Joe Martin, thank you so much for your tutorial, it helped me a lot with my DJI Mini 2. As a contribution to your video: The Mini 2 code is the same as the Mavic Mini (WM160). In order for the COM port to remain open, it is necessary to install DJI Assistant 2, wait for the drone to be recognized by the software, and then close DJI Assistant 2. After that, the COM port will remain open.
@JoeMartinMVC
Жыл бұрын
Thank you for the information, that should help a lot of Mini and Mini2 owners.
@eliezersqr
Жыл бұрын
Thanks man! Useful information!
@eliezersqr
Жыл бұрын
Joe and Greg, your information working perfectly. Now I just have the alert codes 40011 and 40021, but I can fly and all works. Do you know how to clear the alert codes? Somewhere I read about a Dji special software, but I didn't find it... Again, thanks for help!
@JoeMartinMVC
Жыл бұрын
@@eliezersqr Unfortunately that special DJI software is one that authorized repair centers have and requires a connection to their servers to use. We haven't been able to get a copy of it that can be used by us yet.
@eliezersqr
Жыл бұрын
@@JoeMartinMVC :( sad... Greetings from Brazil! Nice channel, thanks man!
@coryhiatt9152
3 ай бұрын
I am working in the DRC Congo, and had to replace my gimbal, installed it, and it needed calibration, I thought I was going to have to take it back to the states and hire someone to calibrate it for me, but I watched your video, and was able to calibrate the gimbal, thank you so much for the time and effort to put this video up, it saved me a ton!
@calebgeorgeson4526
3 ай бұрын
God bless you, it's 1 in the morning right now and I was about to give up my calibration efforts when I found this video. My gimble is now straighter than I am. Thanks a million!
@VlogCity
3 ай бұрын
Bro this is the 4th video I've run through, and it's the only one that worked. Thank you so much for your clarity and help!
@robertojustus8567
Жыл бұрын
Amazing video, thanks for this, i broke my grandpa's drone and as it turns out it was thankfully only the gimbal assembly, the camera was working normally, and they charge a lot of money just replacing the parts, i could only afford the gimbal, not both, you saved me
@valkyrie9884
12 күн бұрын
Thanks for posting the solution. Tried it, the gimbal didn;t move at all after entering the command into the cmd prompt. Worked anyway, by the looks of it. Gimbal no longer stays in weird position (almost every time it got stuck in a different position or started shaking). So, if it helps to someone with the same issue, this was my procedure: 1. Download/install everything. 2. Connect the drone to PC. 3. Note the com port. 4. Run the command lines in CMD prompt. 5. Wait a minute. 6. Switch off and back on the drone. Tested it out multiple times today and the error doesn't show up in the app anymore - both when drone switched on, but still on the ground and when flying (windy day today).
@rukospb
Жыл бұрын
Joe Martin, thank you so much for your tutorial, it helped me a lot with my DJI Air 2S!
Жыл бұрын
What is the code for air2s ? Same as air2 ?
@thinhphamfoto2426
3 ай бұрын
did you got any error when running?
@louismattes1135
6 күн бұрын
Unfortunaltly my gimbal stays a little displaced on my Air2S
@BigDShakes21Gators
2 жыл бұрын
An amazing step by step … well explained … you killed it … I appreciate the tutorial. Great job
@JoeMartinMVC
2 жыл бұрын
Thank you!
@wadrian706
Жыл бұрын
Man I've watched all these other videos and they seem to go so fast to everything and leave out steps I think they do it perfectly just to screw you up in the process of fixing your camera on your drone I watch your video one time and I've already made it to the whole process I would like to give you a big shout out and thank you so much for making shit simple
@JoeMartinMVC
Жыл бұрын
Thank you!
@F15cCrewdawg
2 жыл бұрын
To avoid all of the error codes you can swap the camera sensor from the old gimbal to the new one (it's 2 small screws on the sides of the camera). You will still have a calibration error (the gimbal will auto calibrate with no issue) but the other errors will still show up as the motors are paired with the drone but you won't have the imu errors. If you figure out how to get rid of the calibration error that would be fantastic but this is better than having all of them. I don't think I have tried the python calibration after the sensor swap but that may clear it, but I know for sure that the imu codes won't show up with the original camera. Obviously if this isn't possible then the only current option is to send it to dji and have them clear the codes.
@umairhafeez
Жыл бұрын
Hey Kevin I crashed my DJI Air 2s after which I had to replace the Gimbal and left rear leg. The repair was successful but the infamous 40011 error remained. I flew the drone for new minutes but there were some funky movements by the drone and IMU error showed up and I immediately landed the drone. I tried calibrating the IMU but it kept getting stuck at 6% and then it throws calibration error. Right now the errors on the drone are Gimbal calibration error 40011, IMU not calibrated. Calibrate IMU 30055, IMU calibration incomplete. Recalibrate IMU 30056. I have replaced the IMU, GPS module and GPS flex cable but the issue remains. From your comment, I feel as if the error is software related. Can you give some guidance please.
@X9Adventures
Жыл бұрын
Do you have a video for this replacement?
@wadrian706
Жыл бұрын
Will that work on the mavic air 2???
@F15cCrewdawg
Жыл бұрын
@@wadrian706 Yes this will work on the air2 but not the 2S
@F15cCrewdawg
Жыл бұрын
@umairhafeez sorry for the delayed response on this but you can calibrate the gimbal with python and then should do an imu calibration and firmware refresh. The error codes will not go away unfortunately
@patlinn5296
Жыл бұрын
Thank you so much!! I followed another set or instructions on YT and it didn't work. Your instructions were very easy to follow.
@michaeltrager4381
Жыл бұрын
Thank you Joe Martin:) Your presentation was the best and easiest to follow after hours trying others!!! My Camera/ Gimbal is now centered and working great:)
@JoeMartinMVC
Жыл бұрын
I'm glad to hear so!
@joseaugustosantaella4253
6 ай бұрын
😃Thanks a lot Joe!!!!!! You saved my drone!!!! 🙏God bless you 😉
@dronestockclips6697
2 жыл бұрын
You're amazing.. I've been watching lots of videos how to get this to work. I nearly gave up until I found this your video. Now my mavic air 2 is fixed after following your steps. Thanks for this. I'm a subscriber
@JoeMartinMVC
2 жыл бұрын
I'm glad I was able to help!
@chalmersrogers9890
2 жыл бұрын
This was perfect. After following your directions I got error 40011 I cleared it by recalibrateing on my smart controller 👍
@JoeMartinMVC
2 жыл бұрын
Oh? That REALLY tempts me to pick one up to see how it clears the codes. Just a lot of money to do that.
@igori86
2 жыл бұрын
I have also got this error 40011 after doing this and can't to clear it with calibrating with smart controller. How are you done that?
@Matanumi
Жыл бұрын
maybe he had the OG gimbal to his drone that he was fixing
@bacheandopy
Жыл бұрын
Excelente amigo! lo probe hoy en mi DJI AIR 2S y de maravillas, muy bien explicado el video! recomendado 100% Saludos desde Paraguay
@wilson24p
Жыл бұрын
what code for air 2s?
@aaraujo1605
Жыл бұрын
@@wilson24p WM232 = 28 # Released 2021-04-15 (MAVIC) AIR 2S
@jhonnatanlipe8832
3 ай бұрын
Bro! acabas de hacer a un hombre muy feliz! Muchas gracias por el tutorial, héroe sin capa!
@jefferymelochick6558
Жыл бұрын
what to do if python doesnt move passed the first calibration step? the gimbal isnt moving and python wont update with a new imput line
@adnanalshami2469
Жыл бұрын
Hi i did everything but I couldn't find my mini 3 pro code neither in Google search so how do we get past this issue kindly reply as am stuck here with cross eye drone 😢 appetite the tutorial session it was much helpful
@pixelsreflected2788
Жыл бұрын
Thank you very much sir, this work perfectly...i knew it had to have a reason the gimble was spinning like crazy...lol
@JoeMartinMVC
Жыл бұрын
Glad I was able to help out!
@Tayriz_
4 ай бұрын
Thanks for the video ! and for the Mavic mini 3 pro the code is WM162
@santitomich
5 ай бұрын
thanks, this hack saved my life
@gavinohara9342
3 ай бұрын
thank you , legend ! - mavic air 2
@FlynFlash
2 жыл бұрын
repaired mavic 2 pro camera thank you for your great video
@matiinaustralia7654
Жыл бұрын
Thanks a lot!!!! my Mavic Mini is back to life!!!!! Using litchi I dont have any alert!
@JoeMartinMVC
Жыл бұрын
That's wonderful!
@devingeis3094
9 ай бұрын
The 1st command works, the 2nd command says it will take about 30 seconds ect but it doesn’t move or do anything. It says unrecognized response. My gimble is still tilted to the left a little after doing the first command. I’m going on vacation in 2 weeks and I need my drone fixed
@NotBurner
Ай бұрын
anyone know if this can be done for the mini 4 pro after replacing the whole gimbal camera assembly ? what code should be used ?
@hassanalabadi7344
Жыл бұрын
thanxx for that great explanation ..... but im getting that error (Error: could not open port 'COM3': PermissionError(13, 'Access is denied.', None, 5) ) any idea how to solve it ??
@11voldis
5 ай бұрын
It worked, finally a good video 🎉
@RiksC80
Жыл бұрын
By any chance...do you have the code for de mavic mini 3 pro?
@willieleniek
2 жыл бұрын
Very nice tutorial... straight forward.
@JoeMartinMVC
2 жыл бұрын
Thank you!
@MrYovilleSTAFF
2 жыл бұрын
Thank you for making this tutorial!! I have zero computer skills and yet I was still able to follow along. Worked like a charm!! Thanks again
@JoeMartinMVC
2 жыл бұрын
I'm glad I was able to help out!
@mohammedullah3338
Жыл бұрын
I got a error message saying "Error: could not open port 'com3': PermissionError(13, 'Access is denied.', None, 5)" Please Help!
@estebanbuenano9345
2 жыл бұрын
You're a master!! Great Video. Thanks
@JoeMartinMVC
2 жыл бұрын
Thank you!
@gerardoortiz6464
2 жыл бұрын
Thanks, works fine in a mac m1 with parallels, Thanks a lot!
@bondisurfrescue
Жыл бұрын
hey i have a mac and in depserpate need of help with this, could you reply with your contact details so I can ask you a few questions? Thanks
@zingaFPV
Жыл бұрын
In the cmd I receive the error Error: could not open port 'com6': PermissionError(13, 'Access is denied.', None, 5) Somebody did manage to solve it?
@jon-robertsbuehler6628
11 ай бұрын
Hi, I just fixed this error I can't find the post but I had the DJI Assistant opened and after i closed it I tried the script again and it ran
@nickheath7733
16 күн бұрын
I did everything exactly and the gimbal doesn't move. I can see the feed on my remote but it doesn't recognize the gimbal and I can't move the gimbal from the remote. This program also does not move the gimbal. Do you know what it could be?
@mattweber6505
6 күн бұрын
Cmd prompt tells me port bulk is required. I figured it is a data cable issue. Swapped cables and I got no difference. This was a lot to go through only to fail and nothing happened. I’ve tried your video and Howfixit neither worked for me.
@pgchem
Жыл бұрын
Its not work for me i cant find DJI MINI 3 have you solution for that?
@MuhammadDJI
Жыл бұрын
do you have a code for dji mini 3 pro
@user-sd4pv6bc8v
5 ай бұрын
Hi. I can calibrate
@pascalou3000
Ай бұрын
how do you open port com. only com 3 is showing. when put in command string, get Error: could not open port 'COM2': FileNotFoundError(2, 'The system cannot find the file specified.', None, 2)
@LouiDali
Жыл бұрын
is there a code for the mini 3 pro or no?
@zoomdigitalLive
9 ай бұрын
i search too
@ChuckandZee
2 жыл бұрын
Appreciate it! Helped a ton. Subscribed. Looking for to seeing how to fix the error (that you get after following this process). Thanks!
@JoeMartinMVC
2 жыл бұрын
Thank you! I know how to fix it, but it requires a tool that only DJI has that requires server authentication to be able to use it, so I'm trying to see if there's any way or groups that have found a way to bypass that. Hopefully we get something soon.
@FrizoDrone
2 жыл бұрын
@@JoeMartinMVC olá conseguiu resolver esse problema? agradeço muito a ajuda
@JoeMartinMVC
2 жыл бұрын
@@FrizoDrone Sadly, still no luck on the tool becoming usable by us. However I have heard reports of the Smart Controller being able to clear the errors. I want to try it, but don't have the funds to buy one just to see if it works.
@luiskantek
Жыл бұрын
Hi there, my drone is mini 3 pro. ive just changed the gimbal. after closing the camera keep lookimg right. The mini 3 pro have calibration direct on control. is not the same? may i have to do your instruction or change the camera?
@Santiagoslawncare
3 ай бұрын
Does work with Apple air Mac’s ?I can’t seem to be getting the same results and information as you do
@mattrommel2461
Жыл бұрын
I'm stuck in translating the comm port section and command prompts in terminal. Making sure I translate this correctly for Mac.
@TheBoringReason
2 жыл бұрын
Perfekt. I got a mini 1 im gonna repair well not mine. But i gotta change the gimbal. So that might be really usefull
@fadhilmarzuki8284
9 ай бұрын
why i got this thread? please help me... C:\dji>py setup.py install Traceback (most recent call last): File "C:\dji\setup.py", line 17, in from setuptools import setup ModuleNotFoundError: No module named 'setuptools' During handling of the above exception, another exception occurred: Traceback (most recent call last): File "C:\dji\setup.py", line 19, in from distutils.core import setup ModuleNotFoundError: No module named 'distutils'
@iDannyRed
Ай бұрын
Tengo el mismo problema, pudiste solucionarlo?
@angelmontes1734
2 жыл бұрын
Followed all steps. Got to the point where COM3 would only appear for a few seconds and then the drone would disconnect. COM3 only stays when I open DJI assistant 2. Upon starting the calibration on command prompt, it will say access denied. However, I close Dji assistant 2, COM 3 stays, Unrecognized response to calibration… appears, but drone does nothing at all.
@JoeMartinMVC
2 жыл бұрын
When you're opening your command prompt are you running it as administrator, or just opening it regularly? Normally it only gives "Access Denied" if it's a regular permission command prompt and not an Administrator Command Prompt.
@HonestEvolution795
3 ай бұрын
So on my computer my drone is coming up as a USB G drive. how do i type that in the command prompt?
@lightningquads2446
Жыл бұрын
Hi, I´ve had several problems to get the script running. My solution was: instead of writting " py ....... " i had to type "python ...... " for each command. Then everything worked just fine! System : Win10
@umairhafeez
Жыл бұрын
Hey, thanks for the video. My story is that I crashed my DJI Air 2s after which I had to replace the Gimbal and left rear leg. The repair was successful but the infamous 40011 error remained. I flew the drone for new minutes but there were some funky movements by the drone and an IMU error showed up and I immediately landed the drone. I tried calibrating the IMU but it kept getting stuck at 6% and then it throws a calibration error. Right now the errors on the drone are Gimbal calibration error 40011, IMU not calibrated. Calibrate IMU 30055, IMU calibration incomplete. Recalibrate IMU 30056. I have replaced the IMU, GPS module and GPS flex cable but the issue remains. From your comment, I feel as if the error is software related. Can you give some guidance please?
@stevemcgowan3017
4 ай бұрын
after typed in code to command line i don’t think wm231 is in file i downloaded think need download another dji file
@stuartgoodall9592
3 ай бұрын
I cant get all the way to the cmd lines and it says that there is not file folder for Python. can you assist
@mr.Plexus
5 ай бұрын
Hi, thank you for your tutorial. I got a question and need your help. I do everything the same. But when I paste the second command, nothing happens with my mavic air 2.
@jimmakos1976
18 күн бұрын
hi. thanks for sharing. DJI Mini 4 what code has?
@aerialview3342
Жыл бұрын
Does this process works for mini 3 pro?
@zdenekmach4258
7 ай бұрын
Have you tried it? Does it work for Mini3 Pro?
@akikulislam5261
Жыл бұрын
your video very helpful. Thank you so much
@JoeMartinMVC
Жыл бұрын
Thank you.
@akikulislam5261
Жыл бұрын
boss, dji mini 2 remote controller not working, not open not charging, any solution?
@JoeMartinMVC
Жыл бұрын
@@akikulislam5261 Sounds like your main logic board is bad if nothing is working and it's not charging.
@mattrommel2461
Жыл бұрын
Really wish there was more clear instructions for mac.
@vasu06mobile
2 жыл бұрын
excellent work bro thanks for the work
@JoeMartinMVC
2 жыл бұрын
Thank you!
@vandantandel3761
11 ай бұрын
I have the dji mini 3 pro should i use the mavic mini code?
@TechstoreTechnician
2 ай бұрын
Mini 4 Pro Code?
@eprohoda
2 жыл бұрын
JoeMarinMVC!Like it! very amazing done, ))
@JoeMartinMVC
2 жыл бұрын
Thank you!
@andresbarboza6667
Жыл бұрын
It work for a dji mini 3 pro?
@19sloper
7 ай бұрын
When I go to Device Manager to see the port, there is no "Ports" item listed. I have Windows 11. What now?
@SimonLiegeoisOfficiel
2 ай бұрын
Merci, ça marche ! au top
@someniceguyz
3 ай бұрын
Hi! Thank you for tutorial. May I ask you does it work with mini 3 pro? And what code for this drone should I use? Thank you
@lizabigailcaceres5600
5 ай бұрын
I have the issue like my gimbal is centered in correctly
@clist9406
Жыл бұрын
Very useful information, many thanks . I hit the like and subscribe already
@JoeMartinMVC
Жыл бұрын
Thank you!
@jac2206
Жыл бұрын
Thank you so much
@XavierBaker
19 күн бұрын
Is there a command to calibrate the Vision sensors?
@dammecine
5 ай бұрын
I CAN'T FIND THE COM PORT IN DEVICE MANAGER
@RobertAlarcon-vb6vb
Жыл бұрын
Hi, I've tried everything 3 times. I keep getting the message below. Any suggestions would be greatly appreciated. python was not found; run without arguments to install from the Microsoft Store, or disable this shortcut from settings > Manage App Execution Aliases
@RooflessCat
7 ай бұрын
same here :/
@angelacarrara5541
10 ай бұрын
Need you help please I’m missing a step got to the black screen. It’s not reading the com
@photosolutions3271
Жыл бұрын
Hi, I got a problem , during the calibration my gimbal turns 180 degree into the drone body and every start of the drone it keeps doing that (Mavic 2 pro)
@ElAngelDelCorridoYSusPlebes
Жыл бұрын
Del dji mini 3 pro cual seria el codigo
@andreeklundh6058
Жыл бұрын
Hello. Thanx for the video. I’m wondering what code I should use for DJI air 2s (not mavic)? / André
@Strix69420
Жыл бұрын
how do you know if your dji mini 2 needs this my gimbal says its stuck but moves fine
@haycall
3 ай бұрын
Hi there. I have DJY Mini 3 pro Model RM330. In the Command Prompt I replaced the model with my RM330 but it doesn't do anything after the 'GimbalCalib JointCourse' command. The camera is not moving, and the Command Prompt is not giving an Error message. Do you know what am I missing here?
@he4vym3t4l
2 жыл бұрын
Thank you for the helpful video. I’m having trouble and can’t find anywhere where this is addressed. I can run the first JointCoarse command just fine and the drone will run through its motions. But when I run the second LinearHall command the drone does not respond. I’ve tried a few things others have suggested like turning the drone off & on between commands but still am having this issue. Any ideas that might could help?
@JoeMartinMVC
2 жыл бұрын
I can't say I have much to offer there if it's not responding to the command unfortunately. How far off is the gimbal still after the JointCoarse command?
@chouchenwejden4499
Жыл бұрын
Hi Alex, I got the same problem, did you find any solution?
@canihavemore7416
Жыл бұрын
@@chouchenwejden4499 Hey mate, same issue. Did you guys find a solution?
@brettwallace7327
10 ай бұрын
I've got the same issue on the Air 2S
@LeXro6
6 ай бұрын
I have the same problem on the mini 2
@shannonlandsaw1844
2 жыл бұрын
Hello! Thanks for the video, I’ve been able to get through every step successfully for my mavic air 2 except the last command prompt. After the first one finishes and the second one is entered my drone does nothing. Gimble is still setting at an angle horizontally and most of the time the camera points downward. The camera moves on all three axis during start up. Thanks for your help!
@JoeMartinMVC
2 жыл бұрын
Is there any error message that comes up when you try to run the second command? Besides the standard error that pops up for both commands.
@bumpsy2358
Жыл бұрын
@@JoeMartinMVC I have the same problem and no only the command not recognized error that happens on both commands
@peterfitopoulos765
Жыл бұрын
Hi did you ever solve the issue?
@chouchenwejden4499
Жыл бұрын
@@JoeMartinMVC I got the same problem, after completing the JoinCoarse command, the LinearHall doesn't do any effect on the gimbal even so a message saying the gimbal would took 30s to calibrate. I didn't get any special error beside the standard one. PLEASE HELP.
@a6mzero474
Жыл бұрын
@@JoeMartinMVCi have the same problem with my dji mini got anybody a solution?
@pierre-lucdoiron1325
Жыл бұрын
I must be doing something wrong since the 5 different computer I tried wont show a Com port after following all the steps.
@jeffersonbezerra1980
Жыл бұрын
Já existe para mavic mini 3?
@Juniorbahia
Жыл бұрын
Gostaria de saber pro mini 3 pró
@LeXro6
6 ай бұрын
i have the mini 2 but when i type in the joint coarse request it gives me this error No response on calibration command JointCoarse request. And the com port im not sure which one it is because its still there even when i unplug the drone. any helps?
@user-ud7bp7kd2n
Жыл бұрын
Mini 2 I have the first step working however the second step doesn’t initiate. Any thoughts?
@EldosReciyev
11 ай бұрын
Hi.For me, the drone is detected in the USB port. How should I write the code? I would be happy if you help me.
@batuhansygn
Жыл бұрын
Do we have to install the software even after unplugging and plugging in the flex cable? I just changed a plastic part. But now the gimbal doesn't turn left or right. My device Mavic 3 Classic
@dammecine
5 ай бұрын
PLEASE HELP! I CAN'T FIND THE COM PORT IN DEVICE MANAGER
@guilletarthur746
Жыл бұрын
Hi ! I have a probleme, the first command works perfectly, but the second do nothing... Auto calibration on the app is stucked a 0%, any idea ? Thanks a lot !
@jessicaandtrains7768
2 жыл бұрын
Can anyone please confirm that they've calibrated a mini 2? I've fitted a new gimbal and I can't get it to work at all. Have kept\transplanted the original camera
@enumamedia
9 ай бұрын
after video ı have this error code: Unrecognized response to calibration command JointCoarse request.
@disa18ct
2 жыл бұрын
I have a mac book is their a video on how to do this on a mac book?
@JoeMartinMVC
2 жыл бұрын
Boot Camp on Mac to load in to Windows and then do the windows version of the steps. I don't have a Mac to test it with for a mac-specific solution.
@disa18ct
2 жыл бұрын
@@JoeMartinMVC thank you for the reply I will try that
@disa18ct
2 жыл бұрын
@@JoeMartinMVC it worked thank you so much!! It was super easy video, thank you for making it so easy and detailed.
@JoeMartinMVC
2 жыл бұрын
@@disa18ct Perfect! I'm glad to hear it worked out well for you.
@arielleandbenleisman507
Жыл бұрын
@@disa18ctI also have a MAC, how did you get around the 7zip program being for PC only?
@FPVFRASHA
8 ай бұрын
hey! i have the camera calibrate error and wont let me record footage from the drone either now only from the goggles in my dji fpv drone after i changed the gimble to another onei looked at that python way to calibrate the gimble but it doesnt say it supports my dji fpv drone:( does anyone have any ideo of what i can do to fix it please? its so annoying as i use it for capturing footage:(
@TuManWorld
Жыл бұрын
I dont have USB serial Device in my Device manager. What to do then? I have Mavic Mini and I see my drone only as Mass Storage Device
@JoeMartinMVC
Жыл бұрын
The Mini 2 code is the same as the Mavic Mini (WM160). In order for the COM port to remain open, it is necessary to install DJI Assistant 2, wait for the drone to be recognized by the software, and then close DJI Assistant 2. After that, the COM port will remain open.
@urbexcouple
4 ай бұрын
Would you need to do this tho if im using my original camera and back of the camera?
@johndraveyyt6730
3 ай бұрын
Can you use this for callibrating DJI mini 3?
@dronesetc9769
Жыл бұрын
I had to install python 3.10.9 version 3.11 didn't play well with the scripts, tried on two laptops . If you get a Python not found error, uninstall python and install an older version
@brettwallace7327
10 ай бұрын
Thanks for this tutorial. Crashed my Air 2S a few weeks ago. I'm trying to diagnose what's wrong with my gimbal since I have a video feed but I cannot calibrate or move the gimbal with the remote. The first command works for me. But the gimbal is unresponsive to LinearHall. I suppose I need to do a teardown and find out what hardware is broken. At first glance the ribbons look OK. Any suggestions?
@triadretailconstruction558
2 ай бұрын
Hi, I'm experiencing the same issue on an Air 2S. Did you find a solution for this problem? Thanks.
@brettwallace7327
2 ай бұрын
@@triadretailconstruction558 I tried, but ended up sending mine back to DJI for repair. Money well spent. They fixed and sent it back.
@ladorani-cx4xf
Ай бұрын
same. problem. my. dji air 3. how. to. solved
@shahriarfahim9796
9 ай бұрын
I followed all the procedures you showed. But my computer gives me a message. py is not recognized as an internal or external command, after that I selected the path in edit the system environment even after that it shows the same py is not recognized as an internal or external command, I want help in this matter? Now how do I do the gimbal celebration?
@Jared.Elliott
6 ай бұрын
Replace the “py” with python or python3, python3 worked for me, just at the beginning of of each line
Пікірлер: 540