Could P0015 error code be related to this issue by any chance? I have a weird “gravel in a tin can” noise coming from the engine around 1500-2000 rpms I searched around everywhere and couldn’t find it only possible things I saw were the vanos solenoid or the timing chain tensioner?
@cctvace
6 ай бұрын
This proved to be very helpful thanks for sharing, made my attempt at doing this easier than I’d built it up to be 👏👏
@usmansaeed08
7 ай бұрын
I have the same error code on F20, but the engine is B38. The code comes and goes by itself. There are no other problems, nothing like high consumption or even limp mode, the car runs fine with the light on as well. Can you please guide on where the solenoids are in B38? How can I change them? I also checked the camschaft position sensors, but I am not sure what voltage should they show, do you have any information on that?
@Denime
4 ай бұрын
What did you use to get the T30 bolt out on the exhaust side please? I'm struggling to find a combination of attachments to get in there and provide enough purchase to undo it. Might have to take the turbo off at this rate! Edit: thanks for the video by the way, was very helpful!
@mattwillow7
4 ай бұрын
Just a 1/4 ratchet and extentions, we managed to get a combo on which is just few mm away from the turbo, undo the bolt and then once it starts goingremove it rest of the way by hand and only the t30 bit. That's if I remember corectly, it's been a while since then 😅
@Denime
4 ай бұрын
@@mattwillow7 thanks for the reply. I managed to snap a T30 insert going in at an awkward angle so I'm trying to bodge something better together. They really didn't design this to be easily removed 🤪
@nebulosza8682
7 ай бұрын
Is it possible for the solenoid valves to be faulty without producing vanos error codes? My 116i feels like it's misfiring when under higher acceleration and really lacks power when cold, feels like a long delay for it to start revving up. I've ruled out coils and plugs, I know it's not that. Car is at about 75k m / 120k km and has not had any vanos maintenance done before. I'm thinking of getting a couple of new solenoids and putting them in myself before I sell it.
@majed888
6 ай бұрын
I’ve had similar issues with mine, my injectors after 1 year started failing expensive repair but now all good
@zp0g59
9 ай бұрын
Did yours have codes 130204 and 130304? I keep getting this stupid limp mode, but it only happens when I change into sport modes but the car is completely fine
@mattwillow7
9 ай бұрын
Not sure I had both, but did have 130308 and one more. Either way, if I'm not mistaking 130304 should be camshaft stuck, which usually is VANOS selenoid related.
@kevinaquarius6011
21 күн бұрын
Thsnk you, educational and funny :) thank you
@betounivazo3452
6 ай бұрын
Hi bro, I have a 2014 BMW 114i. It has unstable engine speed and a little lack of power. I changed filters, oil, spark plugs, coils, injectors, and finally the 2 oxygen sensors. and just now I get error 130204. Do you think the problem of unstable engine speed and lack of power is due to VANOS? please help me a lot
@mattwillow7
6 ай бұрын
Could be, but the question is why do you have VANOS fault, maybe it's just the selenoid like in my case, but since you have additional simptomes it could also mean that the timming is a bit of
@betounivazo3452
5 ай бұрын
Hello friend, I already solved my vibration problem, it was just an air vacuum.... but I still had several errors of the VANOS. I drive and I get "propulsion fault" and the turbo stops working then I turn it off and wait about 30 minutes and the problem goes away. every day 130004, 12048, 12AF08, 12A308 what do you recommmend me to do ? change the 2 openings? or only 1? the wiring? I would greatly appreciate an answer, thank you
@sifisokhumalo9751
3 ай бұрын
I didn't hear you properly. You said w3 must not foot to reset our elevations or something like that
@Thomas-t9s5y
7 ай бұрын
I’m about to change this solenoid due to rough idle when cold only. I test the pcv and works fine. Did you have problem on cold start idle with this ?
@mattwillow7
7 ай бұрын
Nope, it ran and drove great, just turned on the fault every now and then. Turn it off and on and it would be god for few houndred km untill it did the same again. Funny thing is I had this happen on 4 out of 4 N13 powered BMWs I had. Even funnier thing is that last two did it every day 1-2 km after first start, restart it and you could drive it trouble free that day no matter how many km or how many drives you did. Untill next day that is, than after 1-2 km it would come on again 🤣
@ioyonutz94
3 ай бұрын
hei did you solve the problem? my car make the same sound on cold.. at start and at 1500-2000 rpm.. only for 10 minutes after start.. then is perfectly normal
@AshleyJohnson-j2hno
3 күн бұрын
Does it have to be reset on a BMW computer after fitted?
@mattwillow7
3 күн бұрын
If you want to do it properly, yes, VANOS adaptations need to be reset
@AshleyJohnson-j2hno
3 күн бұрын
What happens if it’s not reset straight away ? Will it just show a light on the dash until it’s reset
@mattwillow7
3 күн бұрын
@@AshleyJohnson-j2hno depends on which codes are active, but even if it does go off it will probably turn it on every now and then
@AshleyJohnson-j2hno
3 күн бұрын
@@mattwillow7 thanks for your help buddy 🙏
@naspinnn
5 ай бұрын
Hey :) can i clean this solenoid ? Brake cleaner or something ? I have a 130204 fault :/
@mattwillow7
5 ай бұрын
You can try, I used brake cleaner, sometimes it helps, but not always.
@naspinnn
5 ай бұрын
@@mattwillow7 when i buy new :D thanks
@shevblakeway2910
6 ай бұрын
HI do you have a vidio showing removal of the vanous sensor on driver side
@mattwillow7
6 ай бұрын
No, but I will make one in next few days, I have an F21 with intermitant intake cam fault su...
@anthonycampbell9807
6 ай бұрын
Did you not change the solenoid on the other side that’s real hard to get to
@mattwillow7
6 ай бұрын
No, on this car it was fine
@qmohammed4161
Жыл бұрын
Hi was your car shaking with engine light on?
@mattwillow7
Жыл бұрын
Nope, just got a random check engine light now and then, it would go off after turning the car off and back on
@jaredcourt4791
10 ай бұрын
What do you mean by reset the adaptation
@jaybo95
10 ай бұрын
Hi what do you mean by reset adaptations ?
@mattwillow7
10 ай бұрын
DME "learns" some parameters while you drive, you need to reset these for VANOS with diagnostic tool like ISTA so it can "relearn" these values
@hakzb1691
8 ай бұрын
@@mattwillow7 you mean clear codes once new one fitted?
@ameerk765
8 ай бұрын
What size is the engine is it 1.6 ?
@mattwillow7
8 ай бұрын
Yup, 1.6, N13B16 to be exact
@SpartaThe1st
Ай бұрын
Have a spare engine 😂 I died!
@mattwillow7
Ай бұрын
Well I had 7 of these N13 cars ( ok, one was a Citroen THP ), only one car was trouble free engine wise. We had 5 with VANOS fault, 3 with high oil consumption, 2 blown cylinders, 1 headgasket/carbonisation, 2 timing chains, 1 oil pumo chain... Yeah, it's a good idea to have a spare engine if you want to daily drive them 😅
Пікірлер: 43