Thats a snap ring plier, you'll probably be better off using a punch set
@beedleez3605
2 жыл бұрын
Does it work with metal pins? And transformers with metal pins?
@davidwhale8146
2 жыл бұрын
I've never worked with Transformers, but it will all depend in the type of plastic they use (whether it will soften under heat) and how the pins are engineered (whether they have something internal keeping then in place, unlike these).
@diarykhaynara7014
Жыл бұрын
Yes...i see
@johnsafley8078
2 жыл бұрын
Thank u so much
@harryprice8552
2 жыл бұрын
Thanks, man. Simple and informative
@silaso-ren2857
3 жыл бұрын
Great video man, what figure is this? Looks perfect for a project I want to do :)
@davidwhale8146
3 жыл бұрын
This is the Marvel Legends Ulysses Klau from Black Panther
@silaso-ren2857
3 жыл бұрын
@@davidwhale8146 - Thank you very much, I like your vids man. You have earned a subscriber, decent figure custom channels are hard to come by these days.
@davidwhale8146
3 жыл бұрын
@@silaso-ren2857 thanks, I appreciate it!
@jayplaytv0840
Жыл бұрын
funny enough here I am making a chainsaw man figure and this body looks perfect for the base haha
@cobra4life324
Жыл бұрын
Nice video question does this work on g.i. Joe classified as well
@davidwhale8146
Жыл бұрын
Yes, it should work on any figure with pin joints.
@Therealayiaziii
Жыл бұрын
This action figure pin just fucking declines to go through the joint
@tophottaboy5556
Жыл бұрын
What about Disassembling a body like ulysses klaw that you have? Do i need a boormachine? 04:44 but the way how do I find such a thing on Amazon?
@davidwhale8146
Жыл бұрын
If you mean disassembling the torso, you would need to crack it open at the seams. There are a few ways to do this - if you search "cracking Marvel Legends torso" on KZitem, you should be able to find a couple tutorials.
@cristianojeda2418
3 жыл бұрын
What about painless joints?
@davidwhale8146
3 жыл бұрын
Sorry, no idea - I've never disassembled a painless joint.
@lazyhydroponicsandstuff3682
2 жыл бұрын
There is no such thing as a Painless joint. You'll find that out when you get older lol
@austinreed7343
2 жыл бұрын
@@davidwhale8146 I think it’s “pinless”
@777heartsdesire
Жыл бұрын
Where can I buy these
@pierresu4723
7 ай бұрын
I can't put it back in😐
@davidwhale8146
6 ай бұрын
Make sure you heat up the leg again and that you're putting the narrow end in first.
@pierresu4723
6 ай бұрын
@@davidwhale8146 I did this a few time but this figure the hole doesn't aline and the peg have the same size on both end so I couldn't put it back in, and than I messed up when heating and it melted 😭
@Vander101
6 ай бұрын
I'm having the same problem with movie stormshadow. Pegs are same in both ends but can't get back in my thumbs and fingers are raw now from trying. I've heard many times no go on it
@peanaut_ayk3644
5 ай бұрын
@@Vander101 any updates?
@MrCros1970
2 жыл бұрын
Cool, thank you
@SpaceAcex
Жыл бұрын
Thanks for this. Been wanting to fix some of hasbro’s mistakes on a few of my figures but been nervous to damage them. This is super helpful
@mr.joshua204
Жыл бұрын
I use the same process, but instead of water, I use my wives hair dryer. It's quicker and you don't have to worry about having wet plastic slipping out of your hand, and accidentally slicing your hand open
Пікірлер: 30