What about the gearbox? 5L40 is able to accept 400nm. And it is the worst part of this car. At least, you should change the gearbix oil often.
@garage.86
7 ай бұрын
Look on my channel the next video about the Range Rover😂 actually the gearbox broke and now iam swapping to m57n2 and zf 6hp28
@albertgenzxhelili2097
9 ай бұрын
you dot talk abaut conection bituin turbo an intercoler.. how you manage that?
@marktipton218
Жыл бұрын
Well done bud keep it up and moor videos plz 👌👌👌🫣
@garage.86
Жыл бұрын
Thanks ! There will be a whole new video series soon where i swap the engine and put a zf 6speed in the l322 so stay tuned 😊
@outland4
Жыл бұрын
How did you Connect the compressed air side since There different? .you can also Change the intercooler to mantain the air coolder after the Higher compression
@garage.86
Жыл бұрын
I took the flansh from the e60 that bolts on the turbo cut the rubber hose of and put the original turbo hose on with a clamp, intercooler is on the to do list i need to upgade it cause now i bought a another map and rail pressure sensor to put even more power on the stock map sensor measures just to 2.5 bar absolut boost and rail sensor just 1500bar with current map iam running 2.45 bar absolut boost pressure with new sensor i aiming at around 2.7 - 2.8 bar then I definitely need a better intercooler idk if iam gonna make a video about this but if that would be a interesting video let me know :)
@outland4
9 ай бұрын
Send me.same photos of the turbo link do intercooler. I 'll try do do the same✌️ since you put a turbo upgrade on the BMW, thas that one fit the RR?
@georgeboy5511
11 ай бұрын
Do you know what model of 2260v you got? All the ones I’m looking at have an electronic actuator and I think they’re manual on these or can they be swapped over?
@garage.86
11 ай бұрын
U need one with vakum actuator and then u need u either build a new engine mount bracket or rotate the exhaust side of the turbo but then u need to adjust the actuator again which isnt quite easy i think early bmw e60 530d habe Vakuum Controled gt2260v
@kize32
Жыл бұрын
What is the fuel consumption after modification? How much do you pay for TUV+ insurance a year in Germany?
@garage.86
Жыл бұрын
fuel consumption is slightly more but i drive faster then before i pay around 600 euro a year for insurance and around 400 for tax
@kize32
Жыл бұрын
@@garage.86 nice.thanks
@outland4
9 ай бұрын
Uao.. in Portugal, till 2007 a td6 will pay 55€/year and about 180€/insurance
@joblogs542
Жыл бұрын
Done this 2years ago murder it was ha
@garage.86
Жыл бұрын
nice how it worked out for you ? did u had any problem with the gearbox?
@rider-hy9hn
Жыл бұрын
Da li je pouzdan? Da li se isplati? Da li je istina da dosta krcka unutra i da ime buke vetra? Da li je volan neprecizan? Unapred hvala na odgovoru. Lp
@garage.86
Жыл бұрын
onako, ako je dobro servisiran ovisi za sta ga koristis ako ti treba auto da vuces prikolicu onda je dobar krcka malo al ipak je star auto cuje se dosta vjetar kad ides 150 i vise je auto ipak ima skoro 3 tona nema na cemu
@emogirls80
Жыл бұрын
GT2260V
@garage.86
Жыл бұрын
Yes, Sir!
@jirivanecek7089
Жыл бұрын
Hello, what about gm gearbox is it run after adding more power?
@garage.86
Жыл бұрын
Actually the gearbox broke but not because of to much torque. The oil pump in the gearbox failed and the car does not stay in gear. But an update video for the range rover will come soon but it’s getting more power and and 6speed zf transmission :)
@jirivanecek7089
Жыл бұрын
@@garage.86 Thanks for update, maybe is easier to implant zf8hp ?
@garage.86
Жыл бұрын
@@jirivanecek7089 iam not sure if it is easier cause for 8hp u need can controller and standalone ecu and its very expensive i already got a donar car for the L322 so withhin the next 1-2 weeks there will be an update video on the Range Rover
@jurre007
Жыл бұрын
@@garage.86how is it going with this upgrade ?
@garage.86
Жыл бұрын
Well i was supposed to pull the engine out this weekend but my lift broke and now the car is stuck on the lift need to fix that hopefully ill get some work done till next weekend :)
@Rovercoupe.
Жыл бұрын
Very interesting..did you change exhast to make it fit and any pipe work..what else is needed.
@garage.86
Жыл бұрын
Thanks , no the exhaust bolted right on i just needed to rotate the turbo exhaust housing to clear on the engine mounts but otherwise it was plug and play also on the compressor side i needed to cut a bit of the charge pipes but it was very simple :)
Пікірлер: 30