Excellent design!!!! I'm like you, I want things simple and square every time. I don't like fiddling with things.
@jwsworkshop4169
Ай бұрын
Thanks, and thanks for watching!
@ricksmith1647
6 ай бұрын
This is the best DIY mount that I've seen. Very well done. Thank you for sharing.
@jwsworkshop4169
6 ай бұрын
You're welcome! Thanks for your comment, and thanks for watching!
@JFoxTN
Жыл бұрын
I just completed a copy of your mount for my Mega Live Transducer. I did use the Harbor Freight Low Temperature Aluminum Brazing Rods to secure the transducer mount aluminum angle to the square tube for the mount. Worked well and seems to be very strong. Just wanted to thank you again JW for a great design and your sharing it in this detailed video. Be well and tight lines!
@jwsworkshop4169
Жыл бұрын
Thanks for watching and for your comments! I like the brazing idea. Hope it works as well for you as it does for me!
@kenmccarthyfishing
Жыл бұрын
I just ordered everything through your links,thank you for having them in the description 2023 total for everything about $95 bucks,not bad, and I can’t wait to get it in and mount it to my boat,thanks again and have a great day 👊
@jwsworkshop4169
Жыл бұрын
Good luck with it and thanks for watching!
@MHDBisonFan
2 жыл бұрын
I believe I have found my new pole mount for my livescope. Just have a modification I'll have to make to my boat to mount this but now I have a plan which I didn't before. Thanks so much for this design. I like it.
@jwsworkshop4169
2 жыл бұрын
You're welcome. Thanks for watching!
@magoo72112
3 ай бұрын
Well thought out and presented. Thank you sir for you time and expertise. Greatly appreciated !!
@randyetheredge6157
3 ай бұрын
Great job and your thoughtfulness was incredible! Thanks so much for sharing this with us! I'm sure going to build one of these.
@JBHull
Жыл бұрын
Exactly what I've been looking for. Going to slightly modify for my kayak, but 99% will be same. Thank you, good sir!
@jwsworkshop4169
Жыл бұрын
You're welcome, thanks for watching!
@slynorthstar
4 ай бұрын
One of the best DIY videos and support material I have seen. Well done!
@jwsworkshop4169
3 ай бұрын
Thanks! I just fished 17 days in May and the mount is still working well. Thanks for watching!
@kernlkajun1
Жыл бұрын
I’ve reviewed AT mounts for days ranging from $100 to $500 and none of them appear to provide the overall efficiency of your superior design. A couple of years ago I followed a different design using ram ball mounts and was constantly fiddling with repositioning my Livescope transducer every single time I had to redeploy. There is no doubt that a somewhat smaller version of your design will work very well on my Hobie PA14 AT mount. Thank you for sharing!
@jwsworkshop4169
Жыл бұрын
You’re very welcome, and thank you for the very positive review. I’d like to see the kayak version! Good luck!
@lannydecamp7460
3 ай бұрын
Thank for the video.
@sssrp80
2 жыл бұрын
This is my project for tomorrow morning! I have the summit ram mount/Scotty ball. It has worked for jigging/casting but trolling is out of the picture. This is exactly what I needed to find! Plus on a pontoon I already have square tubing! Great video!
@jwsworkshop4169
2 жыл бұрын
Good luck! I’d like to see the pontoon version. Those ball mounts have their place, but I don’t think it is on the end of a 4-foot pole you want to keep square to the water all the time every time. Thanks for watching!
@berniehaynes7640
Жыл бұрын
Extremely thorough. Thank you.
@jwsworkshop4169
Жыл бұрын
Glad it was helpful! Thanks for watching!
@stevehenry9053
Жыл бұрын
YES! Thank you man I can't wait to get started on this.
@jwsworkshop4169
Жыл бұрын
Great! Thanks for watching!
@kenmccarthyfishing
2 жыл бұрын
Thank you so much for doing this video,I can’t stand the ram mount constantly moving the sec I move the boat,I can’t wait to make this 👍
@jwsworkshop4169
2 жыл бұрын
Hope yours works as well as mine do! I fought one of my original sonar units on a Ram mount moving every time I hit a wave. I wasn’t about to go that route with this heavy transducer on a 4-foot pole. Thanks for watching and good luck!
@PatrickWilbricht-ze2cj
3 ай бұрын
More info about the actual pole? The base you made is amazing. Just trying to figure out configuration of your actual pole.
@jwsworkshop4169
3 ай бұрын
I used all schedule 40 PVC. The outer pipe is 1-1/4” nominal pipe size (1.660” OD), 49 ¾” long. The inner pipe is 1” nominal pipe size (1.315” OD), 53 ¾” long. The lengths were just determined by how long was necessary to clear the bottom of the boat. At the top of the 1” pipe is a 1” Tee fitting (socket x socket x socket). For the handle connection, the tee has a 1" x 3/4" Reducer Bushing Flush Style - (Spig x Female Iron Pipe). Good luck, and thanks for watching and commenting!
@davidbonde2148
Жыл бұрын
Great design and really well done. Thanks for sharing your design and knowledge, I appreciate it.
@jwsworkshop4169
Жыл бұрын
Thanks for watching and for your comment!
@keithhill7572
2 жыл бұрын
Very nice. You did a great job designing this. I used the cycle work station mount on my Crestliner boat that was quick and easy but you have given me some good ideas for mounting solution on my Hobie kayak.
@jwsworkshop4169
2 жыл бұрын
Thanks, and thanks for watching!
@robertlivingston1634
5 ай бұрын
I think I like this design for my boat and style of fishing, especially since I already have all the aluminum and the welder.
@jwsworkshop4169
5 ай бұрын
Great! Thanks for watching!
@leroyrogers5133
6 ай бұрын
Beautiful. I was contemplating using a bike mount. But as you stated, coming into the the dock it would protrude. The problem that I currently have is stability while spider rigging. Thank you for solving this issue.
@jwsworkshop4169
6 ай бұрын
You're welcome. Hope it works as well for you as it does for me. Thanks for watching!
@malcolmzoll7613
3 күн бұрын
A very great video thank you
@tomsolem1436
5 ай бұрын
Wow great presentation enjoyed your thought process to get to your final project! Debating on DIY or buy one . Really liked your set up very solid design thank you for sharing!
@jwsworkshop4169
5 ай бұрын
Thanks for watching, and for your comment!
@tonytysk3529
6 ай бұрын
Exceptional video. Thank you. I tried to order metal and the first question was the alloy and I wondered how I could order exactly what I need to build two like you did. I am new to comments, so I am not sure how to find your list. Thanks for the great idea
@jwsworkshop4169
6 ай бұрын
If you click on “more” at the end of the video description where it shows “29k views 1 year ago,” you will see the links for the material including the alloys I used. Thanks for watching, and good luck!
@gregvaneeckhout1877
2 жыл бұрын
I really like your concept, I am trying to figure out how I can modify to use on a fiberglass ranger boat, my biggest problem is my top of gunnel is not nearly as wide as you have so I can mount it ok but may have to incorporate a al plate on bottom to give me a wider base (gunnel) and then proceed like yours? Hmmm? I still have thinking to do since also the whole plate and mount will be more exposed and protruding than yours since I don’t have the large gunnel.
@jwsworkshop4169
2 жыл бұрын
Thanks for watching and commenting! There are so many different boat configurations out there. Without seeing your boat it’s hard to guess what would work. I don’t see why you would need an additional plate on the bottom though. If you could use the outboard mounting holes into your gunnel, then you would probably just need a support leg at the inboard end of the base to your floor or side wall or something. I would envision something like a 1 ½" x 1 ½" aluminum angle leg attached to the back side of the 2” leg of the base and then somehow attached to the floor. Good luck, hope it works out!
@johnhuheey5336
Жыл бұрын
Searched hi and low for a solution, and I'm so happy to have found yours! As you said "I watched a lot of U-Tube videos that showed me how I didn't want to do it":) One question: The locating pin - you said it was a machine screw attached to the base with a nyloc nut. How does the base sit flat if there is a nut underneath the base?
@jwsworkshop4169
Жыл бұрын
The locating pin is a #10 flathead machine screw (countersunk) that comes up from the bottom of the base. The nyloc nut is what actually does the locating. Thanks for watching and good luck!
@johnhuheey5336
Жыл бұрын
@@jwsworkshop4169 Thanks for the explanation, I should have figured that out for myself. So you used the dremel to smooth out the nut.
@jwsworkshop4169
Жыл бұрын
@@johnhuheey5336 I used the Dremel to cut the screw off flush with the end of the nut and then grind it smooth so it wouldn't dig in to the square tubing when sliding it in.
@ScottRosa
Жыл бұрын
Thank you, best design I've seen!
@jwsworkshop4169
Жыл бұрын
Glad you like it! Thanks for watching!
@lorent4998
Жыл бұрын
What a great design concept!!
@jwsworkshop4169
Жыл бұрын
Glad you like it! Thanks for watching!
@odhamember
Жыл бұрын
Awesome design and explanation. Thanks for sharing or idea!
@jwsworkshop4169
Жыл бұрын
Glad you like it! Thanks for watching!
@cenlaaerialimagery6291
Жыл бұрын
Thank you very much! Very impressive engineering!
@jwsworkshop4169
Жыл бұрын
Thank you, and thanks for watching!
@edwingron-nk1ct
Жыл бұрын
Excellent video! Concise and informative. How has your design stood the test of time?
@jwsworkshop4169
Жыл бұрын
Thanks! The device is holding up well and I have not made any changes to it. Thanks for watching!
@CGTDm-h2s
10 ай бұрын
Best design and great video!
@jwsworkshop4169
10 ай бұрын
Thanks for watching!
@blakem9666
Жыл бұрын
excellent video and explanation. thank you so much.
@blakem9666
Жыл бұрын
after reviewing the comments, if your in hutcheson you definitely have fish Milford! will keep an eye out for this rig.
@jwsworkshop4169
Жыл бұрын
You are welcome! Thanks for watching!
@markdistefano6728
Жыл бұрын
Love it...Well done !!!
@jwsworkshop4169
Жыл бұрын
Thanks! And thanks for watching!
@markdistefano6728
Жыл бұрын
@@jwsworkshop4169 I have a great idea.....Make me one for my Bass Tracker 175TX. I love this design you came up with. I must have watched it a hundred times already. Seriously, if you are willing I will pay for it.
@JFoxTN
2 жыл бұрын
Excellent design JW! I just build one but the design is not as good as yours and more complicated to build. Thanks for sharing and for the concise explanation on the the build. What do you do about the cabling from the console to the bow?
@jwsworkshop4169
2 жыл бұрын
I installed the ActiveTarget module under my console. I ran the cable out from there forward towards the bow position. Where the cable emerges from down under, it is about equal distance to my two transducer pole positions. I left some excess cable to allow for stowage of the pole in the bottom of the boat. I control the excess with a heavy rubber band wrapped around a conveniently located cleat. Thanks for the comment, and thanks for watching!
@JFoxTN
2 жыл бұрын
@@jwsworkshop4169 Thank you!
@ricksmith1647
6 ай бұрын
If you don't mind me asking - how did you run the transducer connector/plug through the 1 inch pipe? The locking collar on the connector is too big to fit through the 1 inch pipe. The installation instructions that came with the unit mentioned cutting the collar and using a split collar - but they didn't provide any diagrams and I'm not sure that I understood them correctly. Thanks again for the video.
@jwsworkshop4169
6 ай бұрын
My system is Lowrance Active Target and the locking collar that came on my sonar cable measures about 0.90”. The inside diameter of 1 inch PVC is just over an inch, so it was an easy fit for mine.
@ricksmith1647
6 ай бұрын
Thank you for taking the time to respond. Your device was so much cleaner with the cable running inside it. I will figure out a way to make mine work.
@chadjansen9097
Ай бұрын
Very good! Thank you
@naturalseven5841
Жыл бұрын
Thank you
@jwsworkshop4169
Жыл бұрын
You're welcome, thanks for watching!
@paulroute8447
2 жыл бұрын
was ready to buy $259 mount till I saw this . Great Great job very good design thank you so much for sharing your brains with us. It was exactly what I was looking for
@jwsworkshop4169
2 жыл бұрын
Glad to help. Thank you very much for the comment!
@bfdude1414
Жыл бұрын
This design looks great, does this work with a rotating PVC pole for the transducer?
@jwsworkshop4169
Жыл бұрын
Yes, I used schedule 40 PVC. The outer pipe is 1-1/4” nominal pipe size (1.660” OD). The inner pipe is 1” nominal pipe size (1.315” OD). Good luck and thanks for watching!
@lduff6944
Жыл бұрын
THANKS, Great
@jwsworkshop4169
Жыл бұрын
You're welcome! Thanks for watching!
@mdrichards00
Жыл бұрын
Great video. Is there anyway I can contact you and send you a picture of my boat? I’d love to replicate this idea on my boat but I don’t have a perfectly level surface like your boat gunnel has. Would love your input, thanks!
@jwsworkshop4169
Жыл бұрын
Thanks for watching! I’m sorry but I don’t share contact info on KZitem. If you have pictures on a photo sharing site and could provide a link here, I’d be happy to try to help. Good luck!
@EugeneEdberg
Жыл бұрын
ca you tell me what the size of the outer tube is i have made all the other components ad am excited to use the transducer. thank you for your help . gene
@jwsworkshop4169
Жыл бұрын
I used schedule 40 PVC. The outer pipe is 1-1/4” nominal pipe size (1.660” Outside Diameter). The inner pipe is 1” nominal pipe size (1.315” OD). Good luck and thanks for watching!
@raymondsnell9474
2 жыл бұрын
I am just getting started trying to make something like this or should I buy something. After sending 1700.00 on activetarget it is hard thing of spend more on this. I am trying to figure out how I can modify to use on a fiberglass Bass boat. I have to go from the floor. But over all this is a great idea I like it and Not 300.00. The Ram Mount just does not look like it will hold up. Again thanks. I will let you know it turns out.
@jwsworkshop4169
2 жыл бұрын
Thanks for watching and commenting! See my previous reply to Greg. Maybe you guys can figure out the fiberglass boat mount. Good luck, hope you get something figured out!
@daviddawkins5089
Жыл бұрын
Love your design, what is the dia. of the pvc pipe
@jwsworkshop4169
Жыл бұрын
The pipe is schedule 40 PVC. The outer pipe is 1-1/4” nominal pipe size (1.660” OD). The inner pipe is 1” nominal pipe size (1.315” OD). Good luck and thanks for watching!
@kennagel3989
2 жыл бұрын
Could you explain more about the pipe? You said it was abs, correct? What diameters? How much does it move in the water? How did you attach transducer, anything special?
@jwsworkshop4169
2 жыл бұрын
The pole I made was from Schedule 40 PVC pipe. The inner pipe is 1 inch nominal pipe size. The actual outside diameter of it is 1.315 inch. The Active Target transducer attaches directly to this pipe with the hardware supplied with it. The outer pipe is 1 ¼ inch nominal pipe size. It has a nominal inside diameter of 1.360 inch. This gives .045 inch diametral clearance between the two pipes. The inner pipe can rotate freely in the water but you don’t notice any radial movement due to the fit. Hope that helps. Thanks for watching!
@keikow69
10 ай бұрын
@@jwsworkshop4169 Do you have a video of how you made your pole? Parts list/description? Great Video of the mount, I'm ordering my metal as I type this.
@jwsworkshop4169
10 ай бұрын
@@keikow69 I do not have a video of making the pole. I used all schedule 40 PVC. The outer pipe is 1-1/4” nominal pipe size (1.660” OD), 49 ¾” long. The inner pipe is 1” nominal pipe size (1.315” OD), 53 ¾” long. The lengths were just determined by how long was necessary to clear the bottom of the boat. At the top of the 1” pipe is a 1” Tee fitting (socket x socket x socket). For the handle connection, the tee has a 1" x 3/4" Reducer Bushing Flush Style - (Spig x Female Iron Pipe). Good luck and thanks for watching!
@locknowsafetyapp6620
Жыл бұрын
With thin/light steel readily available to be, any reason why it wouldn’t work good? Could paint.
@jwsworkshop4169
Жыл бұрын
I don’t know of any reason why steel wouldn’t work. I just find aluminum easier to work with and I have a good supply of it. And, I know it won’t rust. Thanks for watching!
@oldfriends2920
Жыл бұрын
I have the PVC poles made up but was looking at how to mount the PVC poles to the top square rail on my pontoon, will your design work but in a shorter form? Any suggestions is greatly appreciated! Thanks, Jeff Burkhead
@jwsworkshop4169
Жыл бұрын
Hey, thanks for watching and sorry I’m slow responding. I think my design could be made shorter, maybe even half as long. I don’t think you would lose much rigidity in the direction that is important (forward and reverse). You would give up some rigidity if you were trolling sideways. I would probably mount the device directly to your square rail through the 4-inch leg of the base. That should be pretty rigid front to back, but might need additional support side to side. Maybe an additional piece of angle aluminum attached to the back side of the 2-inch leg of the base and run down vertically to another rail of something else on the boat? Good luck!
@johnjackson909
Жыл бұрын
What size PVC did you use? Looks like a great design.
@jwsworkshop4169
Жыл бұрын
I used schedule 40 PVC. The outer pipe is 1-1/4” nominal pipe size (1.660" OD). The inner pipe is 1” nominal pipe size (1.315” OD). Good luck and thanks for watching!
@KenYoung-pu2yk
Жыл бұрын
Great Mount!! I have one problem however. I am mounting a Garmin transducer on my pole and the diameter of the inner pole is only 1" and my transducer connection to my GLS LIVESCOPE Box is 1 3/16". Any PVC pipe combination that would work so that it would fit?
@jwsworkshop4169
Жыл бұрын
If you’re using nominal 1 inch schedule 40 PVC, the actual outside diameter is 1.315”. That is what I used for my Active Target transducer. Thanks for watching!
@KenYoung-pu2yk
Жыл бұрын
@@jwsworkshop4169 I am using the I inch sch. 40 PVC. The problem is that only has a 1" inside diameter and I can't fit my Garmin transducer connector in the 1" hole, it is 1 3/16 ". Do I need to use larger pipe? What size?
@jwsworkshop4169
Жыл бұрын
@@KenYoung-pu2yk I guess I’m not familiar with mounting a transducer inside a pipe. Mine clamps on the outside of the 1” nominal PVC. The next bigger schedule 40 PVC size is 1 1/4 with an inside diameter of 1.360. That would be rather loose.
@KenYoung-pu2yk
Жыл бұрын
@@jwsworkshop4169 I'm sorry I was not clear. I'm not mounting the transducer inside the I" pipe I'm mounting it on the outside of the pipe just like you. It looks like you ran your transducer chord down the middle of your 1" pipe. Correct? I am using a 1" pvc inside a 1 1/4" pvc just like you. The problem is when I try to thread my transducer chord trough the 1" pvc pipe the connection end of the transducer chord is 1 3/16". TOO LARGE!! Is there a solution or do I have to run the transducer chord down the outside of the pipe?
@jwsworkshop4169
Жыл бұрын
@@KenYoung-pu2yk Yes, I was pleasantly surprised I could run my transducer cable inside the 1” PVC. I guess if your connection is that big, the choices are bigger PVC or run the cable outside the PVC.
@fkmovidas
2 жыл бұрын
Can you make one for a ranger tritoon
@jwsworkshop4169
2 жыл бұрын
I can’t make one for a triton but I think this design should work on any boat if you can figure out how to mount it. Thanks for watching and good luck!
@rustysmith2360
Жыл бұрын
JW, where in Kansas are you? I'm in Topeka.
@jwsworkshop4169
Жыл бұрын
Hutchinson area.
@robertgibbs5075
Жыл бұрын
Can u make one for my mega live.
@jwsworkshop4169
Жыл бұрын
Sorry but I don’t make them for anyone else. Thanks for watching!
@ATOMMIK1969
Жыл бұрын
how do u like it now, still great?
@jwsworkshop4169
Жыл бұрын
Yes, still great! I haven’t changed anything. Thanks for watching!
@ATOMMIK1969
Жыл бұрын
@@jwsworkshop4169 thank you, parts are ordered, thank you very much
@andrewwilson9932
Жыл бұрын
Do you sell these?
@jwsworkshop4169
Жыл бұрын
No, I don't sell them. I just wanted to share the idea. Thanks for watching!
@David-qo7lz
2 жыл бұрын
Nice try. Check out Hinro on KZitem.
@jwsworkshop4169
2 жыл бұрын
Thanks for watching! I saw that one. It's a good concept, but it fails to meet three important design objectives for me: 1.) Rigid when deployed (two slip fit pivot points and no obvious detent device for keeping it deployed), 2.) Cheap and easy to move the pole to a second location in the boat, 3.) Easy to store the pole in the bottom of the boat at the end of the day for no interference with the boat cover.
@nathanrichard835
2 жыл бұрын
awesome, great idea
@jwsworkshop4169
2 жыл бұрын
Thank you! 😊
@afsgary
2 ай бұрын
I have had pan optics on my boat with a homemade holder similar to yours, but there’s one issue I see! Don’t think you’re never going to hit anything with that pole in the water so after three years I will tell you you need some type of release mechanism to release the unit under pressure If you do hit a stump or something like the bottom of the pond lake a very stiff structure stump you have to rebuild that whole thing the way you’ve got it set up. There has to be some type of release or you will break the piss out of that.
@jwsworkshop4169
2 ай бұрын
Thanks for your comment. I fish a lot of trees, but I’ve only run in to tree tops which were not a problem. If I was concerned about hitting “solid” objects, I would attach the PVC pole to the angle aluminum with something that would stretch - probably some of those bungee ball cords. You might need something to positively fix the height of the pole when deployed, but then one or two of the bungee cords would keep it seated in the aluminum angle until you hit something, and then it could flex out of place. Thanks for watching!
@leftykelly3944
2 жыл бұрын
Awesome design! I have a Triton bass boat and will try to figure out how to modify your design so it will fit. Thanks for sharing.
@jwsworkshop4169
2 жыл бұрын
Hope it works out. Thanks for watching!
@myrondel
Жыл бұрын
Fantastic job, I appreciate good engineering and the KISS method. Thank you!
@jwsworkshop4169
Жыл бұрын
Thank you, and thanks for watching!
@timkeefer177
Жыл бұрын
If you ever decide to manufacture one for sale, I'd like to be your first customer
@jwsworkshop4169
Жыл бұрын
OK, thanks for watching!
@annahiggs3201
Жыл бұрын
This is great! Thank you!
@jwsworkshop4169
Жыл бұрын
You're very welcome! Thanks for watching!
@johnhuheey5336
Жыл бұрын
One question about the pole you made - is the outer sleeve 2" Schedule 40 PVC?
@jwsworkshop4169
Жыл бұрын
The outer pipe is 1-1/4” nominal pipe size (1.660” OD) schedule 40 PVC. Good luck and thanks for watching!
Пікірлер: 132