It cost me $159 with 4 bottle kit and gun. I had tape and drop cloths. Bought some etching spray from HF. It took 1.25 hours to prep including going to the store to get a wire wheel(they nylon ones took forever). Spraying was around 20 minutes each coat x2. The cheapest I found around Philadelphia was $650 and it would be 2 days in their shop. I love how it came out AND I saved almost $500 bucks. Now all my buddies want me to do theirs.
@AdventureN
2 ай бұрын
hell yeh brother!
@dylanjohnson48
10 күн бұрын
2 days in the shop that shop is crazy, line x only had my truck in the shop for 3 hours
@thepuresaltchannel
8 ай бұрын
You crushed that. Definitely not fun but so worth it.
@AdventureN
7 ай бұрын
thanks mate! no it isn't a small fun job, but definitely rewarding!
@AkumaQiu
5 ай бұрын
What sprayer are you using?
@AdventureN
2 ай бұрын
@@AkumaQiu it's called a shultz gun!
@wilen
9 ай бұрын
I'm about to paint a whole ass RV with it. I'm nervous
@boocatdog
8 ай бұрын
How did it go? Wanting do a van
@wilen
8 ай бұрын
@boocatdog it went really well, it has a very modern look, and is an easy fix to an ugly vehicle
@johnnhoj15
7 ай бұрын
By chance are you on meth?
@johnnymartinez1063
26 күн бұрын
Me too
@kr2513
6 ай бұрын
Wash the bed with Dawn let it dry. Wire wheel on a grinder (buy 2), staying away from edges. Sand as you would by your hard line. I apply Primer sealer first.
@AdventureN
6 ай бұрын
Great tips!
@kr2513
6 ай бұрын
@@AdventureNyou as well. Good on you for doing it yourself. The factory jobs aren’t even sanded before they do this, and you did a much better prep job than line-X.
@kalaganne
5 ай бұрын
Defo primer indeed
@Kernomadz
6 ай бұрын
Nice work! How many bottles did you use?
@AdventureN
6 ай бұрын
The kit came with 4, I used 3. 2 got a coat on everything but the third I went extra thick on the base of the tub
@Kernomadz
6 ай бұрын
@@AdventureNthanks for the reply! I’m about to coat my bumpers with raptor. Great video. 🤙
@NYGSZN
Жыл бұрын
My 2nd gen is a 6ft bed. Do you think I could get away with 2 cans???
@AdventureN
Жыл бұрын
I think it would be possible. but would be a very light coats
@coltsblue0331
6 ай бұрын
What psi do you recommend for this. I see the instructions say 50-60. I just want to know what you use. Look great by the way.
@sostrongineedmoreofyourmon974
3 ай бұрын
It kind of depends on what texture you desire. The higher the psi you will tend to get finer/flatter texture whereas with the lower range you tend to get a rougher/chunkier texture. Today, I sprayed my vehicle plastic trims at 55 psi (with the raptor shutz gun) and got a decently rough texture which is what I was going for. I plan on doing the same for the entire bed tomorrow, but when I raptor the exterior of my truck I know I’m going to go for 70 psi (depending on what my test sprays give me at that setting that day)
@Yash-c3v
8 ай бұрын
Doesn't it rub off with minimal use ?
@AdventureN
7 ай бұрын
no it doesn't, it's a very durable tuff coating
@matteg95
3 ай бұрын
I want to do the roof of my camper but not sure how it will bound to the roof now.
@Miles-wy1zr
6 ай бұрын
Gonna do this in June on my 95 tacoma
@JayGBee
4 ай бұрын
Get it done professionally trust me
@sostrongineedmoreofyourmon974
3 ай бұрын
Excellent! I also set myself up for June to line my entire F-150 although I pushed the start until today. Will be done with the paint project by July 4th
@Miles-wy1zr
3 ай бұрын
@@JayGBee let me pull 400 bucks out of my asshole.
@Miles-wy1zr
3 ай бұрын
@@sostrongineedmoreofyourmon974 nice bruv. I haven’t gotten to it but I will very soon
@ricardocorsa9077
Жыл бұрын
How nany cans do you recommend the kit with four cans, i have a 5.8. Short bed from chevy silverado.
@AdventureN
Жыл бұрын
The thicker the better, this kit was 4 and I any used 3 from memory. Our Ute tub / beds over here in Australia are much smaller so I’d say 4
@justinhaley9672
3 ай бұрын
How many quarts
@bensmith9175
Жыл бұрын
Roughly what was the total amount of time it took from prep to spray the second coat?
@AdventureN
Жыл бұрын
oooo good question....I really didn't make a mental note of it. Prep certainly took the longest. Spraying the easiest. Id say about 4-5hrs for prep. Then 2hrs for spray. All a gestimation
@bensmith9175
Жыл бұрын
@@AdventureN woah, you went hard on the prerp. Thanks for the info
@onetwoshootmedia
Жыл бұрын
preperation is the key to any paint job, plus I didn't want to get any paint on the new car!@@bensmith9175
@dustypaint
Жыл бұрын
do you make 2nd layer after the first one dries out
@AdventureN
Жыл бұрын
yes about 30mins dry time between the first and second layer
@kaylanwade3392
5 ай бұрын
Roll-on is where its at. Just ask project farm
@bakervinci163
Жыл бұрын
How big of a compressor do you need
@AdventureN
Жыл бұрын
To be honest I'd have no idea, something that can do a consistent 50 PSI. I guess the bigger the holding tank the better!
@apexmarketing7621
Жыл бұрын
Toff
@Clappedoutprojects
Жыл бұрын
With the price of this stuff it’s not worth doing it yourself you can get bullet liner done for 550
@AdventureN
Жыл бұрын
Whilst this is a fair comment, its more fun and having that personal satisfaction of doing a DIY project. The ability to put your hands on your hips and amire your handy work is something else in my honest opinion 😃
@dancramer7822
2 ай бұрын
It cost me $159 with 4 bottle kit and gun. I had tape and drop cloths. Bought some etching spray from HF. It took 1.25 hours to prep including going to the store to get a wire wheel(they nylon ones took forever). Spraying was around 20 minutes each coat x2. The cheapest I found around Philadelphia was $650 and it would be 2 days in their shop. I love how it came out AND I saved almost $500 bucks. Now all my buddies want me to do theirs.
@nicholssexton5426
Жыл бұрын
'promosm' 😅
@JayGBee
4 ай бұрын
Not worth all the time, effort and materials when you can get it professionally done with a warranty for around $300
@chuckbronco6485
3 ай бұрын
Where the hell are you getting a spray in bed liner for $300? The local crackhead?
@lui805
7 ай бұрын
Dont waste your time on this shyt in 20 years its going to look like azz and to restore it its a fukn pain
@AdventureN
7 ай бұрын
I certainly won't have this tub for 20 years, that's for sure!
@philipadcock3508
Жыл бұрын
@adventuren how streaky did it come out?
@AdventureN
Жыл бұрын
no streaks at all, just have to overlap your sprays abit
Пікірлер: 54