always on with dt. on a switch. #3 I think this would be most practical as I don't think I would used it that much other than to do some crazy spins. Thank you for your time.
@chriscrawford1958
4 жыл бұрын
This gets the differential working, but if you set up a Throttle Cut, it doesn’t cut the motor on Aux1. Any solution?
@MajDuty
5 жыл бұрын
Excellent. Thank you. Straight forward but: how do you set up Throttle Cut WITH Differential Thrust? Setting up Throttle cut as normal cuts only ONE motor. So how do you set Throttle Cut to cut BOTH motors?
@chrisstolle5664
5 жыл бұрын
I still havent figured that out. Sorry
@MajDuty
5 жыл бұрын
@@chrisstolle5664 , thank you for checking back. I almost had it. The trick was setting everything at -100%. This is what I learned with help: Set up a free mix as a kill mix: Throttle mix to Aux3 (where my 2nd motor is wired) -100% each way, offset at -100%. Set switch same as throttle cut. This mixes throttle against itself. Was used on older radios before throttle cut was available. Your video helped me get up to that point. Thank you.
Пікірлер: 219