FANTASTIC video. I lost my Phantom 1 which my techno-geek set up for me. I felt confident in setting up my new Phantom 2 - my geek moved away . . . This is EXACTLY the video I needed. First, I'll need to order the Futaba receiver that is still in my lost Phantom 1 . . . little did I know!!!
@lxprecords
10 жыл бұрын
Thank you soo much for walking me through this. It would have been a lot harder for me to figure it out on my own. Great video!!!!
@TopFPV
8 жыл бұрын
Thank you! Amazing and detailed explanation, programmed Naza v2 with Futaba 18SG using your guide as settings/menu are exactly the same.
@athertop
10 жыл бұрын
Best explanation I have seen to date. Great job! You didn't mention out of range fail-safe configuration though (as mentioned in other comments) this would be helpful. Thanks again
@HansOlofViktor
10 жыл бұрын
Thanks. Very helpfull for setup of GPS and Failsafe switch. I have the Futaba 14SG and DJI A2 system.
@madmax85
10 жыл бұрын
Thank you for this video! I will try this tomorrow on my phantom vision, I think is all the same!
@Flyboy24
2 жыл бұрын
Love your work mate!
@JulianLiebl
10 жыл бұрын
Great Video with detailed explanations! Thank you!
@txworshipleader
9 жыл бұрын
Thanks for the walk-through -- very helpful! I'm wondering if there might be a way to use the dual-rate (or another) function to use the momentary SH switch on the controller as a "start-up" switch (i.e., set 2, 3 & 4 to +100, and set 1 to -100). How difficult is this to accomplish, or is it possible at all? Could it also be programmed with a delay to prevent an inadvertent, in-flight shut-down? Thanks!
@RuneVenes
10 жыл бұрын
Great video, but you forgot the fail-safe function if your copter looses range with your Futaba... What happens if you turn of your Futaba for example (simulate loss of signal)
@drummerdonniedotcom
10 жыл бұрын
Failsafe or "Return to Home" kicks in just like with the OEM transmitter.
@UloPe
10 жыл бұрын
The antennas should be positioned in a 90° angle to each other.
@johnmeyer3333
9 жыл бұрын
Great video, very informative. I have a DJI F450 Flamewheel, NAZA System, Futaba T8FG Super with and Futaba R6208SB (SBus) receiver. I am trying to find out how to connect the two landing gear servos and how to setup the switches on the remote. Do I just connect the servos with a supplied Y Cable to the receiver channel one? I am a novice here so learning as I go along and watch KZitem info like yours. But I am stuck here and before making any mistakes thought to drop u a line first. Any input is appreciated. Thanks from down-under.
@clearlyfromabove6123
10 жыл бұрын
In order to have a quad copter initially be able to move very slowly right or left, while in a stationary position, is it possible to have the stick sensitivity minimized? This would have (stationary) left/right quad copter movement start off very slow and that's what I'm looking for. Any thoughts? I have the Futaba T8FGS transmitter from DSLRPros.
@chriswebber943
9 жыл бұрын
Super cool vid and info. I have a Q? Trying to sort out my end point on the throttle - When I bring my throttle back the Motors cut out and I don't want them to. I'd like to bring it back and just have them on tic over until I switch off - Can you point me in the right direction? Thanks
@MRG_88
10 жыл бұрын
Haven't seen entire video yet.....do you show self centering throttle kit install for the sg14?
@irfanpin-2255
5 жыл бұрын
Hey bro I can use fly sky receiver with 10ch.S bus signal to the controller????
@VideoAtlantaLLC
10 жыл бұрын
A ot of work, nice job, thank you.
@LongPham-xi7lj
10 жыл бұрын
Chào Anh, Congrats on your video.. it is beautiful!
@darrensusin8903
9 жыл бұрын
Do you have any videos about using the S1000 with the 14SG? I can't seem to find anything online.
@ianobre
9 жыл бұрын
You dont use hover lock? (throttle on 50% locked). Can help with this?
@Hoverbot1TV
9 жыл бұрын
I get 3km on a Frysky 9x and patch and my fg14 and 8 stoc should do at min. 3km-5
@djonegloveTV
10 жыл бұрын
Thanks for amazing video...
@dangerousdoug6017
10 жыл бұрын
Very good video. How do you program a gimbal in the 14GS?
@shanec4441
7 жыл бұрын
For the best transmission from the receiver, the receiver antennas should be separated in a y direction - not tapped together as you show
@cybertec0285
10 жыл бұрын
the diversity antenna on your Rx, shouldn't it be positioned in 90' from each other to obtain maximum signal in any position your aircraft maybe.
@madmax85
10 жыл бұрын
Therefore, the video tx is also 2,4ghz
@MrWhat8ver
10 жыл бұрын
thanks mate, thats really help
@MMTera9
10 жыл бұрын
Hi ;) so same setup on your video ,should works on Phantom 2 ?
@ohaleceiffel
10 жыл бұрын
does this programming apply to the Futaba 14SG?
@evilmuscle
10 жыл бұрын
Do you have any videos programming the futaba t6j to a dji f450 ?
@mayantribe
9 жыл бұрын
Let me know if u ever find one please
@dansauerwald4220
10 жыл бұрын
Will those settings work for the Discovery Pro?
@chriswebber943
10 жыл бұрын
Good stuff!
@JLXPRO
10 жыл бұрын
The radio antennas.... not correct. one 90 degrees from the other.
@aerialphoto
10 жыл бұрын
wait I get a solid 1km with my stock phantom 2 transmitter thats 0.6 miles. this only tops at 3/4 (.75 miles)?
@saltire546
10 жыл бұрын
Very true waste of money buying the Futaba
@airborne101st45
10 жыл бұрын
I think the Phantom 2 has more range than the Phantom 1 though.
@aerialphoto
10 жыл бұрын
Yes my record with the phantom two stick remote has been 1400meters.
@dmitrid7966
10 жыл бұрын
Futaba 8FS FASST is rated for 2.5 miles or 4k... Google is is your friend, cure your ignorance. My record is 7km.
@aerialphoto
10 жыл бұрын
Sweet. And where can I read more about the range of the futuba remotes?
@coreyperez13
10 жыл бұрын
Brian, Great video! It helped me with my 14SG and Naza M-V2. I too would recommend a follow up on the TX/RX Failsafe programming/function. I looked through and through the manual with no luck and finally found a link on < www.rcgroups.com/forums/showthread.php?t=1973186 > (look for LNK > FAILSAFE (PG1) :) about halfway down under the group of red text. The video got me 95% of the way done, this link finished up the failsafe. Excellent video, great audio, I'd only have recommended more clarification/better views of the remote, possibly a 2nd camera? I love that you had a screen recorder as well. Thanks again Brian, you got me through a 9XR to 14SG swap with very little (work) on my end! Thanks, Corey
@jamesamuta
10 жыл бұрын
please, for the benefit of new users, explain the fail-safe function
@guytupinier1651
10 жыл бұрын
cette radio est une grosse merde !
@TheMfbs17
10 жыл бұрын
You forgot to add failsafe when you turn of yor Tx.
Пікірлер: 46