Dzieki dobry człowieku za ten film ,dzieki niemu zmotywowałeś mnie do zaprojektowania takiej spęczarki tylko że dużo wiekszej o głębokości roboczej 350mm. Jeszcze raz dzieki. Pozdrawiam.
@TomTheBuildR
6 жыл бұрын
;-)
@jdwisdom9433
2 жыл бұрын
This video does not show the internal lever mechanism that is the heart of the machine. That's a little on the dumb side and certainly important to the build.
@APOSTOLOSTSAROUHAS
6 ай бұрын
Good job. I made one like this. It is impossible to give me the dimensions?
@BushImports
6 жыл бұрын
Did you get those Jaws from Eastwood? That turned out nice, thanks for sharing.
@rogerbridges8921
2 жыл бұрын
Grate job 🌝
@autotechnika718
5 жыл бұрын
Większa głębokość robocza to same plusy jak rozumiem ? Czy do tego można założyć jeszcze jakieś inne końcówki czy raczej tylko spęcznianie ? Jak się na tym blachę 1mm obrabia ? Warto brać blachę wysokotłoczną czy zwykłą ?
@-ded-disel-2575
3 жыл бұрын
Proszę o link do sprzedaży tego urządzenia Dziękuję.
@Portrayalpress
4 жыл бұрын
Gloves? I don't need no stinkin gloves....
@piotrandrzejewski363
6 жыл бұрын
Podjął byś się wykonania samej góry pod szczęki na zamówienie?
@shezpaul
6 жыл бұрын
Looks good, shame it doesn't quite function the way it should. If you have to jump on the leg press like that I feel you have the leverage all wrong.
@TomTheBuildR
6 жыл бұрын
Thanks for comment. Not quite... If you look on majority of movies on YT everyone is shaping thin aluminium sheets... and it goes nice and fast... But if you want to strech or shrink steel that's different story. You need to put large force and spend some time on each piece of metal... This is not a matter of levers it is a matter of material that is being shaped. I tested various dimensions of levers and I think this is optimum.
@shezpaul
6 жыл бұрын
I understand and respect your reply.My apologies if I came across rude. Can i ask what ratio you have. I believe 45 to 1 is the standard for hand leverage but as the leg muscle is stronger is the same leverage required. Thanks and kindest regards paul
@rockerpat1085
5 жыл бұрын
@@TomTheBuildR I agree with you that there is nothing wrong with your leverage. What I see is you're to deep into the jaws. Try only shrinking just the outer edge of your piece. Lazze has a good video about not going in too deep and how if you're trying to make a curved piece just shrink the outer edge. Makes it easier and it's how it works. Great build and thanks for posting this video!!! Keep Rocking it out!!!
@lotussuperseven6239
3 жыл бұрын
👍👍👍👍👍👍
@jimb0w-garage251
4 жыл бұрын
hi ! where did you get the jaws ? Nice project ;-)
@TomTheBuildR
4 жыл бұрын
Hi, thanks :-) I bought them on the internet: www.allegro.pl kind of "polish" ebay
@jimb0w-garage251
4 жыл бұрын
@@TomTheBuildR allegro.pl/oferta/szczeki-speczarka-rozciagarka-do-blachy-prasa-7006525530 i found these ones ? Do the quality of parts is good enough ?
@Reparaturkanal
4 жыл бұрын
This is not the correct item - Yours is a single part, where the sheet metal cannot slip thru - Used on the stretcher in the video is a two piece part, where the upper and lower parts are separate.
@jimb0w-garage251
4 жыл бұрын
@@Reparaturkanal In the begining of the video, you can see that it is a one part model. I think then it has been separated to allow big metal sheets to be shaped.
@Reparaturkanal
4 жыл бұрын
@@jimb0w-garage251 I see you're right. Heliotech sells them, and the two piece units have four screws on each unit.
@habitual2245
Жыл бұрын
Well that was stupid, I could have fabricated that little piece at the end in half the time it took you to make that machine.
@The1mybuddy1
Жыл бұрын
Bet you were severely disappointed after that project was finished. All that work amd material wasted to do something you could have done just as easy with a pair of pliers with a machined block on the end. GEESH.
@leoerenata1
4 жыл бұрын
Good night, can you send the project? pdf or dwg I am grateful, I need to manufacture one of these.
@TomTheBuildR
4 жыл бұрын
Hi, Sorry, I've made it without any drawings so I do not have any. Regards
@wasserglatte3696
5 жыл бұрын
Well done, but no power enough to press easily the Metall. Never welt without Gloves !!!
@policedog4030
5 жыл бұрын
Good!
@kamilkosek4086
6 жыл бұрын
Witaj, posiadasz jakiś projekt lub szkic spęczarki ?
@adam.z.3609
6 жыл бұрын
kamil Kłosek Tu masz coś podobnego kzitem.info/news/bejne/162N3mippWiHqmU a na jego fb profilu jest zwymiarowany projekt spęczarki+rysunek na zrobienie tych szczęk
@Abaddon664
6 жыл бұрын
Witaj, gdzie kupowałeś szczęki? ;)
@TomTheBuildR
6 жыл бұрын
Cześć, na Allegro. Wystarczy wpisać "SZCZĘKI SPĘCZARKA ROZCIĄGARKA" i pojawią się ogłoszenia. T.
@abelpaucarsolis4723
4 жыл бұрын
No puedo ver las medidas
@leoerenata1
4 жыл бұрын
Боа ное, подвире о проекте? pdf ou dwg фико грато, Preciso Fabricar Uma Dessas.
Пікірлер: 38