I approve this works. Used 7.5V power supply, 470uF capacitor and not original canon battery. Had to shorten in a bit different spot, because PCB was a bit different. Nice video
@GraphicManInnovations
2 жыл бұрын
thanks, but what is the point for the capacitor? the charger is already providing clean enough dc voltage right? also is the pcb necessary? it wont work with just +ve and -ve? hope to hear from u
@donmarciano1981
2 жыл бұрын
Capacitor helps provide stable voltage especially with long cable. When camera drain lot of power (movie, starting) volatge can drop below proper value. Capacitor is a local energy reservoir and it is cheap so we have more pros than cons.
@GraphicManInnovations
2 жыл бұрын
@@donmarciano1981 got you, but what about the internal pcb, it is the cels bms, can it be removed entirely, or did u just bypassed it ?
@jozafax
8 жыл бұрын
Nice video. I want to make an adapter for my 80D. There is a contact in the camera for the C terminal on the original battery. Do you happen to know the function of this terminal?
@donmarciano1981
8 жыл бұрын
jozafax Use google www translator and go here atstudiota.exblog.jp/14982028
@jozafax
8 жыл бұрын
Thank you.
@MrQuelux
3 жыл бұрын
a z ciekawości po co ten kondensator ? czy przy napięciu np 7,2V będzie on potrzebny ?
@donmarciano1981
3 жыл бұрын
Najbliższy kondensator filtrujący jest w zasilaczu przy gniazdku a później długi kabel i na samym końcu przydałoby się coś wygładzającego/filtrującego. Na pewno nie zaszkodzi.
@NoorulIslamCenterForEducation
6 жыл бұрын
You’re tablet using software name
@samsystems8191
4 жыл бұрын
Canon 200D compatible for This adapter
@debojitacharjee
8 жыл бұрын
i want to know how do i know the amps of a battery if i want to power any electronic device intead of a power adapter. For example if a device needs 3v 0.4 A power adapter then how am i going to know how many amps two AA 1.5 v battries are going to give if connected in series? I know that in series both of them will give 3v but how do i know about the amps because all types of batteries are not having same ampere hour ratings!
@donmarciano1981
8 жыл бұрын
1 amp will be OK. The bigger current cause less cell's life. Remeber that every cell has its internal resistance. It will cut off your maximum current. To draw more current you should use cell with less resistance like bigger 1,5V battery - for example: LR14Check this website: www.candlepowerforums.com/vb/showthread.php?64660-Alkaline-Battery-Shoot-Out
@habitante19
3 жыл бұрын
I cannot get this to work. I've seen a lot of videos doing the same, all I get when I turn on my camera is "Change battery" error.
@BirdsBoxTV
3 жыл бұрын
Voltage to low?
@BirdsBoxTV
3 жыл бұрын
A u mnie w 550D nie działa. Za cholerę. Podałem napięcie 7.5V na styki wybebeszonej baterii - napięcie jest na 100%. Pomimo tego aparat się nie uruchamia. Z normalną baterią pracuje. Z tą fejkową - nie. Czy przypadkiem aparat nie rozpoznaje obecności baterii trzecim stykiem który jest w komorze aparatu?
@donmarciano1981
3 жыл бұрын
Klapka została prawidłowo zamknięta? Przewód musi przechodzić przez dziurkę zasłoniętą gumką
@BirdsBoxTV
3 жыл бұрын
@@donmarciano1981 Oczywiście :)
@donmarciano1981
2 жыл бұрын
@@BirdsBoxTV Daj kondensator. Wiem, że bez niego niektórzy mieli problem z większymi impulsami prądu - np. przy starcie lub przejściu na liveview
@BirdsBoxTV
2 жыл бұрын
@@donmarciano1981 Zastosowałem przetwornicę o większej wydajności prądowej i problem zniknął :)
@hridoybilash8613
4 жыл бұрын
Where to find it. plz tale me
@257acu
6 жыл бұрын
please. can i use an adapter with 2A ?
@donmarciano1981
6 жыл бұрын
lloyd Films Of course. Voltage is crucial.
@257acu
6 жыл бұрын
thank you. but problem is that his outpout is 9Volt , 2A. i can use it?
@donmarciano1981
6 жыл бұрын
9V is too high. You can use diodes to reduce voltage but I think it is still too high value.
@ybnybn-vp2us
6 жыл бұрын
Czesc, nie włącza mi się 550d co byś zrobił na moim miejscu? Tam gdzie się baterie wkłada są 3 blaszki nie powinno ich tam być 4? Tutaj zdjecie jak wyglada moj aparat w srodku: ibb.co/mx3yWS
@donmarciano1981
6 жыл бұрын
Nie otwiera się fotka. Pamiętaj, że aparat włączy się tylko jeśli klapka od baterii będzie zamknięta lub coś co ją imituje. Jeśli tu jest problem, to się nie uruchomi. Jak się wysuwa klapkę na kartę SD i ją ponownie zasuwa to miga dioda power?
@ybnybn-vp2us
6 жыл бұрын
photos.google.com/photo/AF1QipPln7ip2x7PjUp0uOdiuSy5ceEvIMryXNjGi5BT?hl=pl dioda nie miga, kiedys tez mialem taki problem i wyjecie i wlozenie karty SD pomoglo teraz nic nie pomaga
Пікірлер: 30