@@vijwalneelannaver5405 check the description of the vid
@guillewagner_l9836
Ай бұрын
Another question, on the batteries, i have to put 2 on the car and 1 on the sensor. What i do with the other slot of battery?
@ElectronicsisLife
Ай бұрын
Because when the motors are turned on they draws heavy current surges at start, causing voltage to dip which cause Arduino reset. For smooth operation connect separate battery for Arduino.
@guillewagner_l9836
Ай бұрын
@@ElectronicsisLife I asked the wrong thing: In the car, there are three battery slots, two needed for Volts and one for GND, no? So i should put three batteries there? Or another thing?
@guillewagner_l9836
Ай бұрын
Like i should buy 4 batteries? Thank you for the attention tho
@adekoyamufewa5556
4 ай бұрын
Good Evening sir Really love your work, wonderful work sir Sir please how do i connect the wire ti pcb board and which wires, I am still in high school and dont know really much on electrical engineering Gid bless sir❤
@adekoyamufewa5556
4 ай бұрын
And sir please which app do I use to code it and how will it function, do I plug something in my computer (So sorry for the disturbance sir, God bless you ❤)
@adekoyamufewa5556
4 ай бұрын
Sir please can you also explain what you did in 3:14
@ElectronicsisLife
3 ай бұрын
I am glad it worked for you, All the credit goes to you. PCBs made by you are awesome.
@guillewagner_l9836
Ай бұрын
Hello sir, hope you doing good. I'm a student and I'm willing to do this project. I have a question about the batteries, there is a difference between the black ones and blue ones?
@ElectronicsisLife
Ай бұрын
No, Both are li-ion batteries 18650 with slight difference in mAh capacity.
@tsish4792
14 күн бұрын
hello sir, just wanted to quickly ask, in the UK, AA batteries are far more accessible. Would it be possible to switch the 18650s to AAs?
@ElectronicsisLife
8 күн бұрын
AA batteries won't provide required current surges. You can give a try with alkaline AA batteries.
@HoracioGamerz
7 ай бұрын
Hello sir i have connected everything correctly but my receiver is not working the arduino and motor driver is lighting up but no response through transmitter the transmitter led for tx on arduino nano is on but on the receiver uno its not on please guide me what to do
@ElectronicsisLife
7 ай бұрын
On the receiver side Is Gnd of arduino and motor driver connected ?
@ElectronicsisLife
7 ай бұрын
If further not working, do email me images of your project.
@HoracioGamerz
7 ай бұрын
yes it is connected@@ElectronicsisLife
@ayshikpalit395
2 жыл бұрын
I haven't used button & led in transmitter...will it work with direct voltage supply??
@ElectronicsisLife
2 жыл бұрын
It won't, You need to change the code. Because by default transmission is disabled.
@ghost900
2 жыл бұрын
Hi Sir, where did you connect the ENA and ENB pins ?
@FemiOjeyemi
3 жыл бұрын
Hi, I connected everything correctly but can't get the tyres to move. I've tested all my parts individually and they all work, I even tested the transmitter and receiver side individually in Serial Monitor and got readings. For the transmitter, I am getting coordinates when I tilt the mpu6050, and for the receiver, I am only getting "START" showing in Serial Monitor. But when I connect both of them to test together, nothing happens and the tyres don't move at all, please help.
@ElectronicsisLife
3 жыл бұрын
Make sure the gnd (ground) of arduino nano, LM298 are connected with each other.
@FemiOjeyemi
3 жыл бұрын
@@ElectronicsisLife Thanks for your reply! My Arduino Nano is connected to my Mpu6050 which is on the receiver side, so I guess you are talking about the Arduino Uno on the receiver side, which I have already done, and it is still not working. :(
@ElectronicsisLife
3 жыл бұрын
Check battery voltages, Check the output voltage at the pins of Arduino nano at receiver end which are connected with LM298 driver.
@FemiOjeyemi
3 жыл бұрын
@@ElectronicsisLife oh ok, i did that, I noticed you used a switch for the transmitter and it's in the code. Is a switch needed for the code to work properly? Because I don't have one and I am just plugging the battery directly to the transmitter circuit.
@ElectronicsisLife
3 жыл бұрын
That switch is needed, By using that switch you can enable or disable transmission. Its handy in this case.
@minestrike9020
2 жыл бұрын
I have done all the connections properly for the transmitter and receiver. The serial monitor is showing output for transmitter , when i connect the receiver it shows "START" and the (0,0) continously. The data is not getting recived by the Receiver. Please help me out with this as soon as possible!!
@ElectronicsisLife
2 жыл бұрын
Do you have connected the button to transmitter ? Without pressing it, it won't start transmitting.
@minestrike9020
2 жыл бұрын
Yes the circuit and the connections are exactly same as you have showed in the video.....I have used the button, led and resistor as in the video but still the motors are not running..... What do i do?
@vinayakjadhav1719
2 жыл бұрын
@@minestrike9020 after pressing the button, is transmitter led turning ON , Make sure that gnd of LM298 and arduino are connected.
@minestrike9020
2 жыл бұрын
There is no data being received by the receiver
@ElectronicsisLife
2 жыл бұрын
Make sure that nrf24 pair working well, you can check this by uploading other library code. Make sure that all wires are connected where they needs to be.
@MrUnknown-hp1rk
5 ай бұрын
Hi sir, the project seems good and working but i have a doubt, how do you power the Arduino Uno? The connections seems fine, but i don't get it, a 18650 positive and negative would power the Arduino? In the schematic 3,3V and 5V are connected but how? I connect the 18650 at 3,3v but the 5V? The Arduino is the only thing that doesn't turn on because of power, i don't get it.
@ElectronicsisLife
5 ай бұрын
In the schematic 18650 is connected with 5v and there is onboard regulator which gives 3.3v.
@MrUnknown-hp1rk
5 ай бұрын
@@ElectronicsisLife Haha yeah man! It was my bad, I confused the 3.3v pin with the 5v because of the different design of my Arduino board. Anyways thank you! The project works fine at moment.
@diyasahachoudhury1242
3 ай бұрын
Sir which light will blink in audrino UNO? Tx or Rx ? I think it should be Rx but Tx light is on in mine. I have uploaded the code that you gave in the link. Please guide me🥹
@ElectronicsisLife
3 ай бұрын
Tx led should blink.
@KEVINESS0314
7 ай бұрын
sir,why do my arduino nano show red light but your show green light?
@ElectronicsisLife
7 ай бұрын
Because you manufacturer used red led, whereas mine used green.
@diyasahachoudhury1242
3 ай бұрын
All the lights of the audrino uno and the transmitter circuit is turning on, but the car is not moving. Please guide me sir! I dont know what i did wrong
@ElectronicsisLife
3 ай бұрын
Send some images/close-ups to my email.
@santos__zn
Ай бұрын
Did you manage to solve the problem? I have the same problem and I need to solve it in weeks, if you managed to solve it, what was the error?
@santos__zn
Ай бұрын
Did you manage to solve the problem? I have the same problem and I need to solve it in weeks, if you managed to solve it, what was the error?
@fouzanjaved5441
3 жыл бұрын
sir, can you please upload the hand gesture-controlled robotic arm by making the gesture-controlled robotic arm project and also give me the circuit diagram and the code to the gesture-controlled robotic arm project? thank you, sir.
@diyasahachoudhury1242
3 ай бұрын
Sir, Start is coming as an output in reciever serial monitor but then index number:255 is showing continuously. So the car is not moving Please guide me , i have done everything properly
@ElectronicsisLife
3 ай бұрын
Hi, Email me the images of what you have done.
@mamtakeer5162
Жыл бұрын
Hi ,my transmitter switch is not working.I have connected the wires according to the schematics the led is staying always on.
@ElectronicsisLife
Жыл бұрын
Have you connected switch to a correct pin ?
@mamtakeer5162
Жыл бұрын
@@ElectronicsisLife Thank you, I didn't connect wires of switch properly that's why It was not working. Also, I Need to ask you that do I need to download the libraries in Arduino uno as well. If yes than which one.
@ElectronicsisLife
Жыл бұрын
If your code is compiling without any errors, then no need. I have shown those libraries in the video itself.
@VinukaRanuljith
2 сағат бұрын
Hello sir can you tell me the code you used to car👍👍
@Aayush-q1w
5 ай бұрын
Can you pls tell if it is necessary to use a tactical switch .can,t we use a linear switch . I tried with a linear one but the bulb in transmitter was not glowing pls help
@ElectronicsisLife
5 ай бұрын
You can use any switch which can open and short.
@bharubhargavi9607
Жыл бұрын
Sir can you please upload a clear image of wiring part of transmitter and receiver connections was not understanding please help us sir
@ElectronicsisLife
Жыл бұрын
Plz goto to advanced settings and select 1080p, on my side it is very clear.
@prajwalashtekar3203
6 ай бұрын
Sir, the file of 2 code is does not open. It says this file format or Damaged. Please send the code again!
@ElectronicsisLife
6 ай бұрын
Its a .zip file, you need to install winzip or winrar.
@prajwalashtekar3203
6 ай бұрын
Sir in my pc winrar is already installed. Sir please help me. This is my science project
@ElectronicsisLife
6 ай бұрын
What message you are getting ?
@prajwalashtekar3203
6 ай бұрын
Sir have the code this project. Please sir!!
@ElectronicsisLife
6 ай бұрын
Share your email id.
@AarushSalwan
3 ай бұрын
i have a small question sir. can the same schematic used for the PCB work with the arduino shell? or is there some other special connection we need to keep?
@ElectronicsisLife
3 ай бұрын
Yes You need to connect pins shown in the schematic.
@AarushSalwan
3 ай бұрын
@@ElectronicsisLife Thank you so much. This video was very interesting and helpful
@AarushSalwan
3 ай бұрын
@@ElectronicsisLife if you know where i can find the arduino shell that would be helpful. if there is an amazon link, etc
@ElectronicsisLife
3 ай бұрын
Search for Arduino uno shield on Amazon.
@tonightsstorytelling1034
Жыл бұрын
Excuse me sir, I want to ask you, did you program the nrf24l01 as well? You put two programming codes, tx and rx, where did you use them? On what pieces?Please answer, I bought all the pieces and lost an amount on them, and now they do not work because of the code
@ElectronicsisLife
Жыл бұрын
No need to program nrf24. Tx code goes into the arduino nano on hand side. And rx code goes to the car side. If connection is right it shall work. Trust me its not that difficult, but if you are a beginner then pay extra attention towards connection. Be careful with batteries.
@tonightsstorytelling1034
Жыл бұрын
@@ElectronicsisLife I did everything you told me but it didn't move, all the parts turn on when i add the batteries but it don't move, can I get your number and send you a picture of the car and tell me if there is a mistake, please I really feel embarrassed in front of the school administration because they chose me and paid them The amount, but now I don't know why its not work, and I have to hand it over to them within two days know
@ElectronicsisLife
Жыл бұрын
Kindly send me some images to my email. Without that it impossible to help you. Don't panic. My email id is electronicsislife.english@gmail.com
@tonightsstorytelling1034
Жыл бұрын
@@ElectronicsisLife Hello, sir, how are you?I sent you some pictures on the e-mail. Can you please reply to me? I have been waiting for your reply since yesterday,Thank you
@yourbrolucky7201
2 жыл бұрын
Sir, please I don't understand that wiring of the Arduino sheild that you have made sir please reply
@astromaze
19 күн бұрын
Which website did you use to put together the electrical diagrams?
@ElectronicsisLife
17 күн бұрын
Easyeda.com
@mastafa911
2 жыл бұрын
Hello, my friend, how are you . I did the same way to make the car and connect the wires. But it does not work, what is the reason? Can I contact you about this matter ?
@ElectronicsisLife
2 жыл бұрын
Is you connected Gnd of L298 motor driver and Arduino connected to each other ?
@mastafa911
2 жыл бұрын
Think you my friend . It is working . My mistake was in (L298N) i remove the content in (motor 1 Act/Des) and (motor 2 Act/Des)
@tonightsstorytelling1034
Жыл бұрын
@@mastafa911 how do you do that because i have a problem, my car don't work
@mastafa911
Жыл бұрын
@@tonightsstorytelling1034 what the problem in transform or reserve circuit
@crseven-qg6fp
8 ай бұрын
@@ElectronicsisLife7:00
@yourbrolucky7201
2 жыл бұрын
Sir, please can you upload the pic of wiring of both the transmitter and receiver
@ElectronicsisLife
2 жыл бұрын
Please don't panic, I shall help you.
@abdelrahmanmohamed7893
4 ай бұрын
Good evening sir , I’ve connected everything the right way and I’ve uploaded the code and everything is on , but it won’t work , could you help please , my deadline is in 5 days and I don’t know what is not working
@ElectronicsisLife
4 ай бұрын
Reply to your email
@santos__zn
6 ай бұрын
Please send me the link to buy the parts, a kit that comes with everything, buying the parts separately is very expensive
@battlefieldgaming3052
Жыл бұрын
Bro in Arduino Uno there are 2 gnd should we connect both together or 1 gnd connect with battery + and second with nrf24
@ElectronicsisLife
Жыл бұрын
Both are same gnd, no need to connect both. Even if you connetted both won't cause any problems. But same gnd should be connected with all other parts.
@battlefieldgaming3052
Жыл бұрын
@@ElectronicsisLife thanks broo for reply but i have a problem when i connected all wire in transmitter Arduino nano and try to start it the battery holder wire are start burning and battery holder know not working but Arduino nano and mpu6050 are safe
@ElectronicsisLife
Жыл бұрын
Most probably You have connected batteries in opposite polarity.
@TimeaLukacs-e2f
Жыл бұрын
hello, what type of battery are u used (voltage and mAh) (that link is unavailable)? Those battery holders are connected in series or parallel? Thk
@ElectronicsisLife
Жыл бұрын
18650 Lithium ion batteries Capacity is around 2600 mAh.
@manuh2652
Жыл бұрын
Hi Sir, I made the project but seem to have a problem I am not sure what the problem, but in the transmitter device when the switch is turn on but LED is not on. If you have any suggestions, or if you think there could be any other problem please reply, Thank you.
@ElectronicsisLife
Жыл бұрын
Don't worry, Lets try to solve it. Do reply me on the email with requested images.
@santos__zn
2 ай бұрын
Sir, my LED doesn't light up, it only lit up once when I entered the code, but when I pressed the button it went out and didn't light up again, now it doesn't light up even when I enter the code, everything is ok with the soldering of the connection wires, I don't know what's wrong, can you help me?
@ElectronicsisLife
2 ай бұрын
Did you connect resistance in series with led ?
@santos__zn
2 ай бұрын
@@ElectronicsisLife yes, I connected, I followed all the steps in the video, exactly as it is in the video
@J_sin
3 ай бұрын
Sir how much ohm of resister did you use ? For led
@ElectronicsisLife
3 ай бұрын
510 ohms to 4700 ohms
@santos__zn
Ай бұрын
Sir, I did everything as shown in the video, all the lights come on but the LED doesn't go out when I press the button, it just reduces the intensity, and the cart doesn't move, please help me, I need to deliver this ready in weeks
@ElectronicsisLife
Ай бұрын
Please email me some pictures of your project. Which batteries you are using ? Make sure battery voltage is healthy.
@santos__zn
Ай бұрын
@@ElectronicsisLife Yes sir, give me your email so I can send you the photos
@abdulfattahofficial02
Жыл бұрын
Can you please give me a good assembly its hard to understand please
@snuuky8814
4 ай бұрын
Good day sir how do I connect the ground pins if I'm using jumper wires thank you
@ElectronicsisLife
4 ай бұрын
Already replied on E-mail.
@harish.b3059
7 ай бұрын
Help me : I have made the circuit as per your circuit diagram, TX part is transmitting signals properly and I had checked that in the serial monitor while the receiver part first shown only start then I had connected separate battery for RX arduino (separate battery for l298d and arduino) then the serial monitor shows 0,0 Please help me in this regard
@ElectronicsisLife
7 ай бұрын
Its seems good. (As expected) Did you connect gnd of arduino with gnd of L298 motor driver ?
@harish.b3059
7 ай бұрын
No I have connected separate batteries for arduino and l298 motor driver, not connected gnd of arduino and l298 motor driver
@ElectronicsisLife
7 ай бұрын
Do connect both gnd point, so that arduino and l298 driver will be at same voltage/reference level. Without it , L298 won't work.
@sulthanrakaathallahherla-mm2eg
Жыл бұрын
Mr, I wanna ask, why my transmitter switch button didn’t connect ? Please answer me
@ElectronicsisLife
Жыл бұрын
Without any look or images its impossible to say anything. Share some images, email in about section.
@user-gi8kn1vk2p
2 жыл бұрын
Excuse me sir, i use 6v battery to arduino uno and 9v to L298N, but motor didn't work and only L298N has some buzz.....
@ElectronicsisLife
2 жыл бұрын
On which pin of arduino you connected 6v battery ?
@gamingemerald6069
10 ай бұрын
Should we put a code to the transmitter
@kshirjarajput6207
4 ай бұрын
Sir can you please help me I don't know what I am doing wrong but the led never seems to turn on. Please help.
@ElectronicsisLife
4 ай бұрын
Kindly email me the images of your project.
@jigneshmore2756
2 жыл бұрын
How to connect nrf module to Arduino shield
@ElectronicsisLife
2 жыл бұрын
Shield provides lot of general purpose pcb , using solder you need to make connections for nrf module.
@tonightsstorytelling1034
Жыл бұрын
Hello, I want to ask you about the resistance in the Arduino Nano board. You connected one of the two sides to the LED، But the other side, where did you connect it?Please reply that I am doing it as a project for the school and I am supposed to deliver it to them tomorrow.
@ElectronicsisLife
Жыл бұрын
You can use any valie from 470 ohms to 1000 ohms.
@ElectronicsisLife
Жыл бұрын
Other side connected to the pin of arduino itself.
@zeyadsaid5075
Жыл бұрын
Hey in the transmitter schematics there are two vcc on in the arduino nano and one in the mpu6050 and only one battery available. Do I connect the positive end of the battery to two connector wires and connect them? Or?
@ElectronicsisLife
Жыл бұрын
Yes Same battery positive terminal goes to arduino as well as MPU6050.
@zeyadsaid5075
Жыл бұрын
@ElectronicsisLife OK thank you so very much. Tomorrow I have to submit my STEAM car. Your video helped me a lot!
@zeyadsaid5075
Жыл бұрын
I also removed all the code related to the switch button. I hope I didn't mess up the code
@ElectronicsisLife
Жыл бұрын
I am glad it helped you.
@616lizzie
2 жыл бұрын
Please give me buy link of rediment Arduino shield
@NaveenSins
10 ай бұрын
Thanks it works
@adekoyamufewa5556
4 ай бұрын
Hey please can you guide me?
@diyasahachoudhury1242
3 ай бұрын
Hi. Can you please tell which light is on in audrino uno. Tx or Rx
@diyasahachoudhury1242
3 ай бұрын
@NaveenSins
@NaveenSins
3 ай бұрын
@@diyasahachoudhury1242 hi
@tonightsstorytelling1034
Жыл бұрын
4:34 Here you connected the other end of the resistor with the sixth port?
@ElectronicsisLife
Жыл бұрын
4:02 In the wiring diagram, tx indicator is connected with D3.
@abdulfattahofficial02
Жыл бұрын
Where does the other end of the indicator goes? Where is D3? Just tell me which port of the nano indicator goes. Thks
@Vin-o5r
7 ай бұрын
sir, do i need to change the code and wiring if i am only going to use 2 dc motors?
@ElectronicsisLife
7 ай бұрын
No, but make sure you are using 3rd spherical wheel.
@unknownperson4316
2 жыл бұрын
Do I need upload the rf24 on the transmitter module as well.
@ElectronicsisLife
2 жыл бұрын
Yes
@gamingemerald6069
10 ай бұрын
Can you give a straight link for the code
@janhvikhedekar9305
3 жыл бұрын
Mind-blowing
@wanasooriyamudiyanselageda2621
Күн бұрын
can you tell the code that you apply to this car ? please i want it quickly
@ElectronicsisLife
22 сағат бұрын
Link to the code is in the description below.
@Panda9_
21 күн бұрын
good afternoon sir, if i use same battery for arduino uno and rf module, will it be okay?
@ElectronicsisLife
17 күн бұрын
Yes
@Panda9_
17 күн бұрын
Thank you so much sir for clearing my doubt! However can you tell me how and where to upload codes?
@user-gq1vp4wq8m
5 ай бұрын
Sir i given the connection correctly but i still not working may be I'm mistaken in GND connection both receiver and transmitted because in circuit diagram the GND are look like a same .I don't have an idea ...pls give me clear connection of gnd both circuits .....i want submit my project nxt week ... I'm requesting u to guide me
@ElectronicsisLife
5 ай бұрын
Email me photos of your project.
@user-gq1vp4wq8m
5 ай бұрын
I'm send email sir pls check it sir@@ElectronicsisLife
@vijwalneelannaver5405
13 күн бұрын
Dear sir, I am very much confused about the code & can you please provide the link of the code for me?
@ElectronicsisLife
8 күн бұрын
You can email me your doubts.
@abhijeetdaberao8078
Жыл бұрын
Can we use an motor driver shield on Arduino Uno for Receiver?
@ElectronicsisLife
Жыл бұрын
Yes
@sameerr9141
2 жыл бұрын
Can you please provide me another receiver circuit diagram because from this my rf module not working. Dont know about this problem. Please provide me a schematic diagram.
@sameerr9141
2 жыл бұрын
@Electronicsislife
@sameerr9141
2 жыл бұрын
This is my final yr project .please help me . If it is working then i will pay you some money. I dont have time. Please help me sir
@ElectronicsisLife
2 жыл бұрын
Money not needed. Plz share images to my email.
@sameerr9141
2 жыл бұрын
Please provide me your mail address
@ganeshreddy7258
2 жыл бұрын
U have not mentioned any acceleration meter in the description but u have used in the video
@ElectronicsisLife
2 жыл бұрын
Yes, while assembling the car I Have accelerated But while in work Its real time, I Shall Do it in future videos.
@Cookingwithlaxmi3
2 жыл бұрын
Bro can I use a l293d moter drive In place of the of the receiver part you made
@ElectronicsisLife
2 жыл бұрын
Yes u can, provided current is less than 1 amp. L298 current rating is upto 4 amps.
@malikasfandyarzakir6847
Жыл бұрын
dude can u tell me if i need hole to hole or Pin to pin or HOle to pin wires ? bcz im making a project and i need to know it and its not opening in website
@ElectronicsisLife
11 ай бұрын
Mostly Hole to hole.
@artificialladka9838
Жыл бұрын
Hi sir can you please tell me the size of the pcb because the link you have given is not working
@ElectronicsisLife
Жыл бұрын
2 inch x 3 inch
@Bravo141-6
4 ай бұрын
Does it work with only two lithium batteries or should i use 3 ?
@ElectronicsisLife
4 ай бұрын
3 1 for arduino and sensors 2 for motors
@Bravo141-6
4 ай бұрын
@@ElectronicsisLife 3.7 v 2600mah enough?
@ElectronicsisLife
4 ай бұрын
Yes
@faltukidz
2 жыл бұрын
Dose this car really work, like are the codes and circuit diagram all working.
@ElectronicsisLife
2 жыл бұрын
Absolutely!
@isandunethmira6694
5 ай бұрын
Is there any other option without the MPU6050 module... we found it but an error occurred.... Plz help me...
@ElectronicsisLife
5 ай бұрын
Try to resolve that error. What error you are getting ?
@isandunethmira6694
5 ай бұрын
@@ElectronicsisLife It's ok.. i done it..
@mamtakeer5162
Жыл бұрын
Hi, I have connected everything correctly even then my motor is not moving. Can you help me?
@ElectronicsisLife
Жыл бұрын
Send me some images to my email. electronicsislife.english@gmail.com
@techsector5698
9 ай бұрын
Brother i am not having led , button and resistors for rf please help me with the code tomorrow morning is my competition and i am not getting green light on nano
@ElectronicsisLife
9 ай бұрын
Email me the pictures, I can guide you there. You must use switch and LED, its for enabling the transmission and indication purpose.
@aboudafitna8045
Жыл бұрын
It works 😍😍❤️❤️
@SPIDEYGAMINGZONE-gg2nb
10 ай бұрын
Brooo
@SPIDEYGAMINGZONE-gg2nb
10 ай бұрын
I have some doubt can you clear me
@kaushaltrivedi8877
2 жыл бұрын
Hello i have l293d motor driver How to connect nrf24l01 with l293d Its possible ?
@ElectronicsisLife
2 жыл бұрын
No. You need microcontroller like arduino t9 control them.
@crazybarney2554
2 жыл бұрын
Do you have a link to the resistor you used in the video???
@ElectronicsisLife
2 жыл бұрын
Its a normal through hole resistance , You can use any value from 510 ohms to 10k ohms.
@crazybarney2554
2 жыл бұрын
THANK YOU SO MUCH!!!!!!!
@kutlurobotics5487
2 жыл бұрын
@@ElectronicsisLife my nrf24l01 module can't work what can i do
@crazybarney2554
2 жыл бұрын
@@ElectronicsisLife do you have another link for the code because the link that is in instructables Is not working? (My apologies for the many questions and thank you for answering!)
@LofiBoy2873
Жыл бұрын
Sir can you please give me the code.When i open the code is not showing anything in my device
@ElectronicsisLife
Жыл бұрын
Its a zip folder. Plz mail me I'll share the code. email id is electronicsislife.english@gmail.com
@arturosierra6979
10 ай бұрын
hola, una consulta los capacitores que utilizas que caracteristicas tienen ?
@ElectronicsisLife
10 ай бұрын
Answering in english, Capacitor provided high current in the form of spikes, keeping volgage stable.
@ElectronicsisLife
10 ай бұрын
Capacitors I have used are of 100uf/25v, they are electrolytic capacitors.
@crazybarney2554
2 жыл бұрын
What is the name of the switch you used in the video???? ( btw great video, this has been very helpful!!!!)
@ElectronicsisLife
2 жыл бұрын
Its a tactical switch.
@crazybarney2554
2 жыл бұрын
Thank you!
@asmaelhseb1113
2 жыл бұрын
Hello, I applied everything in detail and there is a transmission on the serial monitor screen, but the motors do not move. Can you advise me, thank you
@ElectronicsisLife
2 жыл бұрын
Is gnd of l298 and arduino connected ?
@asmaelhseb1113
2 жыл бұрын
@@ElectronicsisLife yes
@asmaelhseb1113
2 жыл бұрын
@@ElectronicsisLife What should I lose?
@ElectronicsisLife
2 жыл бұрын
@@asmaelhseb1113 plz mail me the pictures, and ill try to figure it out. Its difficult to tell over here.
@bharubhargavi9607
Жыл бұрын
Hi sir TX and RX code was not open sir please help us, can you please send us another any other link for transmitter and receiver coding.
@ElectronicsisLife
Жыл бұрын
Its a rar file, you need to install winrar to extract it.
@antonysebastian7860
4 ай бұрын
Sir can you please help my accelerometer gets on then suddenly the gets off
@ElectronicsisLife
4 ай бұрын
Led on accelerometer get ON and off ?
@rishitsahu4660
Жыл бұрын
bro just a suggestion. Whenever u make the circuit diagram please make it easy like the ones made in fritzing. Its too easy. bcs the circuit u made is difficult to understand
@ElectronicsisLife
Жыл бұрын
Noted.
@mohamedshady910
Жыл бұрын
Hey Sir, I made the project but seem to have a problem I am not sure what the problem could be, but I think it might be the nrf24 module. If you have any suggestions, or if you think there could be any other problem please reply, Thank you.
@ElectronicsisLife
Жыл бұрын
Please share me some images of the soldering and wiring of your project. electronicsislife.english@gmail.com
@mohamedshady910
Жыл бұрын
@@ElectronicsisLife Okay, Thank you.
@crazybarney2554
2 жыл бұрын
Hi, do you have another link for the code because the link that is in instructables Is not working?
@ElectronicsisLife
2 жыл бұрын
Ok, give me sometime.
@crazybarney2554
2 жыл бұрын
@@ElectronicsisLife ok no problem
@ElectronicsisLife
2 жыл бұрын
I just downloaded (All) files from instructables. Seems good. What problem you're facing ? Are you unable to download it or the code is not working on your side ?
@crazybarney2554
2 жыл бұрын
@@ElectronicsisLife yeah I’m not able to open the code. When ever I do try to open the code file, it says I don’t have the application set to open the document. Also thank you for answering!
@crazybarney2554
2 жыл бұрын
@@ElectronicsisLife is there a specific application you have installed besides arduino application??
@jigneshmore2756
2 жыл бұрын
what is the value of resistor used in arduino nano pcb
@ElectronicsisLife
2 жыл бұрын
Its a 1K ohms resistor.
@Kuldeep.Singh15
Жыл бұрын
Do you also sell these ready made projects?? We want to buy !!
@ElectronicsisLife
Жыл бұрын
Not yet, you can build it by urself, I shall help you for free.
@omarmohessa
3 ай бұрын
I connected everything just like u I even connected the motor driver 5v and ground to Arduino It starts but won't go
@ElectronicsisLife
3 ай бұрын
Hi Email me some closeup images of what you have done,maybe i can figure out something.
@omarmohessa
2 ай бұрын
@@ElectronicsisLife what is ur email ?
@abhinavmaurya9042
2 жыл бұрын
I had follow your video tutorial and assemble all the part.I don't know why it is not working. Please help me. Reply me ASAP, I had to submit this as my project.( My transmitter is working and I had make all the connections correct in receiver) Please respond😢😢
@ElectronicsisLife
2 жыл бұрын
Sorry for the late reply. You can mail me the details or pictures.
@AnitaSharma-xe4do
2 жыл бұрын
@@ElectronicsisLife i am also getting same problem......but why all peoples getting same problem..
@AnitaSharma-xe4do
2 жыл бұрын
@@ElectronicsisLife bhai mene orr sab ki bhi videos dekhi pr zadatar sab ko ye hi problem aa rhi h....me ye 1 saal se shi krne ki koshish kr rha hu pr shi nhi huui
@timealukacs2591
Жыл бұрын
Capacitor is mandatory to use?
@ElectronicsisLife
Жыл бұрын
Yes
@padminikamalahasan5012
10 ай бұрын
Sir is it ok if i dont have the capacitor attached to the 24l01 module????
@ElectronicsisLife
10 ай бұрын
The communication won't be smooth then, small capacitor is needed.
@padminikamalahasan5012
10 ай бұрын
@@ElectronicsisLife i completed my project without a capacitor. is it ok sir?
@ElectronicsisLife
10 ай бұрын
Nice, It would work but some time the communication may not be smooth.
@ahmedalaraj4492
3 жыл бұрын
what is the name of software using to draw circuit
@ElectronicsisLife
3 жыл бұрын
Its a website easyeda.com
@rishitsahu4660
Жыл бұрын
bro i made the car. when i tilt my hand rx unit it works nicely and my tx is even receiving the signals in serial monitor. but the motors are only making a sound but are not moving. pls help. my exhibition is after 3 days
@rishitsahu4660
Жыл бұрын
pls help asap
@ElectronicsisLife
Жыл бұрын
Make sure that you have connected motor driver gnd with arduino gnd.
@gamingemerald6069
10 ай бұрын
What happens if we don't put rf module
@ElectronicsisLife
10 ай бұрын
There won't be any communication between Transmitter and receiver, car won't operate.
@dorcassanum6455
Жыл бұрын
What is the page or the sistem that you used for the code ? and can you share the code please
@ElectronicsisLife
Жыл бұрын
Its called Arduino IDE, code is in the description.
@christianpiero4340
2 жыл бұрын
please am in Ghana where can I get these parts to make the car
@ElectronicsisLife
2 жыл бұрын
Any online/offline electronic store.
@parthasarathysil1300
2 жыл бұрын
hello. my serial monitor show some dummy text.. why?
@ElectronicsisLife
2 жыл бұрын
Check the baud rate, some text will be thrown on the serial uart.
@SubhranilPal-q1y
Жыл бұрын
my code is not uploading on the arduino uno...what should i do??
@ElectronicsisLife
Жыл бұрын
Check what command you getting while uploading the code.
@user-yf4su2kf6h
Жыл бұрын
hey can you send me soft copy of your code
@zeyadsaid5075
Жыл бұрын
Hello again. Is there an ability to replace the l298N motor driver with arduino motor shield?
@ElectronicsisLife
Жыл бұрын
Yes You can. Arduino shield has L293. Both work similarly. Only Make sure that inputs and outputs are properly connected.
@zeyadsaid5075
Жыл бұрын
@@ElectronicsisLife thanks
@Diymakervn
Жыл бұрын
My car doesn't turn left or right. It only accepts forward and backward. Can you show me where the error is?
@ElectronicsisLife
Жыл бұрын
Email me se pics and videos. electronicsislife.english@gmail.com
@snuuky8814
18 күн бұрын
Good morning. have you solved this?
@ravindranathareddy.j5544
Жыл бұрын
Hi sir,this is Ravindranatha Reddy from Tirupathi, Andhra Pradesh, can we transform a stunt type Remote controlled toy car into gesture controlled toy car ?how much total price of only electronic components(transmitter &reciever) of the toy shown in this video
@ElectronicsisLife
Жыл бұрын
Hardware cost was around 2000 ₹.
@emon2435
Жыл бұрын
why you use button? If i don't press in button transmitter will not be allowed
@ElectronicsisLife
Жыл бұрын
Yes, button provides us flexibility of operation.
@atharvakhobragade2277
Жыл бұрын
Sir how to join wires please tell me I can't understand please it's humble request
@ElectronicsisLife
Жыл бұрын
By using soldering iron and solder.
@gamingemerald6069
10 ай бұрын
Can we make without putting the switch
@ElectronicsisLife
10 ай бұрын
No, switch is used to enable or disable transmission.
@harishshairesh4806
5 ай бұрын
I have given all the connection and all the grounds correctly but still the car is not moving how to contact you
@diyasahachoudhury1242
3 ай бұрын
Hey? Did you get it right? If yes, then please guide me. Because mine is also the same problem
Пікірлер: 553