This needs to have a different term than “heat treat oven.” It’s kind of like calling the Vatican Palace “some dude’s house.” I’ve been thinking about building one for a while, but making it look decorative never entered my mind. Amazing project & well built aside from the aesthetics!
@RastoFurlan
Жыл бұрын
In point 2 and in point 11 you have different heating wires, which one is the right one? Nice work!
@oihanhuanyyd9280
3 жыл бұрын
cool project!!! can’t wait to give it a try.
@TNCXBUNBOX
3 жыл бұрын
Thank you ! And all the best to your project !
@jorisArt
4 жыл бұрын
First of all, I’d like to say that’s a heck of an effort and it looks like a great kiln! I just have a couple of questions - why the pebbles and refractory cement on the bottom over the refractory brick? I wouldn’t think there was much heat leakage there, end it seems like a very strong layer that you could walk on but why? The second question is why the ceramic tiles on the outside. I am really curious - I have made a killing from scratch which I use for burnout purposes and run to 800°C and I am in the process of rebuilding a much larger pottery kiln which goes up to 2200°F/1150 Celsius. These are just built from refractory brick with a blanket of refractory insulation over them in a stainless steel sheet metal case. I am interested in your comments. I’d like to add I really like your workmanship-itall looks great!
@TNCXBUNBOX
4 жыл бұрын
Hi Joris, thank you for watching my video and I really appreciate how you pay attention to those details
@misterbleach6581
Жыл бұрын
Did you use 44 lbs of cement or 22? Great video.
@MartynTverdun
2 жыл бұрын
great piece of work! What was the highest temperature you were able to get on that kiln. Thanks!
@seanscimeca1
3 жыл бұрын
Great video. Amazing construction. Question - do you have a wiring diagram for how you ran this with the 220v? I am currently using 110v in a build similar to this but would like to upgrade to 220v.
@howtomake1446
3 жыл бұрын
Sir nice work. But i want a oven like this and want to run it 10 to 12 hours continue. Will this oven work 10 to 12 hours continue
@TNCXBUNBOX
3 жыл бұрын
Thank you! Yes it will work for 12 hours. Just don't embed the coil in cement like i did. Instead, please use stainless steel hooks/screws to hold the coil.
@howtomake1446
3 жыл бұрын
Thanks sir very good idea
@feliciasugiarto_
2 жыл бұрын
Hello what if i want to make a bigger one, is there any different measurements?
@Lowbattery_fpv
2 жыл бұрын
This is great.! Well done. Have you a pdf file of this project? Thanks
@szopanawsi
3 жыл бұрын
Great job 👍👍👍
@donwatts6588
Жыл бұрын
Hi there what is the max temperature needs for heating rod for this size kiln
@antoniomartins1112
3 жыл бұрын
A good job without a doubt. I have an equal controller (mc701). How do I increase the temperature slowly instead of going straight to 100%, say 60% or 35% etc ... Does it not have this function? I can't find out. Thanks
@TNCXBUNBOX
3 жыл бұрын
Thank you for your support ! To answer your question : In order to have this kind of PIDs, please looking for the "Soak and Ramp PID" - this we can set up to 32 steps or more of how we want the temperature in period of time. For this MC701 PID or similar simple model, all we can do is set the temperature raise slowly manually.
@howtomake1446
3 жыл бұрын
Sir one Question. What is the full length of kanthal wire used in this kiln ?
@TNCXBUNBOX
3 жыл бұрын
Hi. I don't remember exactly, I just Multiply ohm per foot (on the lable of the package 16GA 0.33 Ohm/foot), it's about 66.5 Feet or 20m length for 22 Ohm Resistance. Hope this help.
@howtomake1446
3 жыл бұрын
Thanks sir
@nathanmartin6002
3 жыл бұрын
SWEEEEETTT!!!
@rcistarliteinternational4502
3 жыл бұрын
can you please tell me where to purchase the red alarm bell
@donwatts6588
Жыл бұрын
Using it for a burn out kiln for lost wax casting
@dameonb4586
3 жыл бұрын
Question: I didn't see how you made the kiln door. Was it just moulded refactory cement?
@TNCXBUNBOX
3 жыл бұрын
Hi Dameon, I use relatively long screws to attach the hinges to the brick (as it quite soft) then embedded the hinges to both Body and door with the refractory cement. Until now it is perfectly strong, very strong. Hope this helps.
@dameonb4586
3 жыл бұрын
@@TNCXBUNBOX was the door made from fire brick or just cement?
@TNCXBUNBOX
3 жыл бұрын
It was made with FireBricks too. 👌
@jaihagusto272
3 жыл бұрын
How do you adjust your resistance? Also, is the wattage coming off of the pid?
@Ab0minati0n
2 жыл бұрын
Risistance is governed by the length of the element wire and dependant on it's diameter. For the heat treat kilns i build I my elements are 23 ohms to achieve 9.7A of currnet at 220vac to be able to run off a regular outlet
@calmmeoriginalofficialchan9110
3 жыл бұрын
What did all the components cost?
@sherryk4960
3 жыл бұрын
Ok how much and when can I get one :)
@TNCXBUNBOX
3 жыл бұрын
Thank you for being interested in my project. It's good for DIY and home use so far only. Hopefully in future I can make some commercialised products for supporters like you. Thank you
@knowledgeabundant
4 жыл бұрын
sorry, i don't see the link to calculate, i have 110 v and a 15 amp breaker. Thank You
@TNCXBUNBOX
4 жыл бұрын
Thank you for reminding me ! Here is the link for you: www.rapidtables.com/calc/electric/power-calculator.html (I also update the link in the Description)
@aryputra7819
4 жыл бұрын
is there air circulation? And if there is no air circulation, can it cause an explosion because the hot air inside the oven is trapped?
@TNCXBUNBOX
4 жыл бұрын
As you can see in the Video, the steam was coming out (when the oven was still moist) between the gap of the Door and the oven. It is not completely sealed like a Pressure pot or a vacuum chamber, steam can slowly come out when I do my pottery
@hermansujana8405
3 жыл бұрын
if you need 22 ohms and 0.515 coil resistance, it should be 42.72 meters of wire sorry i'm still confused
@hermansujana8405
3 жыл бұрын
L=R/r L=22ohm/0.515 L=42.7 meter correct please
@TNCXBUNBOX
3 жыл бұрын
The resistance of the 18 GA Kenthal wire as it is stated is 0.515 per Foot (not meter), therefore, it 's equivalent to 42.7 Feet = 13.02 Metres . Hope this help you !
@imstubby6844
3 жыл бұрын
Get rid of 'music'
@ctpctp
3 жыл бұрын
20 minutes straight of it. Dammmmmmn. Thank god for the mute button.
@TNCXBUNBOX
3 жыл бұрын
My bad 😢! Many Thanks for your advice!
@jorgebauterivero6771
3 жыл бұрын
Sz
@albertoinglesi1
2 жыл бұрын
hai anche avuto il coraggio di pubblicarla questa cazzata
Пікірлер: 46