Very nice instructions. I purchased the bumpers for my 2021 GTX limited and was extremely hesitant to install them my self. Your video gave me the confidence I needed to get it done right. Thanks 👍
@leonardlaing6733
3 жыл бұрын
Good instructions. Nice sea-doo. Nice to see when people take pride in ownership. Thx. Also I just watched a video with you out for a cruise with Alvean over on her channel.
@YourDrawerness
2 жыл бұрын
Always start your threads by hand, especially when using an impact.
@jodytomlinson4575
4 жыл бұрын
Good video and good tips, looks like the bumpers would be a little thicker, just doesn’t look like very much protection.
@cowboybishopvids6570
4 жыл бұрын
We keep extra pads just in case you need them. In calm water at the ramp or dock this work great. But rough water you need more protection. The big pads that you tie to the bars and seat area work better for that.
@8-Tryzub-8
Жыл бұрын
So, let me understand. The way to protect the factory bumper is to drill holes in it. Makes perfect sense.
@deplorablechump8758
Жыл бұрын
Great job!
@k9sgarage301
3 жыл бұрын
what year rxtx do you have? and what was the part number for the kit?
@john94si
4 жыл бұрын
Seeing your crooked numbers brings in questions
@cowboybishopvids6570
4 жыл бұрын
Stupid thing to say when it came like that when we purchased it but typical considering this is the internet and most speak on totally irrelevant stuff. Have a nice day
@john94si
4 жыл бұрын
@@cowboybishopvids6570 just messing with ya.. The install was good. Have a good one
@CP-kb1du
3 жыл бұрын
Question when you remove them .....you have Holes in your vessel
@cowboybishopvids6570
3 жыл бұрын
The mounts are never meant to removed. It’s a permanent install
@rogertran3215
2 жыл бұрын
Does this drill through any fiberglass when you pass through the plastic portion ?
@cowboybishopvids6570
2 жыл бұрын
The rail is fiberglass
@rogertran3215
2 жыл бұрын
@@cowboybishopvids6570 do you have to put any sealant or epoxy at the end where the screw went into to seal it ?
@bgarcia856
2 жыл бұрын
I don’t know man. I seen you wiping away chartreuse paint coming out those drilled holes 😂
@Ah87100
3 жыл бұрын
No issues with leaking? Do you need to use a sealer for the screws?
@cowboybishopvids6570
3 жыл бұрын
The screws don’t go in the hull to leak. The screw is only in the railing.
@potepuhisavinjske4158
2 жыл бұрын
Hi, you have video from install speed tie 2.0
@mike04ify
3 жыл бұрын
Should I buy different types?
@cowboybishopvids6570
3 жыл бұрын
michael garcia these are fine for docking
@mike04ify
3 жыл бұрын
Why these things don’t fit good on my rxp300?
@cowboybishopvids6570
3 жыл бұрын
michael garcia not sure I have a rxpx and the fit fine on there
@tolinof79
3 жыл бұрын
If you have the mount like in this video that's why they keep falling off rxp X requires a different one
@cowboybishopvids6570
3 жыл бұрын
Flory Tolino he has the ones for the rxpx
@alejofox10
2 ай бұрын
Just want to point out that there are measurements for the distances, and I believe the one near the speaker is way to far out… But I think u did that on purpose to protect the speaker.
@cowboybishopvids6570
2 ай бұрын
We did our way because the oem instruction do not protect the speakers of the high spot on the back side
@Jetski270
Жыл бұрын
Um I’m pretty sure those screw should not be felt on the underside.
@redpineapple9908
3 жыл бұрын
I would have used a block of scrap wood behind where you're drilling, just in case. Holes in the railing are nothing, but holes in your hull are bigtime FUBAR
@cowboybishopvids6570
3 жыл бұрын
You can but a shop rag does the job plenty good. Done over200 and it’s never let us down. Drill bit just does go through fabric like a knife
Пікірлер: 31