I built another multisensor for the bedroom and I decided to change up a few components. Dive in and take a step by step approach to build it with Otto Winter's ESPHome software this time around as it's been a year since I built the initial Bruh Automation version. ESPHome is easy to use and configure; No Arduino IDE, no coding, just a config file and the sensors wired up!
⚡Parts Used⚡
NodeMCU - geni.us/fn4BL
TSL2561 LUX Sensor - geni.us/Uef8mzV
Jumper Wires - geni.us/d3r9O
AM312 Motion Sensor - geni.us/OiewrL3
5mm Neopixel - geni.us/go3Gk25 or 8mm Neopixel - geni.us/kninEgN
DHT22 Temp/Humidity - geni.us/v3jPH
Dive into the fun world of 3D printing! geni.us/0hId2
⚡Products We Use/Recommend⚡
Amazon US - amzn.to/2YZNDeO
Amazon UK - amzn.to/2TnG2R4
Amazon CA - amzn.to/2JWsNq5
⚡Be Social!⚡
Main Website - www.digiblur.com
Discord Chat - discord.digibl...
Patreon - patreon.digibl...
Facebook - facebook.digib...
Instagram - instagram.digi...
Please note, the product links above could be affiliate links, using them could earn digiblurDIY a small commission of most purchases and helps with future video projects. Thank you!
Sample ESPHome YAML (replace the IP address and WiFi information)
esphome:
name: sensor_node1
platform: ESP8266
board: nodemcuv2
wifi:
ssid: 'yourWIFIhere'
password: 'yourPASShere'
manual_ip:
static_ip: 10.10.1.40 change this IP and remove this message
gateway: 10.10.1.1
subnet: 255.255.255.0
dns1: 10.10.1.1
dns2: 10.10.1.1
Enable logging
logger:
Enable Home Assistant API
api:
ota:
sensor:
platform: dht
pin: D7
model: dht22
temperature:
name: "SenseNode Temp"
humidity:
name: "SenseNode Humidity"
update_interval: 30s
platform: tsl2561
name: "SenseNode LUX"
address: 0x39
update_interval: 5s
binary_sensor:
platform: gpio
pin: D6
name: "SenseNode Motion"
device_class: motion
on_press:
then:
light.turn_on: ESPD4led
on_release:
then:
light.turn_off: ESPD4led
light:
platform: neopixelbus
type: RGB
variant: WS2811
pin: D3
num_leds: 1
name: "SenseNode LED"
platform: binary
name: "SenseNode D4Led"
output: D4led
id: ESPD4led
i2c:
sda: D2
scl: D1
scan: False
output:
platform: gpio
pin: D4
id: D4led
inverted: True
⚡3D Cases Used⚡
www.thingivers...
www.thingivers...
Huge shout out to Bruh Automation for starting me on this ESP8266 journey on the first version of this multisensor a year ago. Please note, the product links above could be affiliate links, using them could earn digiblurDIY a small commission of purchases potentially helping with future video projects. Thank you! As an Amazon Associate I earn from qualifying purchases. Please note, the product links above could be affiliate links, using them could earn digiblurDIY a small commission of most purchases and helps with future video projects. Thank you! As an Amazon Associate I earn from qualifying purchases.
Негізгі бет DIY ESPHome Multisensor - Temp, Humidity, RGB LED, Motion and LUX
Пікірлер: 376