Surprisingly, 85% of video viewers haven't subscribed yet! If you enjoy my content, please consider subscribing and leaving a comment. Your engagement boosts the video's visibility. Thank you for your valuable support!
@PRITAM_MAITY
2 ай бұрын
Please add : music stop animation 🙏🙏
@HAZITECH
3 жыл бұрын
Visit my other VU Meters & Audio Spectrum Analyzer Projects here kzitem.info/door/PL4dsTE_604guMdq4JkY5jswRFKaiiRbVB
@kieranpaxton2245
3 жыл бұрын
I realize I'm kind of randomly asking but does anybody know of a good place to stream newly released tv shows online ?
@quinnmarc8230
3 жыл бұрын
@Kieran Paxton I watch on FlixZone. You can find it by googling =)
@@HAZITECH Please add extra function, if music stop will show animation
@POushoorn
Жыл бұрын
Dear Hazi Tech, I already sent a message last week with a question, but it has been deleted. I have a question about the VU meter if it is possible to use a microphone instead of a line in jack. I'd love to hear from you. Kind regards, Polle Oushoorn
@HAZITECH
Жыл бұрын
Hi. I haven’t tried it yet. I’ll keep you updated.
@POushoorn
Жыл бұрын
@@HAZITECH Dear Hazi Tech, I tried using a microphone unit instead of the 3.5mm stereo jack, but it just didn't work. I used mini microphone amplifiers from the Chinese platform.
Hey, I am amazed about your creativity working with the LEDs! What would it take to combine this project and the smart corner lamp you’ve presented recently? Could you please apply this project to the smart corner lamp execution and provide the code?
@HAZITECH
3 жыл бұрын
Hi Stefan. Thanks a lot. I’m actually working on it. I’ll share a video as soon as I’m done with it.
@crazy.chathubro
3 жыл бұрын
එදා ඉදන් හැම දාම කියන්නේ.... superb.....😍😍😍
@HAZITECH
3 жыл бұрын
Thanks brother 🤜🏻
@andrivie579
3 жыл бұрын
good job my fav channel specialist vu meter and spectrum analyzer
@HAZITECH
3 жыл бұрын
Thank you so much 😊
@anthonychairez9433
2 жыл бұрын
Hey man I just tried this out and almost got it on the first shot. I had a few wires crossed , figured it out, and it worked very well on the UNO. I currently need to play around with the code to get working with my on/off LED button setup. Should be easy to do though. Thank you very much for the easy to follow diagram. This is EXACTLY what I was looking for!! :)
@HAZITECH
2 жыл бұрын
Wow I’m so glad to hear. Thanks a lot. Please consider subscribing to the channel.
@anthonychairez9433
2 жыл бұрын
The code is pretty thick! Did you write all of that? It just so happened that I'm using 60 LEDs in my setup so it worked out of the box. One of the settings only hits 59 LEDs at max volumes / brightness / (max LED settings). I have not had a minute to glance at that section of code yet, but figure it's something that's rounding, not counting the last LED. It's the scene that starts from LED 1 and goes all the way to the end. The other settings work great and touch all LEDs. The dual LED setup is nice too. My setup is quite cool thanks to you.
@serkankaracan9014
8 ай бұрын
hi.I build this project with my student.Oonly led strip1 is working.But when ı led strip signal switch change position for two strips led 1 strip is stopped.Nothing else? ı made two 144 led strip .Please help
@HAZITECH
8 ай бұрын
You seem to have done the wiring wrong. Double check please.
@ahmetkara3763
2 жыл бұрын
Hi i made the project but it is not working.first, when i chosed atmega 328 ide ise giving error.i am chosing atmega 328 old ,this time it is not working.leds are moving without music.buttons are workin i can change the colour.but i did not understand what the problem is.sorry my bad english🥺
@HAZITECH
2 жыл бұрын
You have to connect all the resistors as in the wiring diagram to make it work
@paulinetinsley68
Жыл бұрын
I see you combine both audio channels. Do you have a true stereo version of this?
@HAZITECH
Жыл бұрын
I haven’t combined the two. This is real stereo.
@HackingInfo
3 жыл бұрын
Hey...followed exactly and it's working 😍😍😍😋😋 Just cost 1500+😣😅😅 But still worth it 😋😋
@HAZITECH
3 жыл бұрын
Awesome. Thanks for letting me know.
@sjharia007
2 жыл бұрын
one more important in this video which component or register resistance value not showing in your circuit diagram. I feacing too problem. And also Audio input and output canection diagram. Reply me..
@HAZITECH
2 жыл бұрын
You have missed the first part of the video. I have clearly shown the resistors with the colour codes there. So you can identify those easily. And you can plug any audio source to Audio In via a 3.5mm audio cable and speaker system can be plugged to audio out.
@Helloworld519
3 жыл бұрын
Good job brother. ❤
@HAZITECH
3 жыл бұрын
Thanks a lot brother 🙏🏻
@lawk3573
2 жыл бұрын
Which you use led 30led per meter or 60led per meter , if i use 60 led per meter the project is beautiful?? Or between led is very far and it's not good 😊
@HAZITECH
2 жыл бұрын
I used 144LED/m strip. Closer the LEDs, the better.
@1954charlie
Ай бұрын
My respects ! I'm Stefan and a bit old (70 years old) . I've never done a programmatic vu meter before, I'm putting the electronics together, but help me start by writing a 30 led RGB vu meter program. You installed a program that is in hexagonal form, I wanted to rewrite the number of ledds, but I can't open it and I don't know what to do! So I bought the parts, but until I know what to do next, I won't do it without a program, why? I would appreciate it if you could help ,my respects !
@HAZITECH
Ай бұрын
Hi, first of all follow exactly the wiring diagram given and wire all together. Then you have to upload the code to your Arduino Nano board using Arduino IDE software. If everything works, then I can guide you to change the number of LEDs from the code. Even you have 30 LEDs, existing code works and display patterns. We can adjust it later.
@harshwardhan4627
2 жыл бұрын
Hi Bro finally I made ur project..o came really nice how u made it..but one issue that I have seen in ur video that the patterns are more or less same..not like different ones...same it came in my project as well..I think u need to work on patterns n upload a new sketch with upgraded pattern..thanx anyways...hope to see ur new sketch...
@HAZITECH
2 жыл бұрын
Thank you so much. I’ll see what I can do.
@bajnbro
3 жыл бұрын
supiri ela hode. ස්තුතියි ඔබට
@HAZITECH
3 жыл бұрын
Thanks 🙏🏻
@monkeybytegames
Жыл бұрын
Hi, Is it possible to make a 7 band spectrum analyzer with arduino?
@aleefandrian7423
5 ай бұрын
when I uploaded, an error occurred that said "problem uploading to board". what do I have to do?
@HAZITECH
4 ай бұрын
Try changing the Arduino nano processor from the arduino tools menu.
@aleefandrian7423
19 күн бұрын
Thanks it's just skill issue
@aleefandrian7423
19 күн бұрын
@@HAZITECHI want to know, what if i change the arduino nano with arduino uno? Are the lamp work correctly? Sorry my English very bad
@HAZITECH
19 күн бұрын
@aleefandrian7423 Glad you solved it.
@robertbajan383
2 жыл бұрын
Hi .great stuff mate .haw would you connect a microphone ,is it possible with this project.thanks
@HAZITECH
2 жыл бұрын
Hi, thanks a lot 😊. Sorry, at the moment mic support is not there. I’ll do that mod soon.
@thusithaliyanage8754
2 жыл бұрын
Supirima dakshayk, Jaya 👍👍👍👍💛💛💛💛
@HAZITECH
2 жыл бұрын
ස්තුතියි සහෝදරයා 🙏🏻
@HariYanto-rh4gy
3 жыл бұрын
Mas, if the sound sensor is replaced, it doesn't connect to the audio, the scheme is changed, it remains the same, and the LIBRARY is also different or the same?
@HAZITECH
3 жыл бұрын
This works with an audio aux input. You can plug the analog out of the sound sensor module to the same audio input jack. Code and wiring stays the same.
@felixtan796
2 жыл бұрын
Hi, thanks for the great project. I have done the project based on your circuit and code, and it works well. But when i try changing the pattern or color (button1 or 2), i didn't see the pattern of moving gradient color. Can you advise? Thanks.
@felixtan796
2 жыл бұрын
Hi, I have figured it out. Set colorScheme=11 and shorten colorScheme11SpinDelay :)
@HAZITECH
2 жыл бұрын
Oh cool. Glad you fixed it 👌🏻
@MuhammadSofyan-nb9kp
6 ай бұрын
In video you use 60leds/m or 144leds/m?
@HAZITECH
6 ай бұрын
144LED/m type
@b9robot01
3 жыл бұрын
This is a beautiful project and I have already started building it. I was wondering if you have a website with complete instructions. Thank you
@HAZITECH
3 жыл бұрын
Awesome. Sorry I don’t have a website. Good luck.
@sachiramalinda8396
3 жыл бұрын
Lassanai aiye niyamai...
@HAZITECH
3 жыл бұрын
Thanks malli
@A__GARV_SAXENA
3 жыл бұрын
my setup is all ready and led is also responding on music, but the animation is not very smooth i reduce the noise and decrease the sensitivity. but it wont work :( just for information i USED Left only in one input.
@HAZITECH
3 жыл бұрын
I think there is a issue of the 5V power supply or the audio cable that you used. I also faced the same issue. Try powering the system with the Arduino Nano USB port as well.
@A__GARV_SAXENA
3 жыл бұрын
@@HAZITECH power supply is ok, i think audio cable having some issue, but colour change and pattren change is not working i already make important changes for buttons, like true/false etc. can u help in this button issue. And more query:- 1. can i use 120 led strip i mean 2 meters long led strip. 2. what is toggle peak hold works.
@HAZITECH
3 жыл бұрын
Yes you can use 120 LED strip. You need to change only few code lines. And DO NOT change anything else in the code. Everything works as it is. Just check the wiring is 100% correct and you have connected all ground wires together.
@HAZITECH
3 жыл бұрын
Peak hold turn the floating dot on and off in the main pattern.
@A__GARV_SAXENA
3 жыл бұрын
@@HAZITECH ya I changed no. Of leds. But Button is still not working.
@harshwardhan4627
2 жыл бұрын
Hi Bro..can u plz tell me if I can connect sound sensor module to the Arduino nano..so what's gonna be the change/ New program codes to compile for this..plz help me out with this..thanx n regards..
@HAZITECH
2 жыл бұрын
I'll try to do a video guide on that. Stay tuned
@nekmoon2078
2 жыл бұрын
Hi i have a question ! Can i replace 1uf capacitor by 1000uf16v capacitor? and replace 1K Ohm Potentiometer by 2k ohm Potentiometer?
@HAZITECH
2 жыл бұрын
Yes you can 👍🏻
@richie._.494
2 жыл бұрын
Can i used sound sensor instead of female jack... If yes how.. Please help me
@HAZITECH
2 жыл бұрын
It is yet to be tested. I’ll let you know.
@harshwardhan4627
2 жыл бұрын
Thanks bro for ur reply..I want to ask like can I use Two 10 k ohm Potentiometer instead of 1 K for this project...plz reply asap..thanx again
@HAZITECH
2 жыл бұрын
Yes you can 👍🏻
@harshwardhan4627
2 жыл бұрын
Thanx bro
@Bolo-Vik
2 жыл бұрын
I managed to do everything already 🙂 only the on-off switch is not working, how does it work for you?
@HAZITECH
2 жыл бұрын
Great. BTW there is no on/off switch. one toggle switch is for bouncing peak hold on/off and other one is for LED strip data selection.
@bhautikpatel4996
2 жыл бұрын
I know this one is dumb question but..can you tell me what should i connect to audio input and audio output? I am totally new for this...thanks
@HAZITECH
2 жыл бұрын
Hey. No worries. Audio input is basically a input from a audio source like a laptop, mp3 player, ipod, etc via a 3.5mm headphone cable. Audio out is the speaker device. Like a subwoofer, home theatre or even a simple PC speaker. Due to the large number of comments, going forward, I have to give priority to my channel Subscribers when replying. So, please consider Subscribing. Thank You!.
@bhautikpatel4996
2 жыл бұрын
@@HAZITECH ohh got it... thanks alot.. keep it up.you are doing great work 👍👍
@HAZITECH
2 жыл бұрын
Thank you so much.
@林廷恩-q7e
2 жыл бұрын
What an awesome project! But I have a question that what the 3.5mm Stereo female jack conncet with?
@HAZITECH
2 жыл бұрын
Thanks a lot. One jack connects with audio in from any audio source. The other one can be used as an audio out to a speaker or so. Check out my Bluetooth option linked in the video description too.
@林廷恩-q7e
2 жыл бұрын
@@HAZITECH Thanks for your feedback😍😍, so your mean is that one is connects with my phone,and the other one is connects with loudspeaker?🤔
@HAZITECH
2 жыл бұрын
Exactly 👌🏻
@林廷恩-q7e
2 жыл бұрын
@@HAZITECH thaknks!!Have a GOOD DAY😍
@HAZITECH
2 жыл бұрын
You are welcome 🙏🏻
@mojtabas4699
Жыл бұрын
Hello, how can I use the microphone instead of the 3.5 jack? Thank you for your answer
@HAZITECH
Жыл бұрын
I haven't done it yet. But you could input the mic analog out to the 3.5 jack.
@jurrace.s2032
3 жыл бұрын
Can I use 2811 pixel led for this Project? Instead the 2812b? Thanks for the video and the information! 😊
@HAZITECH
3 жыл бұрын
Yes of course. I’ve used it. kzitem.info/news/bejne/q6ZqxWqneoqKhpg
@soundon2513
Жыл бұрын
Can I use smd5050 led strip instead of ws2812b led strip?
@HAZITECH
Жыл бұрын
Sorry you can’t. You have to use a pixel LED strip.
@jukiosss
2 жыл бұрын
Excelente proyecto...quedo genial 👍 Habra versión 2.0 con más efectos de luz?
@HAZITECH
Жыл бұрын
Muchas gracias. Intentaré hacer la versión 2.0.
@DavidpietrO
3 жыл бұрын
NIce job Man! I want to make a similar project, but with 200 LED powered by rechargeable batteries for a 4 hours use each time. Can you suggest a power supply solution to my project?
@HAZITECH
3 жыл бұрын
Awesome. You could use a 5V mobile phone power bank like with 10000mAh capacity. Make sure it can output at least 2A.
@ugochukwuokafor3764
Жыл бұрын
Failed to compile as i was using a cheapo Arduino board. Any way i can make it to work?
@HAZITECH
Жыл бұрын
What is the compile error?. Make sure you install the relevant libraries first.
@madurdananjaya5705
3 жыл бұрын
supiri wadak👌👌👌
@HAZITECH
3 жыл бұрын
Thanks 🙏🏻
@slelectronic1254
Жыл бұрын
Gammak thama kollo.. ♥️♥️😍
@HAZITECH
Жыл бұрын
Thanks bro
@tommechelmans7672
2 жыл бұрын
when you switch from signal what is the diffrens between the 2 led strips.
@HAZITECH
2 жыл бұрын
When using single strip mode, you can basically turn the next led strip on with the exact same design.
@karanbawa1110
3 жыл бұрын
Hello this is a great project...I have a quick question, in the design you show 1 switch but in the construction I can see you have 2 switches, what is the 2ns switch for? Thanks
@HAZITECH
3 жыл бұрын
One switch is for peak hold ON/OFF. The other switch is for strip selection for two strip stereo or one strip stereo.
@karanbawa1110
3 жыл бұрын
@@HAZITECH Thank you is there a wiring diagram you can share so that I know how to connect the 2nd switch. Thanks and much appreciate your prompt response
@HAZITECH
3 жыл бұрын
It is linked in the video description.
@karanbawa1110
3 жыл бұрын
@@HAZITECH yes but that diagram only has one switch, where do I connect the 2nd switch. Thank you very much
@HAZITECH
3 жыл бұрын
Please take a look again. There are two.
@KevinGroninga3D
3 жыл бұрын
I completed this build and everything seems to be working except for Mode 3. In this mode, the Left Channel and Right channel don't appear to run the same and something looks like there's an error in the code, I'm using 2 strips of 60 LED's and have the select switch in stereo mode. When i change it to run in Mono (both sides run from the Right Channel), then it seems that both sides are working the same, Is there a small bug in the code perhaps?
@HAZITECH
3 жыл бұрын
Hey, glad you made it. I'll check the code and get back to you.
@KevinGroninga3D
3 жыл бұрын
@@HAZITECH, cool! Would it be helpful if I shot a short video of my build and how mode 3 appears ‘odd’? And btw, having that JPG image of the schematic was super helpful in doing the wiring!
@HAZITECH
3 жыл бұрын
Yeah that’s great. Send the video to my HAZI TECH Facebook page messages. And you are welcome.
@raulrg1208
Жыл бұрын
hi i have the same problem, did you find the solusion
@KevinGroninga3D
Жыл бұрын
@@raulrg1208 no, never got a solution except for mono mode.
@mizzyayadelavigne
2 жыл бұрын
How about ws2811? Can do it like that follow the pattern beat ?
@HAZITECH
2 жыл бұрын
Yes. You can use WS2811 with the same way with the same code.
@spaceblack5296
2 жыл бұрын
I need in this project on ESP8266 Module with only 1 input 3.5mm audio jack without any buttons (60 led strip) Error: showPeaksPins was not declared Please bit modify code on showPeakPin and paste in comments section please please please please
@HAZITECH
2 жыл бұрын
This system is anyway designed for one 3.5mm input. Other one is for audio out. Removing the buttons wouldn't be that straight forward. Patterns are connected to the button positions and so on.
@Xhhynn1168
3 жыл бұрын
It's awesome!! Cool project. I want to make it too😁. I'm amazed by it😍. Just wanna ask how long was the led strip?
@HAZITECH
3 жыл бұрын
Thanks a lot. I used 144 LED/m LED strips and used 60 LED pcs. It’s about 40cm long.
@Xhhynn1168
3 жыл бұрын
@@HAZITECH thank you!😊 God bless for more cool DIY projects.
@HAZITECH
3 жыл бұрын
Thank you so much.
@harshwardhan4627
2 жыл бұрын
Hi Bro..can u tell me if I can use mic sensor module connected to the Arduino nano...what would be the change / New program codes to compile..plz help me out with this..Thanx n respect..
@HAZITECH
2 жыл бұрын
You could use the existing codes. Choosing the right mic module is the key. Give the mic module output to audio in port of the system.
@SathishKumar-rh9hc
7 ай бұрын
hi, i have a doubt. Can i add a mic sensor and make it react to it's input? And can i make a visualizer from a matrix of leds? Thanks in Advance!
@HAZITECH
5 ай бұрын
You should be able to add a mic. But cannot use with a LED matrix without a major code update.
@SathishKumar-rh9hc
5 ай бұрын
@@HAZITECH I am planning to use esp8266 with wled, can i use it?
@TMRu22311
2 жыл бұрын
Awesome Project! I am wanting to use a 3.3FT 144(2X72), so each tower would have 72 leds. Would I need to uncomment the 2x 144 and use that, Or should I use the 2x 60 and adjust it to 72? I am just confused because the 144 WS2812B strips have led's much closer together than other strips. I apologize if this is a simple question, I am still new to Arduino :/ Thanks my Friend
@TMRu22311
2 жыл бұрын
I think I figured it out. I would use settings for a single 144 strip and adjust the code to work with that. #elif defined (led_strip_144) //settings for a 144 led strip int stripNumOfLeds = 145; int stripsOn2Pins = true; uint32_t stripColor[73]; int displayMiddleLed = false; int splitStrip = true; int middleOffset = 1; int startupAnimationDelay = 1; int orangeLimitAmount = 0; int swapLeftRight = false; Does this look correct?
@HAZITECH
2 жыл бұрын
You are almost there. Anyway, I have modified the code for you. Please go to the updated link in the video description. And don't forget to share the video and support me. Thanks!.
@TMRu22311
2 жыл бұрын
@@HAZITECH THANK YOU! THANK YOU! I would be happy to share your projects with others. Most people don't even reply to question (let alone update code to help), you Sir are a wonderful person. I know it can get frustrating hearing the same simple questions over and over, but we all have to start somewhere, Thank you :D
@HAZITECH
2 жыл бұрын
Super thanks for your compliment. I’m honoured.
@hexaltheelektro4054
3 жыл бұрын
what if i use 5 rgb led strips? and what is the function of the potentiometer for? Thanks bro...
@HAZITECH
3 жыл бұрын
You can use any number of pixel LED strips in parallel. Potentiometers for controlling the brightness of the LED strips and adjust the audio response.
@rencymartacazon3309
2 жыл бұрын
Is the code working for 15 led two strips? I am making this right now...
@HAZITECH
2 жыл бұрын
Yes of course. You have to do a minor code adjustment to change the number of LEDs. Select 60 LED option and then look for that function. Then change 60 to 15 and 31 to 8. That’s it.
@dineshsampath9907
3 жыл бұрын
Me wage 10 band spectrum analyser akak hadannat kiyala dennako Hoda channel akak mma nithara balana tanx
@HAZITECH
3 жыл бұрын
Sure eekath langadima dennam. 🤜🏻
@ylectronics7133
3 жыл бұрын
Good day my friend. You've made an extraordinary project using arduino. Instead of using 5v 2a power supply, can I use 5v 3a power supply?
@HAZITECH
3 жыл бұрын
Thanks a lot. Yes. You can use any ampere power source above 2A as long as the voltage is 5V.
@ylectronics7133
3 жыл бұрын
Thanks a lot! You are nice and responsible for people who are asking questions about your project. Keep it up💪😁
@HAZITECH
3 жыл бұрын
Thank you much. Please share my videos and help me to increase my KZitem community. Thanks 🙏🏻
@qr2197
3 жыл бұрын
Hi. I made it with two 144 led strips and the only problem I have is that the first 16 leds on each strips are way brighter than the rest. Any idea why?
@HAZITECH
3 жыл бұрын
You have to give 5V power to both ends of the LED strips for even power distribution. Try that.
@mruotomasyon768
8 ай бұрын
the same problem occur mine...
@HariYanto-rh4gy
3 жыл бұрын
Mas itu untuk skema lo mau bikin pakek sensor suara pa harus di ganti skema nya dan libary nya juga
@HAZITECH
3 жыл бұрын
See my reply to your other comment 👍🏻
@ugochukwuokafor3764
2 жыл бұрын
How do you adjust the lights to work with only bass and cut off other frequencies
@HAZITECH
2 жыл бұрын
Sorry it is not that straight forward. It requires heavy code update.
@ugochukwuokafor3764
2 жыл бұрын
What if i add a capacitor to the audio input to block out the mid-high tone so that only the bass frequency can go through. Would that work?
@HAZITECH
Жыл бұрын
Yes. That is a very good solution. It should work.
@Budho8434
Жыл бұрын
Can I use 10k potentiometer instead of 1k
@HAZITECH
Жыл бұрын
Yes you can 👍🏻
@Budho8434
Жыл бұрын
@@HAZITECH hehe boi
@simantosd
Жыл бұрын
This really works 10k potentiometer instead of 1k?
@HAZITECH
Жыл бұрын
Yes
@StoneTL
3 жыл бұрын
On the video you're using two led strips but when you show the code you were uploading for one led strip. How come ? Or you connected them in parallel ?
@StoneTL
3 жыл бұрын
I need both channels to work. Left and Right.
@HAZITECH
3 жыл бұрын
With one strip also you get the stereo effect. If you take a look at the wiring diagram you can see there is a switch to select the data line to the strips. With two strips you get more design options.
@HAZITECH
3 жыл бұрын
Audio source goes to audio in (eg. Phone, Laptop, etc). Audio out goes to speakers. And based on your requirement, you may need only one.
@HAZITECH
3 жыл бұрын
Audio IN and Speaker OUT
@StoneTL
3 жыл бұрын
@@HAZITECH can it support 2 led strips and 144 leds both? I've tried two 60 leds, it works fine. But when I set 144 and create a new "define for 144" it doesn't work at all.
@finnjo1590
2 жыл бұрын
Hey. Can I also use a normal arduino uno? It also has a ATmega328 as the arduino nano, right?
@finnjo1590
2 жыл бұрын
By the way dont judge me. I know nothing about this stuff. I need to do this for a school project.
@HAZITECH
2 жыл бұрын
Yes you can use a UNO without any issue. You are welcome to ask any question. As a support, please consider Subscribing to the channel by clicking on the link below. Thank You!. kzitem.info
@@HAZITECH thankz aiye..👌👍❤️ Me wage 10 band spectrum analyser akak hadannat kiyala dennako..
@HAZITECH
3 жыл бұрын
Ok bro wede patan aran inne 😉
@amilaruwan81
3 жыл бұрын
Drigeme aka tiyenne ban
@HAZITECH
3 жыл бұрын
Mekai malli mulin mama diagram eka video eke dala thibbata wenama description eke dala thibbe ba. Eekai Supun malli kiwwe. 👌🏻
@erykobniski5140
3 жыл бұрын
hello, I want to connect it to the cinch in the car. can I switch to RCA (cinch) instead of aux? Very nice design, thank you 😊
@HAZITECH
3 жыл бұрын
Yes of course. Make sure you give L and R audio signals. And connect RCA ground with the device ground.
@erykobniski5140
3 жыл бұрын
@@HAZITECH thank you very much 😊
@HAZITECH
3 жыл бұрын
You are welcome
@erykobniski5140
3 жыл бұрын
@@HAZITECH and can I divide the 120 LED strip 1 meter into 4 parts and connect it in series?
@HAZITECH
3 жыл бұрын
Yes. You can use any combination. All you have to select the right no of LEDs per strip in the code.
@dinumadushan
3 жыл бұрын
Good job brother
@HAZITECH
3 жыл бұрын
Thanks a lot brother
@seancastro2416
7 ай бұрын
nice one bro👍👍👍
@HAZITECH
7 ай бұрын
Thanks a lot
@milosgagic4820
Жыл бұрын
Hi, how can i add effects to work separately from VU meter, so i can have both?
@HAZITECH
Жыл бұрын
That would be a total new coding. You could use a secondary arduino nano board and feed the data to the strip with a toggle switch.
@milosgagic4820
Жыл бұрын
@@HAZITECH Well, that is a great idea, it is easier for me now, if i don't find method how to switch between two codes/modes. Thanks anyway!
@HAZITECH
Жыл бұрын
You are welcome 👍🏻
@jhvaleriano
3 жыл бұрын
Bom trabalho. Tens duas resistências 330 Ohm no audio in e audio out que conectam no arduino A0 e A1 e no gnd, isso está correcto? ou é algum erro no diagrama? obrigado
@HAZITECH
3 жыл бұрын
Oi, o digrama está correto. Esses resistores devem estar lá para aterrar o ruído quando não houver entrada de áudio. Boa sorte.
@jhvaleriano
3 жыл бұрын
@@HAZITECH Obrigado Hazi Vou também fazer esse VU
@МестныйУмелец
3 жыл бұрын
Very good job 👍🤝.
@HAZITECH
3 жыл бұрын
Thanks a lot 🙏🏻
@asyarialfan5305
3 жыл бұрын
the light keeps on, the schematic is correct, what's wrong?
@HAZITECH
3 жыл бұрын
If you do the wiring correctly and uploaded the code there shouldn’t be any issues. Try adjusting the sensitivity knob.
@milosgagic4820
2 жыл бұрын
Nice job! Can i use more than 2 rows of led strips but they would be shorter?
@HAZITECH
2 жыл бұрын
You can connect any number of strips in parallel. But if you use shorter strips, the full effect won't be visible.
@milosgagic4820
2 жыл бұрын
@@HAZITECH Thanks for the answer. Subscribed!
@HAZITECH
2 жыл бұрын
Awesome. Thanks 🙏🏻
@milosgagic4820
2 жыл бұрын
@@HAZITECH Hi, i have one more question. Is audio out used for connecting Nano with amplifier/speakers?
@HAZITECH
2 жыл бұрын
Yes exactly
@AmitRaj-zz9vp
3 жыл бұрын
Brother can I use less no. Of LEDs on each channel Like 15 no. Of LEDs on each channel.
@HAZITECH
3 жыл бұрын
I think I have to modify the code to enable that. Let me check and get back to you.
@ravitheboss4636
2 жыл бұрын
I'm looking for the same
@ravitheboss4636
2 жыл бұрын
I need code - to use 15 leds each channel ( 15 left + 15 right) if possible please update
@hearttouching414
2 жыл бұрын
❤❤❤❤
@HAZITECH
2 жыл бұрын
Thanks
@edoha3646
3 жыл бұрын
Amazing!!i dont have 1k potentiometer does 10k 50k or 100 work?
@HAZITECH
3 жыл бұрын
Thanks 😊. 10k works 👌🏻
@RDCST
2 жыл бұрын
Those LED strips are the ones with 60 per meter?
@HAZITECH
2 жыл бұрын
No those are 144LED/m type.
@RDCST
2 жыл бұрын
@@HAZITECH Never saw it. Thanks!
@HAZITECH
2 жыл бұрын
You are welcome
@SLcreativeelectronics
Жыл бұрын
ඒත් මේකට ardiuno nano board එක වෙනුවට ic එකක් program කරල දාන්න පුලුවන් නම් හොඳයි පුලුවන් නම් එහෙම එකක් ඕනේ
@HAZITECH
Жыл бұрын
Mokakda IC ekak dana eken balaporoththu wenne brother?
@SLcreativeelectronics
Жыл бұрын
@@HAZITECH Nano board ekak danna viyadama vadi ne
@SLcreativeelectronics
Жыл бұрын
@@HAZITECH Eka board ekakin eka project ekai ne karanna venne
@HAZITECH
Жыл бұрын
Nano eka Rs.900 withara order karaganna puluwan. IC dala ithuru parts daddi eeta wada cost eka yanawa.
@SLcreativeelectronics
Жыл бұрын
@@HAZITECH Mokenda order karanne
@jesusmata1977
3 жыл бұрын
buenas noches, muchisimas gracias por tu proyecto. Tengo un problema, y es que al encenderse los led´s, me ocasiona un ruido parásito en los altavoces. Tengo conectado las resistencias y el condensador tal como pones. El condensador es de 2,2 uf. Y tengo un potenciómetro de 10k. Cuál puede ser el problema?, si los led´s no están encendidos, el audio hace bypass perfectamente, pero al iluminarse los led´s, vuelve el ruido, como el de un grillo.
@jesusmata1977
3 жыл бұрын
Me respondo yo mismo, el problema estaba en la salida analógina de mi PC, no sé el motivo pero sin tener las tiras encendidas, el bypass no tenía ruido de fondo. Así que ahora entra el audio a través de la salida usb de una tarjeta thx de unos auriculares razer kraken y funciona sin problemas
@HAZITECH
3 жыл бұрын
Es muy agradable saber que resolvió el problema. Genial y gracias por los comentarios.
@juanenriquemorosoli2730
2 жыл бұрын
hola, se pueden poner diferentes medidas (cantidades de led ??),, borrando los comentarios en el soft ? solamente esas oopciones hay ? tenes algun proyecto de analizador de espectro o alguno q me puedas recomendar con estas tiras y arduino ??? muchas gracias
@HAZITECH
2 жыл бұрын
Hola amigo. Puede cambiar la cantidad de LED descomentando las líneas en el código. Y puede encontrar más proyectos siguiendo el enlace a continuación. kzitem.info/door/PL4dsTE_604guMdq4JkY5jswRFKaiiRbVB
@juanenriquemorosoli2730
2 жыл бұрын
@@HAZITECH hola, gracias !! tengo una duda, sirve la tira de led WS2812 ?? sin la "b"final ????
@HAZITECH
2 жыл бұрын
Due to the large number of comments, going forward, I have to give priority to my channel Subscribers when replying. So consider Subscribing. Thank You!.
@AbdulRazak-gy3mg
Жыл бұрын
Tolong skema cara membuat nya..
@vinothram
2 жыл бұрын
Hi can we use esp32 for this project is it possible
@HAZITECH
2 жыл бұрын
I’m not totally sure as I haven’t tried. Sorry
@swapnaaxom1359
3 жыл бұрын
why you don't shell it on amazon
@HAZITECH
3 жыл бұрын
Unfortunately due to lack of time.
@JosePerez-pk6go
2 жыл бұрын
Tengo una duda acerca de los dos jacks 3.5 como se deben conectar, a las bocinas?
@HAZITECH
2 жыл бұрын
Debe conectar la salida de audio de una fuente de audio a uno de los conectores de 3,5 mm y conectar el altavoz al otro conector de 3,5 mm.
@JosePerez-pk6go
2 жыл бұрын
@@HAZITECH Algo asi me imaginada, la conexion solo es un puente, correcto?
@tapha7274
2 жыл бұрын
i want to make 1 led strip (60 leds), how do i do it?
@HAZITECH
2 жыл бұрын
You can select it in the code. Please read the comments in the code. Due to the large number of comments, going forward, I have to give priority to my channel Subscribers when replying. So, please consider Subscribing. Thank You!.
@ashwanthhobbyist2587
3 жыл бұрын
Can I used ws2811 pixel led, at the same code
@HAZITECH
3 жыл бұрын
Yes you can
@amazonbaru4841
3 жыл бұрын
Nice project bro👍 Can i ask how to count the resistor that Will be use..? I look in the other project you use the resistor is different.🙏
@HAZITECH
3 жыл бұрын
Brother the resistors connected to the LED strip is 330 Ohm (D4, D5 pins). All the other are 10K.
@amazonbaru4841
3 жыл бұрын
@@HAZITECH an than the Watt..? 1/2 Watt or 1/4 Watt or 1/8 Watt.?
@HAZITECH
3 жыл бұрын
It doesn’t matter. Use 1/4W as it is common and cheap.
@amazonbaru4841
3 жыл бұрын
@@HAZITECH although the number of LED used is different whether the size resistor remains are same ...?
@HAZITECH
3 жыл бұрын
Yes
@AD-hy3ij
3 жыл бұрын
Awesome bro
@HAZITECH
3 жыл бұрын
Thanks a lot
@vivekedits01
2 жыл бұрын
How much total mode in this controller
@HAZITECH
2 жыл бұрын
Please take a look at the demo at the beginning of the video. It shows all the mods.
@HackingInfo
3 жыл бұрын
very detailed and easy to understand video
@HAZITECH
3 жыл бұрын
Thanks a lot 😊
@HackingInfo
3 жыл бұрын
@@HAZITECH one question...if you have 2×60 LED strip then why upload that first one 60 led with 2nd one commented?🤔
@HAZITECH
3 жыл бұрын
Two LED strips can be worked as a single strip or as two channels. So if you see my demo, you can see in the first half both LED strips work as one. Then in the second half they work independently.
@HackingInfo
3 жыл бұрын
@@HAZITECH I got that demo part....my question is if I uncomment that 2nd strip then should I comment 1st single stripe and then replace all that single strip variable with 2nd stripe variable which defined? Or the variable already present in loop?.... Isn't then variable missmatch error? So confused 🙄🤔🤔
@HackingInfo
3 жыл бұрын
@@HAZITECH okay now I got that after deeply observing the code....you already defined those variable settings with *#if** define* and *#elif** define* 😋😅
@rikshitdutta1074
3 жыл бұрын
Audio in and audio out that jack in circuit diagram ???
@HAZITECH
3 жыл бұрын
Both jacks are identical and you can use any one as audio in. Then the other is audio out.
@simonslyk8350
2 жыл бұрын
Hi can you help me i hay lots of errors when i build your code. I hav included the libary from your link but there are 47 errors. Please help me and thanks for your video
@HAZITECH
2 жыл бұрын
If you install all the libraries and do exactly as in the video there shouldn't be any errors. Can you copy and paste the full error message here.
@simonslyk8350
2 жыл бұрын
@@HAZITECH can I sand you screenshots per email? Because it is to much for KZitem commentary
@HAZITECH
2 жыл бұрын
Sure 👍🏻
@simonslyk8350
2 жыл бұрын
@@HAZITECH I sendet the scrennshots by email. But today ist working on the Arduino software but not on PlatformIO on Visual Studio Code. Thanks for your help and your fast answer. Like and Abo
habría alguna posibilidad de que comentaras como añadir efectos de luz nuevos?. Tengo un código arduino con más efectos luminosos pero no sé que tendría que copiar y pegar en tu código. Te lo puedo mandar a algún correo para que lo veas y ver si se puede incluir en tu código?. Un saludo.
@HAZITECH
3 жыл бұрын
Lamento decir que agregar nuevos diseños requeriría una codificación completamente nueva y será una tarea que llevará mucho tiempo. Así que, lamentablemente, tienes que lidiar con los diseños actuales.
@amilaruwan81
3 жыл бұрын
නියමයි ඔබට ජය.
@HAZITECH
3 жыл бұрын
බොහොම ස්තුතියි
@raisaa2017
2 жыл бұрын
Mas bro audio in dicolokan ke kabel salon trus audio out kemana
@HAZITECH
2 жыл бұрын
Gunakan satu jack 3.5mm sebagai input dan lainnya sebagai output.
Ekanam hithaganna amarui malli mokada nano uno dekema ekama chip eka use wenne. Wena board ekak nedda try karala balanna
@linodhesandu8791
2 жыл бұрын
Man oyage Arduino programme eka mage board ekta upload krnna yaddi error ekak enawane ai ayye ee (sketch_aug07b.ino:4:31: fatal error: Adafruit_NeoPixel.h: No such file or directory) me error eka
@HAZITECH
2 жыл бұрын
Malli code folder eke thiyana arduino library tika install karan inna mulin eeta passe code eka upload karanna.
Пікірлер: 532