Irish Saddler where did you order? I asked where to order but he didn’t answer my question.
@curtguru
4 жыл бұрын
@@paulcrave3112 it looks like he answered you two days ago....
@Prog27801
4 жыл бұрын
Pushing up daisies on FB. His name is Trevor Byrd. Message him there and he will need either Paypal or Vemo.
@Prog27801
4 жыл бұрын
Try this www.paypal.com/paypalme2/TrevorByrd
@paulcrave3112
4 жыл бұрын
TradLife Films yeah, my bad. I found that now.
@curtguru
4 жыл бұрын
Well done!
@nicod1886
4 жыл бұрын
I did mine very similar however chose to use a locked brummel continuous loop. The method in the video should be okay but since the loop is for life support, I went with a locked brummel.
@nicod1886
4 жыл бұрын
Awesome video 👍
@jasonphillips1342
4 жыл бұрын
Why not just get a longer piece of wire and start at the end and pull it all the way through at once
@paulcrave3112
3 жыл бұрын
What kind of knot do you use on the bridge for as stopper knot?
@bowhuntingforlife
4 жыл бұрын
When burying the tail the length of the the spliced side going in like 3 or so short pulls through are you putting the rope right back in where you left off or just going back into the rope as close as you can?
@pushingupdaisies8196
4 жыл бұрын
Pull it back through the hole it came out,
@outdoors-fun
3 жыл бұрын
Is that 1/8 or 3/16? I know you said 1/8 at the start but that looks thicker?
@tylerelkins9619
22 күн бұрын
I thought he said 1/4
@NorthernMIPathfinder
10 ай бұрын
Do you sell these kits "ready to use"? Meaning the continuous loop already done and a loop on one end already in place? How much & do you still sell these, I see that this video is 3 years old already...
@MTNMANWOODWRKS
2 жыл бұрын
I’m having a lot of issues doing the full bury. How did you feed it all the way through? I can’t get it do go into itself after doing the first loop
@ashtanga2000
4 жыл бұрын
Can you add this to an intact Mantis and basically use that Mantis bridge as a back up and limiting the adjustability of this utilibridge?
@Prog27801
4 жыл бұрын
AshtangaBoy that’s what I plan on doing until I trust my handy work
@Prog27801
4 жыл бұрын
That’s what I plan on doing until I trust my handy work
@paulcrave3112
4 жыл бұрын
Nice.
@paulcrave3112
4 жыл бұрын
Do you tie a stopper knot on the utilibridge?
@Prog27801
4 жыл бұрын
Definitely tie a stopper!!
@dajahvue
4 жыл бұрын
Can you make the cruzr bridge style?
@bryanc5540
4 жыл бұрын
On the website, is this listed as the “36” 1/4” Adjustable Whoopie Sling Bridge”?
@danalarson6586
4 жыл бұрын
DIY Bridge
@Lt.Dan2.0
4 жыл бұрын
Just a question is it necessary to feed that much back into itself? Or could you get away with 8in or so?
@Dcptcn643
3 жыл бұрын
on Tethrd's, it's completely buried. They say it's necessary for the prusik to catch properly.
@sheldor5312
4 жыл бұрын
Still sell the kits? Didn’t see it on website
@paulcrave3112
4 жыл бұрын
No link to where to order?
@pushingupdaisies8196
4 жыл бұрын
Please visit my facebook page to order m.facebook.com/pushingupdaisystrevorbyrd/
@joesoupcoxman
4 жыл бұрын
How do you tie a safe stopper knot?
@NorthernMNbeard
4 жыл бұрын
joequepublic it’s just a square knot. You can tie a fancy fisherman’s knot. But even in the fire service a stopper knot is just a square knot
@johnchandler5689
4 жыл бұрын
So I had some 1/4 amsteel laying around when I seen this and I'm having rope slip on my continuous loop. Is this bc if the bigger rope? Should I buy 1/8 or is it something I did when I made it? Thanks btw awesome vid
@joesoupcoxman
4 жыл бұрын
John Chandler the Prussic loop must be a smaller diameter than your bridge line
@johnchandler5689
4 жыл бұрын
Yeah I found that out and ordered 1/8 diameter thanks for the reply
@virginiahunter3264
4 жыл бұрын
What size amsteel is the prussic?
@NorthernMNbeard
4 жыл бұрын
Jason Falbe I thought he said 1/8”
@nitlions8
4 жыл бұрын
I'd love to order one, as well as another item or 2, from you. I do not have Facebook, how can I order? Thanks
@pushingupdaisies8196
4 жыл бұрын
Please visit my website www.customamsteelproducts.com
@nitlions8
4 жыл бұрын
Looked for and then performed a search for "Utilibridge" on your webpage, with no results returned. Do you call this something else? Otherwise, can we communicate directly? Again, I have no FB.
Пікірлер: 49