Might have been better when aligning the 3 disks to use DTI on tack weld then position them before final weld! I do love these videos watching how someone gets over a problem with ingenuity.
@user-ro7ek3oh9h
5 ай бұрын
Супер , молодец!! Я изготовил дробилку такого же плана,-молотковую дробит зерновые,сено,початки кукурузы,на вал установил вентилятор и дробленная масса уходит в мешок через цыклон. Заходите в гости имею дробилки разных конструкций, экструдеры,веялка зерновых,пресс для брикетов, чертежи..и другие поделки..
@tedbastwock3810
Жыл бұрын
I too wish to build a pellet machine and small hammer mill .. but I dont have a lathe and am not confident enough in my fabrication skill to build a machine that slings blades at 1700 rpm 😆 maybe one day. I do enjoy watching yours, though. Thanks so much for sharing!
@DorelBorlea
Жыл бұрын
A lathe is very useful for a household. I have never built a grinding mill either. I wanted to try and I see that I succeeded. Thank you for your support.
@venkatamohankandregula1557
10 ай бұрын
Sir could u please suggest this type hammer mill grind the waste printed circuit boards in to powder
@Armanufacturingskills
Жыл бұрын
Nice video
@pangskwelaranioy2903
6 ай бұрын
Nc project, can i ask what is the size of those nuts? and also the thickness of the plates?
@DorelBorlea
6 ай бұрын
Thanks. The plates are 6mm thick, the nuts are 16mm but I drilled them with a 19mm drill.
@Coazmaj
11 ай бұрын
I have one almost same, but with square blades. I switch side of blades because side that hits become rounded. So, side that hits is square again but I can see that parts of wood that comes out are a bit bigger than before. At start it was like in your video at 1st seconds of video. What can be a reason for that?
@DorelBorlea
11 ай бұрын
The type of wood and the humidity of the sawdust. The mill should grind the same, only the sawdust is different.
@theodorranebo2909
8 ай бұрын
Is it possible to make a hammer mill from an old dust blower fan? Must the "hammers" be movable or can i weld them directly to the fan blades?
@DorelBorlea
8 ай бұрын
I think you can build a straw grinding mill out of a dust fan. The hammer mill is built with movable knives.
@theodorranebo2909
8 ай бұрын
@@DorelBorlea I want to grind wood chips into smaller particles like sawdust so i can use it in my pellet press
@DorelBorlea
8 ай бұрын
I ground wood chips with this hammer mill. It's going super well.
@theodorranebo2909
8 ай бұрын
@@DorelBorlea Can you grind wood chips with a mill with fixed knifes?
@DorelBorlea
8 ай бұрын
@@theodorranebo2909 I don't know.
@janbolek8582
Жыл бұрын
Good work? But Mill for which material ?
@DorelBorlea
Жыл бұрын
straw, grass, alfalfa
@Armanufacturingskills
Жыл бұрын
Good work
@DorelBorlea
Жыл бұрын
Thanks!
@audreyungson207
6 ай бұрын
Hello sir, can it cut coconut husk?
@DorelBorlea
6 ай бұрын
Hello. I don't know.
@BERZOprojects2022
Жыл бұрын
Mai montezi inca doua axuri cu cutite s-au ramane in doua?
@DorelBorlea
Жыл бұрын
4 axuri cu cutite am vrut sa montez dar merge bine si cu doua.
@agusnahdliyanto1319
9 ай бұрын
Berapa harga satu unit pak
@igotbricotools2035
Жыл бұрын
Bun vídeo 👍 0:37 cand tai cu plasma la ce distantza tzii diuza de placa?
@DorelBorlea
Жыл бұрын
O tin lipita de material
@igotbricotools2035
Жыл бұрын
@@DorelBorlea merci , asha fac shi eu dar se mananca diuzele prea repede. Am cumparat un pistol cu masa incorporarata dar nu am apucat sal probez. Salutari din Spania
@DorelBorlea
Жыл бұрын
@@igotbricotools2035 la materiale pana in 6mm grosime duzele merg foarte bine. Am taiat aproximativ 3 metri de tabla.de 6 mm cu o singura duza si inaca mai merge.
@khadimdia9628
5 ай бұрын
Ok bien
@evanoliver44
3 ай бұрын
I wonder why you not cut the hair around the Dog eyes?
@denjaspersilorio7621
6 ай бұрын
what size are those blades sir?
@DorelBorlea
6 ай бұрын
96mm × 40mm x 3mm
@denjaspersilorio7621
6 ай бұрын
thank you very much! how about the plates and steel rods?@@DorelBorlea
@DorelBorlea
6 ай бұрын
@@denjaspersilorio7621 plates are 230mm , steel roads are 19 mm.
Пікірлер: 41