I don’t understand the dislikes. This fellow has done an informative vid in 3.5 min instead of similar in twice the time and its free. There are some strange people out there. Thanks bloke.
@kawashah
Жыл бұрын
Haters got to hate.
@peterlejeune587
6 жыл бұрын
At last a DIY video that clearly explains a process without unnecessary mumbling and obfuscation and presents a clear video with the commentary. Very useful..
@4DIYers
6 жыл бұрын
Thank you, I really appreciate the feedback!
@carlosrobles2048
4 жыл бұрын
I was just about to say the same thing. thank God videos like this exists, it's too bad you have to filter through a hundred pieces of trash to get to the diamond in the rough
@cerrem1
4 жыл бұрын
Yea...reminds me of training classes in the USMC, but without the yelling ... straight to the point...Just the facts ma'am.....
@ronaldcarson4360
4 жыл бұрын
@@cerrem1 and no damn music... Semper Fi
@cerrem1
4 жыл бұрын
@@ronaldcarson4360 I remember a fellow Marine falling asleep in a training class... They smashed a wood chair over him to wake him up.... I found out he later had a cracked spine and was in Beaufort Naval Hospital....
@leokimvideo
2 жыл бұрын
One of the very few videos on this way of bleeding brakes thats to the point and accurate. Seen plenty of others that are just a total waste of time
@4DIYers
2 жыл бұрын
Thank you, I appreciate the feedback!
@timsherwood2804
3 ай бұрын
Straight to the point no excessive talking, music or explaining. I had my brakes bled and working within 10 minutes
@CORZER0
5 жыл бұрын
Concise and informative. Perfect! Not everyone needs a 20 minute video on how to properly inflate tires. Thanks!
@4DIYers
5 жыл бұрын
Thank you, I appreciate the feedback :)
@Jimidan1000
4 жыл бұрын
This is a lot more complicated than inflating a tire.
@paulellis1947
3 жыл бұрын
Dude seriously tho it's easy stuff let's keep it that way 😂
@PlatinumG
3 жыл бұрын
This has nothing to do with inflating tires.. but I agree, short and to the point video.
@taterlysaladman9377
5 жыл бұрын
If school teachers articulated like this, we would only need about 6 years of public education...
@4DIYers
5 жыл бұрын
Thank you so much for the kind words :)
@dreymcmillan1697
3 жыл бұрын
@@4DIYers morning
@kina0606
3 жыл бұрын
@@dreymcmillan1697 evening
@whoisharo4689
3 жыл бұрын
Is this a compliment or insult? I'm too stupid to figure it out.
@jhunswerr8669
3 жыл бұрын
@@whoisharo4689 compliment
@louthunited
5 жыл бұрын
Have to agree with all those commenting on how well presented this tutorial is. Perfect, tells you what you need to know in a clear, concise manner.
@4DIYers
5 жыл бұрын
Thank you so much for the kind words :)
@Blaze-wx8li
2 күн бұрын
Super helpful, thanks. Thanks to your video I realized I had been pulling air bubbles from around the threads for about an hour, wondering why there was so much air in system
@4DIYers
23 сағат бұрын
You’re welcome!
@michaelmclernon4929
6 жыл бұрын
Good Video. Air bubbles coming in around bleeder screw are usually vey fine, and constant, where the system air will be larger bubbles. I usually don't use any more vacuum than necessary to get fluid flow because excessive vacuum can pull air in around the hydraulic cylinder seals which is not good. It takes a bit of practise to tell the difference, but once the large bubbles are gone you should be OK, the tiny micro bubbles from the bleeder screw cannot get into the cylinder, so you have to learn to identify them and live with them.
@IbnuCuruk
Жыл бұрын
I was exactly searching for this information. Thanks a lot.
@tweston24
2 жыл бұрын
Simple. To the point. Should be the number one search option
@4DIYers
2 жыл бұрын
Thank you so much!
@raabsand
5 жыл бұрын
Thank you. Straight to the point no bullshit. No one cares who you are and what your story is on these types of videos. No offense just calling out other video makers
@4DIYers
5 жыл бұрын
Thank you :) No worries, I definitely don't want to mix in my personal life with auto repairs. I like keeping everything right to the point efficiently.
@amorag59
4 жыл бұрын
One of the most important things that is overlooked in most reviews and walkthroughs: be sure to put the rubber seal on the top of the cup to seal the cap to the cup or else it won't develop vacuum. I tried taping the holes on top of the cap, I almost returned the thing until it clicked that I had to use those little rubber band looking seals...
@tagu2434
4 жыл бұрын
I had the same frustration today!
@kalahwilson4549
8 ай бұрын
Most helpful comment of the day!! Thank You 🙏🏻
@BeADad2447
Ай бұрын
Excellent video. As an added precaution you can apply pressure to your brakes with an extra leg or any another way! Great video thank you!
@4DIYers
Ай бұрын
Thank you so much!
@stevensteel8617
3 жыл бұрын
Thanks for the tips, especially on the need to build up a negative pressure before opening the nipple. I have seen another video where the person was just using it as a pump to suck the fluid through. Your video seems to answer another of my questions which is whether you have to pump several times to build up the vacuum or whether you just have to hold the pump open. So there does seem to be a non return valve of some sort in the pump, like a bicycle pump but in reverse. Cool. Thanks for that.
@4DIYers
3 жыл бұрын
No problem, glad I could help. I also have an updated version too in much better quality if you haven't seen it kzitem.info/news/bejne/zHyHrq1okHV1dm0
@JSB2500
Жыл бұрын
01:58 Good advice here re loosening the bleeder screw. I use a six (not the common twelve) sided socket for the initial loosen. I also spray penetrating oil on the threads and leave it a few minutes (or more) in case that helps. I also try tightening just a tiny amount prior to loosening, then I work it loose, back and forth, unlike until it's completely free. I'm talking of screws that haven't been touched in decades. I find it worth a few minutes to loosen the bleeder like this than have it break off. They can be very difficult to remove once they've broken off, in my experience - all too easy to damage the caliper thread.
@michaelharland9599
5 ай бұрын
i wish i would have seen this comment last week lol. i got an 05 acura tl thats spent its life in the midwest and when trying to bleed the rear brakes the nut is seized onto the bleeder screw so it just started turning out of the caliper🤦♂️ ordered myself 4 new bleeder screws and ill be installing them tomorrow
@JSB2500
5 ай бұрын
@@michaelharland9599 The nut is part of the bleeder screw ... isn't it? 🤔
@MrGW2fanboy
4 жыл бұрын
I thought I'd never see the day where there is a DIY video as good as if not better than ChrisFix
@4DIYers
4 жыл бұрын
Thank you so much, greatly appreciated :) This is an older video too, so I have definitely increased the quality with my newer stuff.
@uncreativename9936
Ай бұрын
Thanks I didn't know about the bleeder screw attachments and was just putting the tube over the valve and was wondering why it wouldn't hold vacuum.
@4DIYers
Ай бұрын
Happy I was able to help!
@ShareXP
5 жыл бұрын
The video was made in advance and he recorded the instructions later, and was rushed to get all of the info spoken in under 4 minutes. Helpful, just had to replay a couple times.
@2RCK3
5 жыл бұрын
I got feed up with the vacuum bleeder because I had to use zip ties and Teflon tape and I was still getting a very small leak so I ended up using a 2x4 wedged between seat and the pedal to simulate a second person. Worked the first time I tried it.
@rinterstate
Жыл бұрын
To hold the brake pedal down? Thanks
@Beer_Dad1975
6 жыл бұрын
Searched for a tool like yours, couldn't find anything local so ended up getting a pro-workshop one that connects to my air compressor. Same principal though - most likely I won't use it again for several years but never mind, I still trust myself to do this job more than if I took it to a mechanic and they put the first year apprentice on it.
@bobmcl2406
Жыл бұрын
Others suggest putting grease on the threads of the bleeder screw to prevent air being drawn in when under vacuum.
@AutoTechHec
2 жыл бұрын
Im studying to take my ASE tests and very glad I looked this up. Good shit.
@4DIYers
2 жыл бұрын
Happy to help and best of luck!
@coltonware5627
6 жыл бұрын
Dude your videos are so awesome, Every time I look up a how to I hope you have a video on it!! Hopefully youll be the next "ChrisFix"
@4DIYers
6 жыл бұрын
Thank you so much, I really appreciate the support :)
@jamesnachareun6454
5 жыл бұрын
Thank you for your precise demonstration. You even outline all the necessary precautions as to perform the task. Had one of this unit, but could never get it to work even after following the instruction that came with it. Lol. Your speech was perfect. Reminds me of the infomercial on tv. Great job!!
@4DIYers
5 жыл бұрын
Thank you, I really appreciate the kind words and feedback!
@jerichotressler3771
3 жыл бұрын
Best video i have ever seen in my life
@4DIYers
2 жыл бұрын
Thank you, much appreciated!
@johannjohann6523
3 ай бұрын
Thanks for the video, one thing regretfully about this bleeder system, the instructions suck. At least mine did. luckily, I had it right all along. But, I still like to make sure before I start working on my car. It's important when you do work on your car, to first do no harm and make things worse! :)
@StringBanger
3 жыл бұрын
Really appreciate the video. Took car of my brake fluid change in wrx with ease and saved myself money
@4DIYers
3 жыл бұрын
Glad I could help and thank you for the feedback!
@HEYOKAHOUND93
8 ай бұрын
Giving this route a shot today thank you for your videos they are very informative
@4DIYers
8 ай бұрын
You're very welcome and the best of luck. Keep me posted on how it works out.
@molochonchon87
2 жыл бұрын
Short and sweet... Well played dude ... Well played.
@timklein3962
5 ай бұрын
Quick and to the point; thanks !!
@4DIYers
5 ай бұрын
You’re very welcome!
@Snenors4pres
3 жыл бұрын
Make sure your bleeder screws on your other wheels are tight 🤬 one of mine was left loose by the previous mechanic.
@420CaptainSlow
11 ай бұрын
Dude nice fricken video. The pacing and narration was great for a diy instruction video. Keep it up!
@4DIYers
11 ай бұрын
Than you so much, greatly appreciated!
@edwardcaban4881
6 жыл бұрын
Short, simple and to the point. Great video! 👍
@4DIYers
6 жыл бұрын
Thank you!
@cosmichasm
3 жыл бұрын
straight to the point, thank you
@user-ld1gc2dm9m
8 ай бұрын
Great video - straight to the point.
@4DIYers
8 ай бұрын
Thank you!
@evg_eni
Жыл бұрын
This can be used in conjunction with another method that works well. It's simple. Hang the cup on a high point. There should be some liquid in the hose (mandatory strainght vertical line). Open the bleeding plug and get in the car to pump the brake pedal. All the air will come out on its own at the highest point (the cup). You just have to be careful not to overfill the cup and not to run out of brake fluid in the master cilynder.
@joshualammi5306
6 жыл бұрын
Just enough information to keep it short enough and helpful enough. Thanks.
@4DIYers
6 жыл бұрын
Glad to help out and thank you for the feedback!
@piznigley
6 жыл бұрын
Absolutely perfect video. Very informative and not longer than a song.
@4DIYers
6 жыл бұрын
Thank you, I really appreciate the feedback :)
@wolfpackrc
Жыл бұрын
You did a great job in thus video. Straight forward well said. I wish more people made videos like this. when I do videos I try to do them like this but not successfully though.
@zaprowsdower7664
2 жыл бұрын
This vid was clear and straight to the point. Thank you!!
@milankovacs1193
3 жыл бұрын
It will work well on brakes with ABS?
@user-dc5wk8gt1b
17 күн бұрын
great vid very informative thanks
@4DIYers
11 күн бұрын
No problem!
@omarassim8176
5 жыл бұрын
Thanks for the super clear guide, straight to the point. Wish more KZitem videos were like this!!
@4DIYers
5 жыл бұрын
Thank you, I really appreciate the feedback :)
@sjlifeadventure
4 жыл бұрын
Great content bro, really helped me bleeding mine properly, thanks
@4DIYers
4 жыл бұрын
Thank you so much and excellent to hear!
@douglasthompson9482
7 ай бұрын
Excellent video
@rickcee6572
7 ай бұрын
Just what I needed, thank you!
@4DIYers
6 ай бұрын
You are so welcome!
@jdcookiemonster
6 жыл бұрын
Nice DIY, Do you not have to press the brake pedal a little to allow fluid to pump out of the nipple? I figured it wouldn't get through the master cylinder if the pedal is not pressed.
@sidichendid7237
4 жыл бұрын
YES YOU DO... I almost drove myself crazy, not realizing even with a vacuum pump you should begin the process by pumping the brakes a few times
@tech99070
3 жыл бұрын
There's a ton of nuance that could be gotten into. As an example it's a smart move to have the car tilted forward to where the front brakeline on the master cylinder is slightly lower than the one closer to the firewall. Because on a lot of cars the cylinder is mounted at an angle and there is room in the cylinder for air to get trapped higher than the secondary outlet. But how long do we want the video to be lol.
@moonrich3492
2 жыл бұрын
@@sidichendid7237 The shop manual for my 1956 Olds 98 with power brakes says, "The engine should not be running and the vacuum reserve should be depleted by applying the brake several times before starting the fluid bleeding procedure."
@Farseer1995
5 жыл бұрын
Is there any way you can think of how to seal the threads once the bleeder screw has been cracked? I turn the bleeder valve by just a mere fraction of a turn just to let a small amount of fluid leak, but the vacuum pump keeps pulling air from the threads. I have tried grease but this didn't help me. The problem is is that even with such a nifty piece of equipment, all I can see are small bubbles being pulled from the threads... I would much prefer to see bubbles and then clear fluid to indicate I did a job well done. Thanks.
@shawnnewman6035
5 жыл бұрын
Grease
@2RCK3
5 жыл бұрын
Teflon tape
@richrock455
2 жыл бұрын
nice video and straight to the point thanks
@4DIYers
2 жыл бұрын
Thank you!
@MuneebMaster
3 жыл бұрын
When checking the pedal feel, do you turn the ignition on or start the car?
@bullzeyes23
23 сағат бұрын
Thank you. My car brake pedal when press, it will slowly lost pressure that I have to repress the brake pedal again. Will bleeding the brake fluid fix it? Or the master brake pump need to be replaced? Thanks in advance.
@RetreatHacker
2 жыл бұрын
great video, straight to the point!
@4DIYers
Жыл бұрын
Thank you!
@skeeter252
5 жыл бұрын
Hi. How can we be sure that when you open the bleed screw, the vacuum pump isn't drawing air through the bleed screw threads and leaving some in the system when the screw is tightened? You say to pump the pedal to check but I really want to be sure no air is left in there. The only way I can be sure is to use a pressure bleeder but I already have a vacuum kit. Thanks.
@Celbrise
2 жыл бұрын
thanks for the video and good info. i just bought one never bled brakes before only watched and pressing the peddle. first mistake i did was not putting in the O ring so i got no suction at all. second mistake i did not pump it before opening the bleeder screw the instructions that came with my tool doesn't say any of that it just says open the bleeder and start pumping, even said it in the video. got to try again last resort i think im opening bleeders too much and likely getting air in or i have to put silicone on the nipple end due to maybe air getting sucked in from the threads? otherwise all im getting is TONS.. of tiny air bubbles and some large ones, some liquid but never a full line of it and it just is non stop just nothing but air.
@Jimidan1000
4 жыл бұрын
I have that exact same vacuum pump kit, and I tried to do exactly as you said, but it appears that there are leaks in the threads between the bleed screw and the caliper (disk) and wheel cylinder (drum rear). There is no way to seal off the tapered fittings and the bleed screw, to allow me to develop that kind of vacuum before opening. And then afterwards, I can pump all that I like and never get much fluid out of it.
@danellsworth5872
6 жыл бұрын
Great video i just bought a vacuum pump to bleed the brakes on my 4 wheeler thanks for the instructional video
@4DIYers
6 жыл бұрын
Happy to help out and thank you for the feedback!
@johannjohann6523
3 ай бұрын
Just like with their transmissions, people do not ever change out the brake fluid in their ABS system thinking the stuff lasts forever. Then the ABS light pops up and the brake pedal goes to the floor and fails to stop the car. Brilliant! The brake system will nearly last forever if you change the fluid. And getting a vacuum pump like this allows you to work on your car and save money both by skipping the repair shop, and you are providing the labor. This tool pays for itself the first time you use it, and you don't get brake fluid all over your driveway. Now that is Brilliant! All ya gotta do is change the fluids in the brake system and transmission every 60K-75K miles, and your car won't break down. Promise.
@hwhefnbebe3030
3 жыл бұрын
So happy I found this thank you!!
@4DIYers
3 жыл бұрын
No problem, happy I could help!
@omfgwtfbbq90
6 жыл бұрын
lol I kind of recognized the under carriage / suspension a little bit from my own car and as soon as I saw the pedals and the rubber mats, then I was immediately surprised I was right in my suspicion of it being an E39. I have a 2001 525d btw.
@4DIYers
6 жыл бұрын
Haha, right on! Oh you're not in North America, unless you had the car imported. We weren't lucky enough to get the diesel option, but I have seen a couple imported cars. I actually have a bunch of E39 repair videos, but sadly have sold the car :( I still have a few videos to finish up and release for the E39 though.
@tsherwoodrzero
3 жыл бұрын
@@4DIYers This may sound like a dumb question, but what did you do about the ABS system to allow fluid flow? I have an E38 (2001 740i) and everything I've read says the solenoids need to be operated via BMW DIS to bleed the brakes. Reason I ask is because I have one front caliper that is suddenly dragging (can hear it clear as day) despite no pulling to that side or other behaviors.
@Hoodhistorian562
5 жыл бұрын
THANKS BRO ! I'm about to use a pump on my 66 c10 .
@4DIYers
5 жыл бұрын
No problem, happy to help :)
@ironwill04
5 жыл бұрын
So in the video you put an adaptor on the end of the hose to go onto the bleed screw; however, when you put the hose on the bleed screw it looks like that adaptor is gone. Where you using an adaptor on the bleed screw? What is the advantage of using the adaptor? I bought this type of vacuum pump last night to bleed my hydraulic clutch and I can't get it to maintain a vacuum while when I crack the bleed screw open.
@1white870
7 ай бұрын
aweome video, bro
@4DIYers
7 ай бұрын
Thank you so much!
@motov8-garage832
3 ай бұрын
I just got a new 80$ Maddox brake billed pump kit. It won’t go past 20, then very slowly leaks down, it don’t leak down at all at 5 but 20s all it can handle apparently.. so hopefully I can get it sealed better or 20s good enough lol..I got a few months ago so I hope I can get it working good because this things in returnable now😅. I’ll try soap and water and check the whole thing in the pressure mode obviously (this one does both vacuum and pressure)
@BRORANDYMARTIN
3 ай бұрын
Do you put the cap back on the master cylinder before you bleed them ?😊
@NinerowCenter
3 жыл бұрын
This is a great guide
@4DIYers
3 жыл бұрын
Thank you!
@tealtree4019
Ай бұрын
So do you only open the bleeder screw just enough to let fluid come threw I feel as if I’m getting inaccurate readings
@adegiulio
5 жыл бұрын
Succinct, and spot on. The videography was a bit weak at times, but overall and excellent video. Thank you
@masso172
7 жыл бұрын
Are you a pilot or flight crew member by any chance?
@4DIYers
7 жыл бұрын
Nope, but I want to get my pilot's license. Why do you ask???
@masso172
7 жыл бұрын
4DIYers because your communication skills are amazing haha I'm impressed. You will have a flawless time talking to ATC
@4DIYers
7 жыл бұрын
Thank you, I really appreciate that :)
@THEGEEK2001
6 жыл бұрын
Amazingly in-depth
@4DIYers
6 жыл бұрын
Thank you!
@ocrun6765
4 жыл бұрын
You mad an excellent video. But I find that the vacuum method has a major flaw in that air will almost always seep in around the bleeder screw.
@tech99070
3 жыл бұрын
grease the bleeder and you can do it with a bit lower vacuum like 20
@ocrun6765
3 жыл бұрын
@@tech99070 that's a good idea
@IOwnedGod
5 жыл бұрын
Does it matter which wheel you start with if you're using a vacuum pump? My dad always taught me that when we bleed the brakes by pumping the pedal and having someone watch for how much fluid is coming out of the cylinder that we start on the wheel furthest from the master cylinder. Is that still true for this, or does it not matter? Thanks so much this video was really helpful. I've had this vacuum pump for years and never used it. Now I'm going to try it next time I have to bleed the brakes!! Thanks again!
@amorag59
4 жыл бұрын
Still true. Also don't forget to the seal in between the cup and the cap or else it wont hold vacuum!
@allmycarsisbroke
2 жыл бұрын
It's true for most vehicles, but not all. For example, on a 2005 Dodge Neon (this is just a specific year, make and model I'm very certain about, but there are other years of neon, and perhaps all neons, and likely several other years, makes and models of vehicles): Start with left rear tire (behind the driver's seat), then the front-right tire (front passenger). Then do right rear, then front left. If they aren't bled in the correct order, you'll never get all the air out. You can repeat this bleed pattern multiple times to be sure you're still not seeing bubbles, but just be sure to stick to this order. No idea why so many people still state so confidently and so incorrectly that the order is always the furthest tire from the master cylinder. It really depends how the brake line system is configured.
@ColonelFlickage
2 жыл бұрын
Kinda missed the last steps lol so when you pump the brakes you close the bleeder screw? Cause you said don't let it drop below 5
@exotime
3 жыл бұрын
Draw up and replace the fluid in the master cylinder if the vehicle has a few years on it, then while you bleed each caliper keep tabs on the volume in the master. Do not let it go dry .
@firmahilster
3 жыл бұрын
Nice video, but why your sweather is in frond of the action ???
@Boaters_hub
3 жыл бұрын
What about systems with abs? Will this work or does the abs pump need to be consistently pumped? I notice my pressure bleeder doesnt work because of the abs.
@insertnamehere313
2 жыл бұрын
I was told several times that if you can get fluid flowing out of the rear than it's not your abs but I sure wish someone would answer your question cause it would answer mine,I have done at least 60 break jobs only struggling with 2 but this question keeps popping up.
@o0Guns0o
5 ай бұрын
so this brake bleeder kit is just for getting air out the system right? It would probably be advised to use a power bleeder for brake fluid flushes correct?
@4DIYers
5 ай бұрын
No, it can be used for flushing the system too, it just takes a little longer because of the smaller cup.
@chrisryan8863
4 ай бұрын
How can I discern the difference in air bubbles that is caught in the line versus bubbles caused by air at the bleeder nipple whlle I'm bleeding them?
@CAROLDDISCOVER-FINDER2525
Жыл бұрын
Just let you know your video is still coming up on Google search 🔎. It is a good tutorial.
@4DIYers
Жыл бұрын
Thank you so much!
@mrsemifixit
3 жыл бұрын
You say to pump up to 25inHG, do you know why the manual for this pump says not to exceed more than 10inHG for bleeding?
@UFOGHOSTHUNTER
3 жыл бұрын
Perfect! Thanks for the upload!!
@4DIYers
3 жыл бұрын
No problem!
@footage6402
4 жыл бұрын
If you go past the minimum line, can you just start the bleeding job over again by reflushing the system? Or does it ruin it permanently by going past the minimum line in the master cylinder resovoir
@snoopdogie187
2 жыл бұрын
You just have to start over, wasting time and fluid. Depending on how low you go, you might be fine. The other issue is if air gets into the abs system. This can be a challenge and maybe not even possible to fix at home. These abs modules generally need higher level scan tools to run a program to remove the air.
@HisAssholiness
2 жыл бұрын
well done
@4DIYers
Жыл бұрын
Thank you!
@zappa916
7 жыл бұрын
can anyone tell me what the little suction cup is for?
@vegaf2011
2 жыл бұрын
So basically with this kit I won’t have to push the break ?
@randallpool7388
Жыл бұрын
THANK you!
@kylerich3771
Жыл бұрын
Gr8 video Thankyou
@4DIYers
Жыл бұрын
Thank you so much and you are very welcome!
@mattmgarza
5 жыл бұрын
I have a rounded brake bleeder screw on the passenger front wheel. If I use a self-bleeder kit like this, can I successfully bleed the brakes at the driver-side wheel ?
@dalekify
6 жыл бұрын
Thank you for the video. I wonder if you could talk a little slower. It was difficult to understand you all of the time. Perhaps it's your accent. I had to keep winding it back. Even without understanding everything you said , the video was enough to give the idea of the thing. I've not seen this type of bleeder before. You have explained it well.
@Axertion
5 жыл бұрын
You can set the speed of the video to playback slower. Just click the settings icon on the video player, and set speed to 0.5x or slower.
@DiscoGreen
5 жыл бұрын
I actually thought it wasn't even english at first.
@aleksandarmiskovic1822
5 жыл бұрын
If you guys have difficulty understanding this just go pay someone to do it he explained it really well
@Smodlee
5 жыл бұрын
It’s the way he worded it is what is making people hard to understand him
@selassiay1
5 жыл бұрын
No offense, but, I would suggest that you better take some English classes to strengthen your command of the English language. I understood the guy really well, and just to let you know, English is not my mother tongue.
@millermatic140
5 жыл бұрын
Do you have to start from the furthest brake from the cylinder with this kit or can i bleed any of them in no order
@4DIYers
5 жыл бұрын
If you're bleeding the whole system, then the furthest wheel first.
@markmarquez7348
9 ай бұрын
Would you check the brake pedal for stiffness with the car running or not running
@4DIYers
9 ай бұрын
While it’s running.
@anz3786
5 ай бұрын
Do u keep the lid on or off wen using pump thnx
@DANNY34432
4 жыл бұрын
Thank you, my dog ate my car's break line, this video helped me a lot
@4DIYers
4 жыл бұрын
Happy to help! I definitely haven't heard of that one before but have had mice eat up rubber fuel lines.
@DANNY34432
4 жыл бұрын
@@4DIYers first time for me too, now my dog isnt allowed in the garage
@tracyhill7960
Жыл бұрын
All I can say is wow
@classicskrt2422
3 жыл бұрын
I love the video!
@4DIYers
3 жыл бұрын
Thank you!
@TheDJF3
2 жыл бұрын
You you wait until you se no bubbles in the clear line?
@4DIYers
2 жыл бұрын
Yes that is correct
@deweydodo6691
4 жыл бұрын
What vacuum pump was that ? It did not look to be plastic which always seems to break .
@garrettprosser7336
4 ай бұрын
Do you leave the reservoir open or closed? While pumping
@4DIYers
4 ай бұрын
The cap is open.
@michael6692
6 жыл бұрын
very nice vid ,,, but USE WD 40 befor moveing the bleed screw ,, just a tip
@JosephMBoyer
4 жыл бұрын
I have a diesel lift pump for a fuel line... you think it would be enough vacuum for changing brake fluid?
@thevindictive6145
3 жыл бұрын
Hi can u use a vacuum pump for ac on the break fluid bleed, just modify the and not use the hand pump?
Пікірлер: 307