this channel deserves way more subscribers!! brilliant content! keep it up!
@integza
5 жыл бұрын
Thank you so much Bradley :D
@geisterwolfsa
4 жыл бұрын
It’s criminal... this channel is aaa quality! I hope he keeps it up!
@Tlcunha81
4 жыл бұрын
I was thinking the same thing. The amount of hard work he puts in his channel is great. I always learn a lot! Thank you for your videos, Integza!!!
@ChicagoRacerJoe
3 жыл бұрын
Very impressive!!!!👍
@skeet7075
3 жыл бұрын
@@integza this aged like fine wine
@rus0004
4 жыл бұрын
"A drinking game you say?" *Looks at length of video.* *Looks at bottle of cheap Scottish battery acid on the shelf.* "Might just spectate this round."
@hubertnnn
4 жыл бұрын
Looks like Scotland have some nice names for their drinks. Last time I was there I got a beer called "Used engine oil"
@TheActionBastard
3 жыл бұрын
I was thinking to myself "...if i played with alcohol I might well be dead by now" halfway through this video.
@burieddeep5557
3 жыл бұрын
Can confirm drinking is a bad idea, not Making that mistake again
@CristiNeagu
4 жыл бұрын
Also, soldering tip (pun intended): Get the parts hot before you melt the solder. That way the flux covers them and the solder flows over them. Your trouble at 7:42 is because you weren't heating the pins.
@paulcohen1555
3 жыл бұрын
And don't use fake cheap chinese flux and solder.
@mandi8345
3 жыл бұрын
@@paulcohen1555 also also, clean the tip with a bit of brass wool, de-crap it with flux and tin it with a small bit of solder. Dirty tips give bad solders.
@OlivierLopezCh
5 жыл бұрын
7:42 buy some soldering flux dude, your life will change forever
@integza
5 жыл бұрын
The saddest part is that I use flux XD
@OlivierLopezCh
5 жыл бұрын
Oh... what an awkward moment...
@integza
5 жыл бұрын
@@OlivierLopezCh Awkward was when I tried to sing ahahah
@OlivierLopezCh
5 жыл бұрын
@@integza That was beautiful. For a moment I thought my wife was playing Andrea Bocelli in the living room
@pauljs75
5 жыл бұрын
Also ditch the round iron tip. Seems the guys that do circuit stuff a lot (EEVblog or Big Clive are the ones I watch) say round soldering irons kind of suck. An angle tip is better for transferring the heat.
@faab007nl
5 жыл бұрын
i counted you saying "Torque' 33 times
@integza
5 жыл бұрын
That's a lot of chocolate milk!
@MrRyanroberson1
5 жыл бұрын
@@integza if we do the math, eight 1oz shots = 1 cup, so that's 4 cups = 1 quarter gallon, about 1lb of milk, .45 kg ~ .45 L
@maxwfk
4 жыл бұрын
@@MrRyanroberson1 i thougth about doing the game with vodka i have laying around but after this comment im glad i missed out on that
@MrRyanroberson1
4 жыл бұрын
You made me realize I underestimated the volume by a factor of 2. 1 pound = 1 pint, so it's more like .96 L
@maxwfk
4 жыл бұрын
Ryan Roberson that would have been more than I have here at the moment (and that’s good. Nobody needs more alcohol at home at a time)
@senorcapitandiogenes2068
5 жыл бұрын
I have died 4 times now from the drinking game. Expect to hear from my non-existant lawyer, señor cactus, when he finally stops shooting gatling lazors from his flying cyborg shark
@dergonmcdragon3161
4 жыл бұрын
Captain Diomedes wut a cyborg shork
@rus0004
4 жыл бұрын
Damn, I'm gonna have to play New Vegas again.
@CursedSouthwest
3 жыл бұрын
Uh...
@zanefraser714
3 жыл бұрын
Don't use alcohol. Use chocolate milk. You won't die 9 times and wait for you t Rex lawyer to be done shinning a dime for a jumping goat is going to get you 45 bucks for a heart attack as the cause of deathcyther 5g jaggy rock solid wall
@Whatsthegeek
5 жыл бұрын
Your channel deserves to have soooo many more subscribers. Your content is super interesting and original. Really refreshing tbh ^^
@integza
5 жыл бұрын
Thank you so much :D
@MrTomasMaliauka
4 жыл бұрын
You make me laugh even though today is a really difficult day for me.
@baen.
4 жыл бұрын
Sorry man
@colleenforrest7936
4 жыл бұрын
Your weight is swinging. Doesn't this add swing weight?
@Bruno_Noobador
3 жыл бұрын
Same
@Mikehoncho191
3 жыл бұрын
I’m a year late, but I hope you are feeling better
@harrysheppard3745
3 жыл бұрын
@Macho Sancho couldn't have said it better myself
@eigenman2571
5 жыл бұрын
Alright. I got my glass of milk, turned up the volume, let’s do this! [edit: Ugh... I give up... this is too much milk for me!]
@integza
5 жыл бұрын
And too much liquor for me XD
@Tallisman1000
4 жыл бұрын
That’s because milk is denser than most other liquids... works well in betting games
@user-vy5hc9ud6l
3 жыл бұрын
1l milk is not that much for a time i drank 1.5l a day
@seba007_
4 жыл бұрын
I gave up after emptying a can of tea... THORQUE!
@lvb3575
4 жыл бұрын
Aw man I really enjoy your content, I hope the KZitem algorithm is nice to you and that your channel explodes. Because this is some quality content
@integza
4 жыл бұрын
Thank you so much for that :D
@joshuaoneil9989
3 жыл бұрын
Over the course of 3 days you have become one of my favorite youtubers, such awesome ideas and builds! I’m a recent mech engineer graduate and had no idea what projects to work on until I seen your videos.
@ferrumignis
5 жыл бұрын
Great project! The friction brake using PLA may be problematic, it's friction is likely to vary as it heats up. Closed loop control of the clamping force e.g. a stepper controlled by the arduino could be an interesting development. You could also try a much simpler way of measuring torque with no load cell required; simply use use a large enough flywheel with known (or measured) moment of inertia, and measure the angular acceleration caused by the motor.
@integza
5 жыл бұрын
Thank you :D I actually thought of measuring the angular acceleration and is a great idea but in the end, I opted for a more direct way of measuring it :D
@Mabh838
3 жыл бұрын
Very good combination of technical and Comedy : brilliant explanation of static vs dynamic torque
@solveit1304
4 жыл бұрын
I already love this channel. Also if you soldering, first touch with hot iron tip pads and pins. Then after 2 seconds start melting solder! Your pads are too cold to solder, you must preheat it! That's why solder not sticking to board :)
@juancagonzalezt60x
5 жыл бұрын
I just discovered this channel, and let me tell you, it's awesome. Educational and your sense of humor is on point
@integza
5 жыл бұрын
Thank you Ruan :D
@tilation3853
5 жыл бұрын
Hello from Germany, i pretty much love your Videos. Please never Stop doing that! And i have a little tip for your Solderskills: If you soldering THT-Parts you have to heat the Board and the Pin at first and after 1-2 seconds you can apply the solderwire. It is also a good idea to use a solder-spnge to hold the Tip clean.
@integza
5 жыл бұрын
Thank so much for the compliments and tips :D
@xSchattenfluchx
5 жыл бұрын
@@integza Additional tip: There is no such thing as "too much flux" Also, I love your video, always laughing my butt off and still learning stuff
@peerappel2012
5 жыл бұрын
@@xSchattenfluchx I don't completely agree with you on that. Flux also leaves a dirty surface behind. You can clean it but yeah, if it's not neccesary... :-)
@dreggory82
5 жыл бұрын
@@integza , your soldering skills are fine but it looks to me like your soldering iron tip sucks, making it difficult to solder well. I use this: www.amazon.com/X-TRONIC-XTR-4040-XTS-Digital-Soldering-Station/dp/B003TC8EQS and I love it. It heats up pretty fast (30 seconds, I timed it just now). The tips can take some serious abuse (I have left it on at 320 C for almost a week on accident and the tip was fine), the tips don't erode and they stay tinned nicely over a large area (to me, the tinning on the tip is the biggest factor for nice soldering besides temperature), plus it has a hot-air rework station so that you can solder and desolder BGA, SOT, SOIC, TSSOP, QFN, Etc. IC's and components with multiple tiny pins. I also highly recommend using water soluble flux, I like to use: www.amazon.com/Chemtronics-CW8300-Water-Soluble-Dispensing/dp/B0091VQ3U0/ref=sr_1_20?crid=2Z32MTN98X0V3&keywords=water+soluble+soldering+flux&qid=1552184438&s=hi&sprefix=water+soluble+%2Ctools%2C210&sr=1-20 you can clean it off your board with water and a toothbrush, then dry thoroughly with fast air, I have used: www.amazon.com/XPOWER-Airrow-Multipurpose-Electric-Duster/dp/B07MV1GSTT/ref=sr_1_3?keywords=electric+air+duster&qid=1552184667&s=hi&sr=1-3 or you can use a hairdryer with a reduction or set the drying PCB in a bag of rice/descant for a while. but for soldering my process is always: -Clean the soldering iron tip by stabbing a copper scrubby a couple times (scrubby available in the cleaning isle at the supermarket). -Add a tiny amount of new solder to the tip (for best heat coupling) -Touch both pad and component with the tip, using the side of the tip that has the most solder hanging on. -Add more solder on the opposite side using the smallest amount of solder to do the job (I recommend using a small gauge solder wire for more control). the last step is optional if there is enough solder on the tip, and you are using liquid flux/flux paste. In fact this is how I solder multiple tiny pins on say an SOIC chip. I cover the pins and pads with flux, load up the iron with solder, and then drag the iron across the pins. The surface tension of the solder in the flux keeps the solder from sticking across the pins. Anyway, your skills are fine, you just need some better equipment, I might have done worse with what you were using.
@luisca92
4 жыл бұрын
I love you. This is quality quality stuff. I'm ajust getting started in open source engineering and your content has become something I look forward to every video you post. You not only educate but I like you as a personality. Keep it up!!
@TheSuperDeuce29
3 жыл бұрын
Good work man. Your content is exactly what we all need more of. Especially the youths that need direction. Keep it up and thank you for sharing this with the world.
@mickdejay5183
3 жыл бұрын
When I first watching this video I could only make it to 5mins before I passed out. With practice and now a fully fledged alcoholic I can now watch it to the end. Yay!!!!
@kj_H65f
5 жыл бұрын
I just discovered your channel yesterday when looking up info on turbines. What a gem! I subscribed within watching one video. You clearly put a ton of effort into your content and you're pretty damn funny too :) Great content! I'm going to tell all my engineer friends about you channel, I hope you get many many subscribers!
@integza
5 жыл бұрын
That comment made my day! Thank you so much :)
@Bednar121
4 жыл бұрын
Want the solder to stick to pins better? 1. Lower the soldering iron temperature 2. First heat up BOTH the pad and the pin with the iron, then apply solder 3. Use flux (either solid flux, or paste, whichever You prefer)
@spacecowboy74
4 жыл бұрын
I ran out of liquor trying to play this godforsaken drinking game.
@NicolasSalencPBP
5 жыл бұрын
Holy crap this channel is awesome! I subscribed after 5 mins watching this video! Keep it up! 👍
@integza
5 жыл бұрын
5 min? What took you so long? Thank you :D
@danielbozarth7232
4 жыл бұрын
Fricken got me with the mayonnaise analogy 😂😂
@humbertokokoa11
5 жыл бұрын
I have been waiting for this video. It's very interesting and educative. The song was very funny hahaha. I was the like 100. I think it's an honor for me hahaha.
@integza
5 жыл бұрын
Its an honor for me! Thank you for always commenting and liking the videos. I can only pray for more subs like you :D
@humbertokokoa11
5 жыл бұрын
I don't understand how other KZitem channels, that their content is not as good and dedicated as yours, they have many subscribers. Your channel should be more popular. Actually I follow you on Instagram😎
@integza
5 жыл бұрын
@@humbertokokoa11 We will get there soon enough :D
@m.sierra5258
5 жыл бұрын
Hey! This only tests power for a specific rpm. What you really need to do is to change the clamp strength, and then graph torque vs rpm. Then plot Watts vs rpm, and you will see some kind of a bell curve. This way you not only get the maximum possible power output, but also the required rpm and torque to reach that value. This principle is quite intuitive when you give it some thought: The one extreme is no load and max rpm with, obviously, zero power output, and on the other hand is zero rpm with static torque and also no power output. Somewhere in between is the maximum power output, and I'm pretty sure it will be higher than what you measured in the video. Also ... keep making videos, I sense a glorious future for your channel!
@integza
5 жыл бұрын
You're 100 % right but I didn't want to overstretch or complicate the video... Thank you so much for the compliment :D
@SK-we1ty
5 жыл бұрын
@@integza is that mean if i plot Torque vs Speed curves with different value of friction for each curve (the value of friction is constant for each curve ), i will get the same result ? the second question: can i use weight scale instead of load cell and multiply the value with 9.81 to get the force value in Newton ? THANX
@integza
5 жыл бұрын
@@SK-we1ty Yes, you can use a scale. What controls the speed is the level of friction, so you can do it but is a little bit redundant .
@martinfyhn1976
4 жыл бұрын
Kudos on your videos 😊 I see this video is about a year old, and much has probably happened in that time, but I just wanted to give you a few tips about a couple of things: 1.: Dynamic torque: If you have the effeciency, the current, and the voltage of the generator, you should be able to calculate the output wattage, and the torque of the turbine. 2.: Soldering: Get a better soldering iron, clean the area (as little as a fingerprint can have a negative effect on the result) you are soldering and/or use flux (it will make a world of difference. The flux cleans the surfaces, and makes it easier for the solder to flow, and it makes the tip of the soldering iron last longer), solder at high temperatures (I find that 350C (48W soldering station) works for most normal PCB soldering (add flux, heat surfaces for a couple of seconds, add solder). I hate it, but leaded solder is the easiest solder to use. Unleaded solder will eat a low quality solder tip in no time, giving you an uneven surface, causing the solder to stick more to the tip, causing bad results - again; flux mitigates this, but a good soldering iron, with a good tip, will still make a big difference.
@GodGladiator1
3 жыл бұрын
The amount of work you put into these videos is great. I appreciate your humor while teaching me new things
@toxicgoldfish3482
3 жыл бұрын
This shows me how much the US education system has failed us because I just learned more in the past 16 minutes than I have in the past 2 years of highschool
@MrRyanroberson1
5 жыл бұрын
1:54 rewatching this, i think they still use levers. spoons are highly advanced fluid levers with fulcra near the user (usually on another finger)
@louisfranmahe5939
4 жыл бұрын
You did and error when you compute static torque: 11 N⋅mm → 11 N at 1 mm → 2.2 N at 5 mm → 220 g (and not 2 kg) at 5 mm
@integza
4 жыл бұрын
I know 😅
@CrackyCreates
4 жыл бұрын
Ah, a drinking game easy... *3 minutes passes* Petja GIVE ME THE OTHER BOX OF VODKA BLY- *youtube loads an m107 anti material rifle*
@integza
4 жыл бұрын
Ahahah, Don't tell anybody but O acidentally got drunk making this video 😂
@CrackyCreates
4 жыл бұрын
@@integza ehat 0? I am not dtink but tgat boxis empty
@yeet4924
4 жыл бұрын
eah...eh i meant blin....babooshka make great blin
@Tungstenio80
4 жыл бұрын
I'm was amazed when I saw the bottle of Beirão and realized you were actually portuguese. So proud And you make these videos so entertaining, you're quite the smartie :)
@paulbunyangonewild7596
4 жыл бұрын
Love that black and blue gingham
@giovannip3415
3 жыл бұрын
hahah si nu grand comba' stai fuori come un balcone!!! Watching your videos make me feel the stress of the competition in which I may graduate in electrotecnic a little less painful and anxiogenic!! Thank you!
@mattflynn8643
4 жыл бұрын
ahh my man. i thoroughly enjoyed this video. i learned a lot and your song is going platinum
@dentonfender6492
4 жыл бұрын
This guy is multi-talented. Good shows. Well so far I've only watched two of them. We all love Science, and Engineering, and then you present it so entertainingly. Maybe soon you could replace Bill Nye the Science guy. I think he makes a pretty good living down in LA presenting Science to Kids, and Adults.I like the hands on approach. It's cool!!!!!!!!!!1
@saxy1player
3 жыл бұрын
The curve at 4:18 actually shows your hammer as quite the average hammer :D
@mentalterbelakang
5 жыл бұрын
if you can add friction control (using solenoid or something to control or add the friction), basicly you made complete dynamometer (brake dyno)...
@integza
5 жыл бұрын
Sounds like an idea :D
@aaronbaxter9935
4 жыл бұрын
Maybe not a shot but a sip of beer every time you say torque is a lot more manageable........I speak from experience 😂😂
@MrWilliam932
5 жыл бұрын
Gosh I'm so glad I suscribed to your channel!, also, I counted 32 times the word "Torque", I would be very wasted If I drank alcohol
@integza
5 жыл бұрын
Are you a man or a rat ???? Just kidding. Thank you for subbing :D
@MrRyanroberson1
5 жыл бұрын
another english tip: newton milimeters, or milinewton meters, the -s always goes on the last unit in the numerator (for example, meters / second is correct, and meter/seconds is incorrect. newton meters is correct, newtons meter is not.), but good job on including the s!
@integza
5 жыл бұрын
Once more, thank you so much for the help! I'm trying to improve my English :D
@MrRyanroberson1
5 жыл бұрын
i must mention the distinctively beautiful sound of a spanish person pronouncing the Ls in words that end in -ld or -lt
@yassinelessawy6101
5 жыл бұрын
Thank you for that tip
@LanteanStargater
5 жыл бұрын
@@MrRyanroberson1 Portuguese
@MrRyanroberson1
5 жыл бұрын
@@LanteanStargater i should have known. i know a spanish guy and he pronounces 99% of all Ss as s, when about 50% of them are supposed to be z. integza pronounces the Ss much more accurately... or at least much more often z.
@0xXxSiFxXx0
2 жыл бұрын
science brilliance and comedy .. how can it be that u have only 500k subs?
@CrazyMadness23
10 ай бұрын
automaticly taking Nmm instead of mNm means, you understood math basics :D GJ!
@ejrambadt
5 жыл бұрын
I like when you make stuff. Makers make this channel
@epicab2456
4 жыл бұрын
THAT'S a nice EXCUSE to empty some bottles ..... OF MILK OFC!!!.
@ATLaboratory
5 жыл бұрын
I mean, great video is nothing compare to this!! Not only science and techinolgy!! Very very good :)
@integza
5 жыл бұрын
Thank you! Coming from you the compliment means a lot :D
@ATLaboratory
5 жыл бұрын
@@integza the compliment is necessary. You make video better than mine, more interactive and funny:) yes I also notice that the power of 38W is alittle bit to large haha;) it shoul burn the friction with the shaft..
@integza
5 жыл бұрын
@@ATLaboratory To many conversions and I messed it up XD
@ATLaboratory
5 жыл бұрын
@@integza haha it happens also to me to say something and let people see somenthing else in the video;) I just post a comment and I pin it at the top
@alleyse
5 жыл бұрын
Great production values and content, I'm sure more subscribers are on the way!
@integza
5 жыл бұрын
Thank you :D
@RetroKevin
3 жыл бұрын
Very smart guy. Most videos cover things I will never ever fully understand. Love every video I've seen so far. Soldering skills need some major improvements.
@samsimington5563
3 жыл бұрын
Ha! I knew you wouldn't be sober by the end of the video which by the way was very interesting
@oliverer3
5 жыл бұрын
I just love this channel more for every video.
@integza
5 жыл бұрын
And this channel loves you !
@oliverer3
5 жыл бұрын
@@integza The KZitem algorithm gave me something great for once!
@B33fSupreme
4 жыл бұрын
mayonnaise analogy was legit lol
@lexscarlet
4 жыл бұрын
I love the clearly uncomfortable conservation guard
@atiger4716
4 жыл бұрын
You are a such a talent man. You should have millions subscribers. Your content are incredible valuable and very entertaining Thank you very much!
@owaisfarooqui6485
5 жыл бұрын
This is one of my favourite channels
@integza
5 жыл бұрын
Thank you owais :D
@drumbass41
5 жыл бұрын
Once again, great content! to the moon and beyond dear Watson!
@integza
5 жыл бұрын
I just dropped a tear :D
@DIYTECHBROS
5 жыл бұрын
Really entertaining style of video! If I may give you one tip on your soldering? Use a smaller tip and 0.5mm solder. Then you can (1) maker sure the soldering tip is touching the pin and the pad, and (2) you can see the solder start by filling up the gap between the pin and the hole, before spreading on to the pad and up the pin :-) Also, use flux!
@integza
5 жыл бұрын
Thank you for the tips and compliments :D
@nicolasbroodryk3407
3 жыл бұрын
Super stoked that I found your channel. Keep it coming 😉⭐
@UmbraAtrox_
4 жыл бұрын
I'm 4 minutes in and might have alcohol poisoning. Great game. Thumbs up
@officialperu909
5 жыл бұрын
You are the new (drunken) tesla
@integza
5 жыл бұрын
Sound about right ahahah
@poland5606
4 жыл бұрын
Drunken FPS Russia
@gadgetbuster69
4 жыл бұрын
What you made is essentially a small scale dynamometer! Very cool, I could see RC car hobbyist wanting this very thing, just in a slightly different configuration. Love you channel,if there is anything I can do to help, just let me know!
@justahamsterthatcodes
4 жыл бұрын
I'm 16 and I have diabetes from all this chocolate milk! Thanks integza! Just kidding! I'm fine! Amazing videos btw! Keep up the good work!
@peerappel2012
5 жыл бұрын
I can't believe a video could make me laugh this much times! :-D I really like this clever idea! Soldering tip: Heat the whole pin + entire pad both as well as possible, then add solder, stop adding solder and remove the iron. If your joint doesn't turn out as you would've liked it, keep in mind that you need to fully heat the whole joint including solder again. So you can't simply scrape some excess solder off of your joint, because that will result in different layers in your joint which will fail much quicker. (And those fails are VERY shitty because they're really hard to find out about...) :-)
@integza
5 жыл бұрын
Thank you for that comment an tip Peer :D
@NeoCat80
5 жыл бұрын
Hmmm... 38watt you mean 3,8watt (3300rpm/60*2*pi*11Nmm/1000 ~ 3,8W), great video :)
@integza
5 жыл бұрын
You're right! I forgot the point and then messed the audio up too XD
@ckazruddy6796
4 жыл бұрын
@@integza 11g is .11N so power must be .38watt right?
@MrTomasMaliauka
4 жыл бұрын
Your videos are interesting AND FUNNY. New level in making science and technology closer to ordinary people. LIKE :)
@maikelwarmerdam8911
2 жыл бұрын
10:53 dude you klled me hahaha that was the lost one, i'm going to bed. 😂😂
@indiananimecreator8471
4 жыл бұрын
The most useful video of all time everyone should watch great job
@integza
4 жыл бұрын
Thank you ;D
@rikdenbreejen5230
4 жыл бұрын
Catchiest song in the world! Now i know what wires i need to use
@samsimington5563
3 жыл бұрын
I think your drinking game is weird and I can already tell that you'll be moderately drunk by the end of the video
@harryjohnson615
3 жыл бұрын
This guy has definite overtones of Borat about him 😁😁 Great video too.
@tamojitsaha1128
5 жыл бұрын
Your soldering skills is amazing!!! May God bless you son!
@shengluohuangxe8069
4 жыл бұрын
A drunken Tesla with anime artwork at the background...??? Got to see more of this channel... The Emperor might go funky to see this.... hoh hoh hoh..!
@crypsiee
4 жыл бұрын
Your work is awesome, it deserves much more appreciation. Very funny way to explain science at a high niveau. Even if its not much, i do some promotion for you when i meet my friends.
@akshatgupta35
3 жыл бұрын
Great video man 👍 But I still have a doubt on the load cell connections and the lever...like how to efficiently get the rotational force on the lever and to the load cell? Plz help
@SiR2Dean
3 жыл бұрын
A yr on and this video is still making me laugh! You're knowledge and teaching ability is second to none mate!
@serialxnet
5 жыл бұрын
DIY Powermeter is so cool! Insta-subbed. Keep up the good work!!
@integza
5 жыл бұрын
Thank you so much :D
@pradeeprajpoot4342
Жыл бұрын
my personal suggestion is that you should focus the camera more on the wire connection and working element rather than in the display screen. so that we can learn the concept and what is the exact location of sensors and load cell in the project.
@diederickb1806
5 жыл бұрын
Thanks so much for sharing your model! Awesome work getting this working.
@integza
5 жыл бұрын
Thank you for that comment :D
@PerryStevPT
4 жыл бұрын
Beirão was a really good choice, I recommend. I was about to say that tiny motor could never reach 38W of power! But you can still power LED's, listen to music, and charge your phone (just very slowly).
@ErikBongers
3 жыл бұрын
If I understand it correctly, the dynamic torque meter does the same as the static one, which weighs the hammer on the scale...except that the handle of the hammer slips. The higher you clamp down (less slippage, aka more brakeage), the slower the motor will go. And that's the relation you measure: rpm at a given brake force. The brake force is measured by putting the scale under the brake(aka the hammer) - just as with the static setup.
@LOVEisTHEultimateLAW
4 жыл бұрын
this is one of the best channel on youtube
@jeremiahevans2583
3 жыл бұрын
You have such amazing videos that get me inspired to design and create! Much appreciated buddy your doing the world alot of service. 😊
@nissanrb30
4 жыл бұрын
Very glad I found this channel. See what happens when you google Tesla coils after smoking?! Lol Great work!!
@LGFGAMEPLAYS
5 жыл бұрын
What a great channel I found! Thank you for doing this! Sorry by my English (Brazil)
@integza
5 жыл бұрын
Thank you :D Don't worry, I'm Portuguese, so I'm right there with you on english XD
@TheFantasticLoki
2 жыл бұрын
16 shots in under 4 minutes??? You tryin to kill us haha
@isaaclux2128
3 жыл бұрын
I got 2:43 in before surrendering. You win, now I got three more drinks to take... The rest of the video will be for enjoyment only.
@MrRyanroberson1
5 жыл бұрын
thinking about it even more, you have all the tools necessary to calculate the exact mass of an object using a kibble balance.
@0calvin
5 жыл бұрын
Back when I used to race R/C cars they sold dynos that consisted of a brushed electric motor running as a generator with it's output able to be run through various loads (resistances). So based on the current generated at each load and the respective RPMs at each load, the dyno could estimate the power. But how one goes about calibrating that business is another story.
@integza
5 жыл бұрын
Thank you for the input :D
@Eman6240
5 жыл бұрын
Love your delivery.
@integza
5 жыл бұрын
Thanks :D
@ejrambadt
5 жыл бұрын
I just found you today. I like your stuff. Keep it up.
@integza
5 жыл бұрын
Thank you :D
@FrankHertzschuch
5 жыл бұрын
Oh please make more of this "Tutorials" (I don't mean the drinking part) ;-) I like your channel!
@integza
5 жыл бұрын
Thank you :D
@vodu990
4 жыл бұрын
"If your under 18 it shoud be choclatemilk." *LAUGHS IN GERMAN*
@KlausJepps
4 жыл бұрын
Integza: Thorque. you know, because Thor has a hammer... Mjølner: I have a name already.
@tz10-z8g
5 жыл бұрын
Just discovered your channel, great job sir, keep it up! You just found a new subscriber :)
@integza
5 жыл бұрын
Thank you and welcome :D
@AlbertoM4A1
5 жыл бұрын
Man you are so fun!
@integza
5 жыл бұрын
Thanks :D
@cyn3rgy759
4 жыл бұрын
You are an excellent entertainer, sir.
@sergiomonteiro438
4 жыл бұрын
...E o que é que se bebe aqui?????? LICÔR BEIRÃO!!!!!!!!!!! Boas Festas e abraços Tugas!!!!!
@integza
4 жыл бұрын
Boas festas !
@BrunoSa96
4 жыл бұрын
Bem que eu suspeitei que era tuga
@rainerandkatieniederoest825
2 жыл бұрын
That song was very amusing! LOL
@NikKappa
5 жыл бұрын
Shouldn't you increase the friction untill it stops?
@integza
5 жыл бұрын
If I did that I would be measuring static torque :D
@NikKappa
5 жыл бұрын
@@integza well, a little earlier😂😂 Apart from everything I love your videos!
@SK-we1ty
5 жыл бұрын
@@integza so , how can i set the value of friction .... or it is just an arbitrary value????
@integza
5 жыл бұрын
@@SK-we1ty In theory you should measure torque in several levels of friction and plot a curve but because youre measuring torque and speed at the same time you can get what you want with the power equation.
Пікірлер: 648