It is guys like you that will push your country forward and I salute you. A word of advise, both WELDING and heating “spring” steel will weaken the metal, that’s what caused your “snap”.
@justanamerican9024
3 жыл бұрын
You are right. It is tricky but it can be tempered to retain much of its strength
@mvblitzyo
4 жыл бұрын
really enjoy that the builder is so persistent on making that tool work great build !..
@user-qe2es8mw5m
4 жыл бұрын
굿 ~~!!역시 아이디어가 좋아요
@user-mv2sj6ud4v
4 жыл бұрын
역시 최고 입니다.
@johnsandoval347
4 жыл бұрын
Never gave up! Don't ya just love a project like this... Bravo!
@jgyoung1981
4 жыл бұрын
Try adding stiffeners on the edges and sides. Think like a c section piece of steel bent into your s shape. It will make the piece much stronger and safer and still allow the clearance you need. Be safe friend.
@803Garage
4 жыл бұрын
Great video. I love how you showed the progression as you improved your jack setup. Thanks.
@trackrunner11
4 жыл бұрын
I appreciate his effort and ingenuity but thus is as exciting as watching grass grow.
@humblehombre9904
4 жыл бұрын
You should re-heat that entire part, then temper it properly. After bending it and working it, you likely caused the metal to have internal stresses and flaws, possibly small cracks. Something to remember for future? This is, however a very good idea.
@renemirguet1464
4 жыл бұрын
Soudeur professionnel . Super travail !
@valterleao6795
4 жыл бұрын
Parabéns pelo trabalho, quanta habilidade e criatividade! Abraço aqui do Brasil 🇧🇷
@user-wz8oe3xx2g
4 жыл бұрын
많은 것을 배움니다 다양한 용도로 사용가능하겟습니다 저는 목공 작업시 사용하거나 물건이동시 아전하게 드는용도로 사용하겟습니다 항상 응원하겟습니다
@yanani5460
2 ай бұрын
достойно..Зачет!
@knightofcamelot5173
4 жыл бұрын
Отлично приспособление. Желаю вам удачи и терпения.
@knightofcamelot5173
4 жыл бұрын
@@choigotv001 друг я с Казахстана,если когда не будь будешь здесь, напиши встречу.
@abramfehr6800
4 жыл бұрын
At 13:26 😂😂😂
@Rom567dff
4 жыл бұрын
Удачи любви и терпения все пока ваш нагиев
@truckerx100
4 жыл бұрын
Skilled metal working and impressive results! Champion of a low cost build
@alexxxx9221
4 жыл бұрын
Nice colours
@franciscoguevaragaldamez1011
3 жыл бұрын
Megusto la persistencias bendiciones
@ashqelon7267
4 жыл бұрын
This is a real guys life that shows ingenuity is still is around and WORKS. ‘And add in hard work.
@billarroo1
4 жыл бұрын
That correct, not everyone wants to go buy a toe jack just to do your own projects Especially when U have the ability and knowhow to make your own, "Ingenuity", when that bend snapped off, it just needed annealing, U did that when U welded the piece back on. I guess 7018 ? Good Choice. Great Video.
@johnhili8664
4 жыл бұрын
@@billarroo1 That's the problem he thinks he has the ability and the know how which he doesn't have thats why he nearly got killed!!!
@toninhosuprema6321
4 жыл бұрын
Muito criativo gostei ..genio
@damonsmith7297
4 жыл бұрын
🤔 maybe the solution was the I-beam you was working from. Great job! Impressive torching skill.
@viliemaciel622
3 жыл бұрын
Ótima ferramenta parabéns
@wallyallyn5473
4 жыл бұрын
Third time's a charm!!!!!
@nichosena5942
4 жыл бұрын
Anyone who has worked construction like I did can see much more uses for this jack than just to lift this metal storage unit great idea
@ioanpopa3943
4 жыл бұрын
Nicho Sena cum sa demontez electromotoru la citroen sara 1, 9 dizel
@MrThenry1988
4 жыл бұрын
No helmet? Grinder and paint can make one the welder they ain't. Worked good enough.
@FlyGuy2000
4 жыл бұрын
The face shield is OSHA approved so he's good to go.
@mulyadimul3017
4 жыл бұрын
No
@user-ni8hl9qq2i
4 жыл бұрын
쟈키는 있는데 생각치못한 기술 인정합니다 참 잘하셨네요 산소절단기는 없지만 노력해보겠읍니다. 감사합니다
@readmore3634
4 жыл бұрын
Most of the comments below critique his work...but if you look close....he still has a job....
@---1366
4 жыл бұрын
고장봉으로 지져대니까 되는군요. 대단한 집념입니다. 지게차값 벌었네요.
@Bluehill-daepark
4 жыл бұрын
역시 아이디어샘입니다
@MrGoodtrav
4 жыл бұрын
I like your work and I like how instead of an auto dark hood you have an atomic left hand to cover welding flash. Creative
@TitoTito-ju1te
3 жыл бұрын
Raw potato slices on those red sore eyes overnight and by the morning as good as new.
@shepherd_worldwide
4 жыл бұрын
변형 아이디어에 특출나신 분이십니다. 그동안 각고의 노력으로 해박한 지식과 역량을 갖추느라 얼마나 고생을 하셨을지 눈에 선합니다.
@shepherd_worldwide
4 жыл бұрын
@@choigotv001 기술이나 인격에도 품질과 수준이 있게 마련이지요. 앞으로도 놀라운 실력 발휘해주시기 바랍니다.
@johnharvey4496
4 жыл бұрын
Funny video, it's like... where's it gonna break this time. Barely any design strength tolerance. but full marks for perseverance. Luck there's not much stuff in that container.
@jamesanderton344
4 жыл бұрын
Useful tool...truck springs have a very high carbon content....the spring broke where the heated area was embrittled.
@asoomtia
4 жыл бұрын
That's right
@billarroo1
4 жыл бұрын
Just needed annealing, that happened when he welded that piece back, 7018 ? I guess?
@FlyGuy2000
4 жыл бұрын
@@billarroo1 7016
@timwegman5776
4 жыл бұрын
Yup I seen that coming when he never dipped it
@rogerrajaram6693
4 жыл бұрын
@@timwegman5776vfñhmmnnh
@arseniosifontes5878
4 жыл бұрын
Interesante....saludos desde Venezuela
@user-bi8fu7mj8i
4 жыл бұрын
외국영상인줄ㄷㄷ
@gordonclark7632
4 жыл бұрын
Out of the box thinking, a chance to use his tools and what do you do with the jack after you have used it?
@joewoodchuck3824
3 жыл бұрын
I didn't see why it couldn't still be used as regular jack. The blue attachment comes off, right?
@idolodenaro7102
4 жыл бұрын
Molto ingegnoso, semplice e funzionale
@thomasshirley5046
4 жыл бұрын
You have some of the best blow torching skills ive ever seen. Excellent job on jack. Engineering mind. Great skills
@secondlooksformen3836
4 жыл бұрын
Nice to read a positive comment about a worker's ingenuity and hard work. He solved problems and succeeded with the tools and skills he had to work with. I found it interesting, but that's just my opinion. But, I also learned a lot from all the experts' critiques..
@paullogieri248
3 жыл бұрын
Apparently you haven't been around welders/fabricators that actually know what they're doing.
@williamta9408
4 жыл бұрын
Great video ! Safety glasses. ...
@lorenzopena1919
4 жыл бұрын
Buen trabajo
@jongyoonoh6721
3 жыл бұрын
아주 좋은 아이디어네여... 해외에서는 컨테이너 개작 창고나 집을 많이 하니까..인기가 있군요.
@waynesmith9765
4 жыл бұрын
FINALLY! Someone who uses a cutting torch. Thumbs-up!!
@mannihh5274
3 жыл бұрын
That lift hook certainly needs a proper heat treatment. I wonder, why the bricks didn't crush - always put some wood between bricks and iron.
@abeldasilvasilva4268
4 жыл бұрын
Muito bom sua ideia valeu irmão
@manuelberrezueta4447
4 жыл бұрын
ñ Mm mm:
@lawrenceallanwilkie4898
4 жыл бұрын
Seals in that Jack are done. Finished.
@sojournsojourntraveler1203
3 жыл бұрын
Something I learned to do starting when I would brake springs on my Caterpillar tractor walking beam, is like your blue part / spring steel when finished cutting and bending on it is to heat the entire part good and hot and stick it in isolation over night . This annealing process takes the tension out of the work and it won't break again nearly as easy or often. Good Video Thank you
@The1roofer1
4 жыл бұрын
Nice design and nice work !!
@leonsv2964
3 жыл бұрын
Такими донкратоми, оригинального исполнения Я пользоволся при монтоже оборудования в 1988г немецкого производства. Идея очени нужная,это есть нулевой подьём.лайк.
@Qt_Jang
4 жыл бұрын
금손 이시네요^^ 참 머리가 좋으십니다... 어떻게 그런 생각을 ㅎㅎ
@PRR5406
Жыл бұрын
Excellent solution and great tool.
@omarfarsha5886
4 жыл бұрын
Necessity is the mother of invention. I'm planning to use my everlast welder to make something similar to raise parts of my concrete sidewalk.
@thardyryll
4 жыл бұрын
Omar Farsha How much does Neverlast pay you to post your comment?
@gamerphonline8219
4 жыл бұрын
Crisanta daleon
@EdyBKL
3 жыл бұрын
Good like....👍👍
@curtwarkentin6167
3 жыл бұрын
Excellent idea. I need to level some sea cans at my farm and can sure use something like this. Thanks for the idea
@felipe_garage
4 жыл бұрын
Canal seu estilo cars deixando aquele like
@akqj10119
3 жыл бұрын
잘봤습니다 구독좋아요 꾸욱하고갑니다
@billthompson9595
3 жыл бұрын
great idea! i have never seen stick welding done like that before. GOOD LUCK
@jasonjason4497
4 жыл бұрын
You did a great job! Very useful tool! Thank you!!!
@channel2belas59
3 жыл бұрын
Kreatif banget gaes
@jayk.2928
4 жыл бұрын
What a great idea!!! One of the best I've seen, it's simple but effective.
@youngbaeoh7417
4 жыл бұрын
수고하셨어요.
@Alisnafi67
3 жыл бұрын
عاشت الأيادي ،، احسنت عملاً يا بطل
@baxinhoaloprados3056
4 жыл бұрын
Era óbvio que o Jig iria quebrar, fez a dobra aquecendo a peça, isso fez com que a peça perdesse sua têmpera e não fez novamente a têmpera e o revenimento, perdeu a dureza e resistência.
@barrybrady6814
4 жыл бұрын
In fairness to him he got his job done so he is a winner
@andresantosneto4269
4 жыл бұрын
Ótimo vídeo que Deus abençoe
@NaturalpersonSB
4 жыл бұрын
안녕하세요? 고생은 하셨지만 잘 만드셨네요. 저도 기계,공구만지는거 좋아하는 사람인데 어찌 이방법은 안했을까? 란 생각이 듭니다. 땅파서 작기집어넣고 조금씩조금씩 올려서 또 고이고 올리고 고이고 이방법만 고집했으니 제 머리가 안좋은가봐요. 잘 배웠어요. 영상 감사합니다.
@NaturalpersonSB
4 жыл бұрын
@@choigotv001 추가 꿀팁 감사 합니다.
@luiscesarsilvapereira8649
4 жыл бұрын
나는 또한 몇 가지 미친 일, 자동차의 수소, 태양 에너지, 적은 원자 폭탄 ha hahaha 나는 브라질에서 왔어요, 곧 see겠습니다!
@kevinaldcroft6291
4 жыл бұрын
My heart was in my mouth when that metal lifter you made broke, that could have been a trip to hospital. Talk about on the edge of your seat video.
@geraldoceliodamasiodossant7742
4 жыл бұрын
The idea is what commands, very good!
@smithysmithy1
4 жыл бұрын
OMG Edit Man!!
@pramodsinha3981
3 жыл бұрын
Very good bro।
@AffordBindEquipment
4 жыл бұрын
I wonder how well that weld stuck to the cast iron base?
@teomejia2032
3 жыл бұрын
Really simple
@teomejia2032
3 жыл бұрын
Using the right type of rots
@frankaguilarris208
4 жыл бұрын
16'30" imprudencia total... Que pasaría se se llegará o romper de nuevo y cayera el contenedor sobre su mano? Ufff Sin embargo. MUY BUENA IDEA CON RESPECTO AL GATO HIDRÁULICO. ÉXITOS!! !
@ThanhNguyen-ou1cg
3 жыл бұрын
Có sáng tạo nhưng cẩu thả trong kỹ thuật rẩy dễ xa nghề. Rất nhiều cẩu thả, trong đó cách cầm viên gạch thứ nhất đưa vào chêm chịu tải, đưa vậy, cup ben đội bể hay thanh sắt câu bị gãy thì bàn tay cầm viên gạch sao nhỉ. Hihi
@MP-mt8lc
4 жыл бұрын
Make sure you remove the hydraulic oil from the vessel before welding, if the oil is left in and excessive heat is applied from the welding it could cause the oil inside the cylinder / vessel to explode.
@ksja2
3 жыл бұрын
탄소강이라서 불 먹으면 쉽게 부러지니까 템퍼링 해야 되죠. 산소로 살짝 달궜다가 천천히 식혀주면 좋습니다. 워낙에 재주가 좋으셔서 뚝딱 만드시네요. 발톱 자키가 가격도 싸고 좋은데요.
@holdurhorse9149
4 жыл бұрын
Watching his way of trial & error to come up with the right size plate to resist 4 tons of shear vertical Force is invitation to self inflicting permanent impairments!
@gobawo5904
4 жыл бұрын
헐~ 놀랬잔유.. 강하면 부러진다 인가요..자동 강한 열처리가 되었나 봅니다.낚시바늘은 너무 강하면 탄성이 없어 잘 부러지죠..적당한 탄성이 있어야 대물도 낚을 수 있죠..탄성이 너무 많으면 펴지죠..용도에 따라 철의 성질을 달리 제련하듯이...제활용에 큰 의미는 없지만요...선생님 발상의 전환에 늘 한 수 배우고 갑니다.감사합니다.
@@user-fg5ki4mq1c 너무 강해서 부러진것 입니다 서서히 식혀야 하는데 물을 뿌리셨다면 휘어질틈이 없이 깨진것 이지요
@Glasnot1
3 жыл бұрын
nice DIY for shoe jack / toe jack. although this could be improvised with continues welding and higher grade of steel but overall is solid work. use guard for grinder for your own safety, and use face shield for welding, you could get skin cancer and broken cornea for doing that very long. i could send you one if you need it.
@dannymcphee
4 жыл бұрын
Necessity is the mother of invention. Perhaps that's all he had to work with.👍👍👍
@swain99
4 жыл бұрын
Doesn’t give up easily does he 👍👍👍👍
@LeosTueftelei
4 жыл бұрын
Good idea and a nice job ! 👍 🙋♂️
@billarroo1
4 жыл бұрын
"Ingenuity still thrives", Not everyone wants to buy a toe jack just to do your own projects, Especially when U have the ability and knowhow to make your own, when that 90 degree bend snapped off, it just needed annealing, U did that when U welded the piece back on, 7018 I guess? Good Choice, Great Video
@TheHHAndreas
4 жыл бұрын
Why am I watching this??? Have no jack, no container, no burner, no welder, no need to lift a 40ft container. Need to watch the vid again, to find out......
@tubergenmotorsports4193
4 жыл бұрын
That's funny! Welcome to the Internet. I like to try to pickup bits and pieces of knowledge of whatever people are making or doing.
@secondlooksformen3836
4 жыл бұрын
@@tubergenmotorsports4193 perfect response. I learned several things from what is being done. Also, learn even more by reading comments. Most are knowledgeable and well intended by experts. I don't agree with calling someone stupid because we disagree with how they do things. To me, ignorance us not necessarily stupidity. He may just lack training and is doing the job as he was taught. Hopefully he can learn to do a better job and be safer before he or someone else gets hurt. I wish him well.
@valeraomelchenko8559
4 жыл бұрын
На шток цилиндра происходит односторонняя нагрузка - или шток будет согнут, или направляющая станет овальной и масло будет течь.
@user-xm5hw8cy2c
4 жыл бұрын
Красавчик! Для решения конкретной задачи пойдёт. Тем более поднимает не все 5 тонн, а только угол и кратковременно ;)
@valeraomelchenko8559
4 жыл бұрын
@@user-xm5hw8cy2c, домкрат должен оставаться таким, как им он был "таким он и остался". Когда тяжёлая единица поднимается, точка опоры перемещается - ещё больше нагрузка на шток, чем сам вес и, если не ошибаюсь, в конце ролика, шток возвращался с трудом.
@user-ud7ft8vn2i
4 жыл бұрын
Вот кусок швеллера от реж уже готово всё по деаганали лишнее от реж и всё гнуть ничего не нужно
@Helmet_Tester
3 жыл бұрын
Love this. My wife is Korean, and when we take trips to see the family I think I get an ulcer every time. They are the most care free thinkers around. All they tell me is ....Ahh it's ok don't worry.
@alphaforce6998
3 жыл бұрын
Worrying about what? Seems like you're the wife. :D
@Helmet_Tester
3 жыл бұрын
@@alphaforce6998 Ah look it's another guy on the internet lonely because he has no friends. Trolling to make a funny. Did you Nut?
@alphaforce6998
3 жыл бұрын
@@Helmet_Tester Are you so insecure that you require the perceived validation of other people to feel adequate?
@luzolivares6568
4 жыл бұрын
I like the fact that your crafty as hell. Equipment failure is normal you can't win them all the time nice job
@suebsueb966
3 жыл бұрын
Q
@bobnation9799
4 жыл бұрын
I am so fortunate to have equipment, material, safety supplies, and experience to complete these types of projects. Forget sometimes how good I have it.
@pedrovision6987
3 жыл бұрын
You did OK buddy...problem solved...innovate, improve, implement...
@josemachado3007
4 жыл бұрын
Têm gente que não gostou mais é nota 10
@user-ct2li7ud7c
4 жыл бұрын
해외에서 더인기있을줄 예측했다니까요
@eduardolecea6703
4 жыл бұрын
WOW my friend you are really GOOD...Thanks for share!
@redfield312
4 жыл бұрын
i .worked with a friend at hights that used to tack weld without a helmet always said he shut his eyes in time . he was blind 1 year latter with burns to the back of his eyes DONT DO IT
@nigelmitchell351
4 жыл бұрын
The strongest steel section was staring him in the face.!
@oldtrio1
4 жыл бұрын
AMAZing Homemade
@onefixitman
4 жыл бұрын
This guy is just using what resources are available. No money. Just lots of time. No words about safety.
@kxf250rf
4 жыл бұрын
Proof that some of the best welds are made without using a welding helmet. Just close your eyes and hope for the best. Luckily you don't have to worry about the welds holding up because I'm sure you burnt the seals out of the jack when u welded the top
@jafarkhaleghian6506
4 жыл бұрын
همه مطالب عالی، متنوع، آموزنده و درحد سپاسگذاریست، پرسی از همه دوستان
@jeremiasgomes9038
4 жыл бұрын
Sucesso
@Cypsmen
4 жыл бұрын
Nice !
@horste9237
4 жыл бұрын
You should cut out the base plate so that the blue piece can go all the way to the ground. And some safety precautions while welding should not be too expensive.
@andycapp8843
4 жыл бұрын
An interesting video and many lessons can be learned from its’ production. The boring element is reading the first few mindless comments from keyboard warriors, many of which are simply repetitions of the previous in order to display knowledge they don’t have to impress others they don’t know.
@paullogieri248
3 жыл бұрын
What's your source of knowledge, Andy?
@andycapp8843
3 жыл бұрын
@@paullogieri248 Are you looking for assistance with a problem Paul, why do you ask?
@paullogieri248
3 жыл бұрын
@@andycapp8843 I need no assistance. I' was looking for at least some anecdotal evidence that you yourself are not a "keyboard" warrior". It's not as if the sun rises or sets on what you might say. Let it it be sufficient to say that design, analysis and fabrication of welded structures is not something I need lots of help with, and if I do need help I know many people who are amply qualified. Let the greater point be this: the guy in the video - probably driven by lack of resources - devised a dangerous device and built it in a substandard way. It's irksome and a bit frightening to see so many people who (apparently) can't see the danger in his methods and result. That's all.
@richardclare700
3 жыл бұрын
@@paullogieri248 As I said originally, an interesting video with many lessons to be learned. The post neither criticised nor supported this guy's work but was directed at the mindless repetitive comments from the warriors. If you do at some time require qualified help from professionals, the company I sold 13 years ago will no doubt oblige. They played around with a few structural fabrications for around 40 years, hotels, offices, that sort of stuff. You asked for my knowledge source when it wasn't really necessary in reality, having read the post again.
@paullogieri248
3 жыл бұрын
@@richardclare700 My reason for asking was to ascertain Andy's own status of "keyboard warrior" (or not) from your pronoun choices in the latest post I gather that "Andy Capp" is a pseudonym you've used. I'm satisfied that you two are well qualified in this area - but I am in need of no assistance.
Пікірлер: 816