Looks and sounds like an AWESOME engine for this plane! (I own two of them). Just watched your flight video - beautiful! Looks FAST, TOO! Nice job.
@robarnold23
8 жыл бұрын
Really clean install. Nice craftsmanship!
@knockoffs
8 жыл бұрын
+fdsa Thanks for the nice comment.
@MasboyRC
4 жыл бұрын
Awesome, it's looks like a real airplane.
@knockoffs
13 жыл бұрын
@Rica1556 No special conversion, Use the tank that came with the model and change the fuel stopper to a Durbro gas stopper (red) and change all the fuel line to tygon gas line. also i would put fuel barbs on the tubing for extra protection and fuel line clips over the barbs to keep line from walking off !!!. Good Luck with your P51 should fly great !!!
@knockoffs
14 жыл бұрын
@irshaad57 Yes, but you have to cut the rail mount down to fit. Back slide rails all get cut out and the carb will now fit.
@knockoffs
14 жыл бұрын
@microdon2 The included motor mount works just fine, Use your cut off wheel from your dremel and a sanding disc, and take your time fitting the motor. Lock tite the shit out of it when all done, i check my mount every ten flights and it has been just fine. check out my new build pics of my top flight P51 1/7th scale. It shows the cut off areas and the angles you need on the rails. Also keep the filler end from the slide rail that you cut off, You will need it for a spacer to keep the rails level
@knockoffs
13 жыл бұрын
@afjets20 Yes still using Xoar 15x8 prop. Works just fine. and the ignition pack that im using is a life pack by hobbico 2100mah. I get about 6 ten min flights with plenty of room left for safety.
@jorgenelsonfelix52
6 жыл бұрын
Espectacular Un gran saludo para todos desde Buenos Aires
@knockoffs
14 жыл бұрын
@EvvyThomas Maiden was a couple of days ago, And what a thrill ride it was. The plane only calls for a top engine of a 91 !!! This DLE 20 is 120 size in nitro. The high speed passes were outstanding, and the vertical is nuts !!!. I have a 16oz tank in it and can fly for 15 min and still come down with more then half full. Beef up the fire wall with epoxy and cross screws around the box, and your good to go. i Should have a video up soon.
@knockoffs
14 жыл бұрын
@EvvyThomas First prop that i had on the plane, was a Xoar 16X6, and i had to pull it off real fast. Was not a good match for this plane. At 1/4 throttle it would yank the plane off the runway. Good size i guess for a heavy warbird or a three d type plane. I myself like long and real looking rollouts and landings, Just like planes are supposed to look !!!
@stanjohnsuab
7 жыл бұрын
very smooth one turn start 👍
@knockoffs
14 жыл бұрын
@domingomartinezt i used the spinner that came with the model. works great with most props.
@TinkerManRC
12 жыл бұрын
Awesome stuff Great video..Tim
@knockoffs
14 жыл бұрын
@microdon2 thanks for the comment, And it is fast. Will have a speed reading real soon !!!
@stan230
13 жыл бұрын
Great looking Revolver :) Nice Job!!! Is the DLE20 hard to tune? Once again keep the videos coming nice work 10/10 for your videos :)
@kallitexniss
4 жыл бұрын
Do you use two servo for each elevator servo or one servo for both?
@knockoffs
13 жыл бұрын
@stan230 I used life packs, A123 batteries by hobbico, 3200 mah for receiver and 2100 mah for ignition. More information on my flite video on my channel. Thanks and good luck with yours
@TinkerManRC
12 жыл бұрын
Great video and Thumbs Up..Tim
@AphexTwinII
4 жыл бұрын
Too bad this plane was discontinued.
@domingomartinezt
14 жыл бұрын
What spiner your use? what size and brand? they sound is great
@matthewbailey3833
5 жыл бұрын
Cyclonic
@stan230
13 жыл бұрын
Hi I'm going to buy one with your exact setup it looks great, may I ask what battery did you use Li-po or Ni-Mah? Nice work 10/10 :)
@gertnood
8 жыл бұрын
If this was a 3D model, the static thrust would be meaningful. Seems to me the 6" pitch is robbing a lot of top speed with a
@knockoffs
13 жыл бұрын
@pitikbulag123 I used the large Tygon line, Not the extra large, Yes 6X3 O.D.
@vincenciussyp2696
2 жыл бұрын
what will happen if we use larger proppeler ?
@knockoffs
14 жыл бұрын
@DeadlyDon will take a reading soon and post results
@knockoffs
13 жыл бұрын
@pitikbulag123 Will check and post next time i take it out, Keep in mind that needle setting will change depending upon where you are located !!! (climate, Elevation etc, etc)
@knockoffs
14 жыл бұрын
@3gulfstream3 Thanks
@afjets20
13 жыл бұрын
@knockoffs Building a R70 with DLE20 and this was a big help. Figured I would have to cut the mounts and this certainly confirms it. Wondering if you know how many mah's the ignition is using during an average flight. Also are you still flying it with the 15x8 prop as stated in your flight video?
@microdon2
14 жыл бұрын
Knockoffs - so you use the stock engine rails and cut out the middle slide-into-each-other section? But then the two sides don't reinforce each other, right? And they're still strong enough? Also, I didn't see a fuel port on the cowl. Do you add fuel through a loose hose? Thanks - and great work. (I have my DLE 20cc on order!).
@knockoffs
14 жыл бұрын
@EvvyThomas valleyview rc Tell them Matt from New York sent you !!!
@knockoffs
13 жыл бұрын
@tubsucks just go on my youtube channel , look for DLE 20cc and Revolver 70
@AustinPetDetective
5 жыл бұрын
Is that a Xoar Carbon prop ?.
@knockoffs
5 жыл бұрын
Wood prop
@Rica1556
13 жыл бұрын
Knockoffs - Did you use any gas conversion kit or a special tank for gasoline. Im also buying a DLE20 for my Topflite p51 Mustang. Thanks.
@noshil
14 жыл бұрын
Did you use the stock engine mount and position on the firewall please?
@Phoverlander
13 жыл бұрын
@knockoffs can you share your needle settings on this, for my reference. thanks.
@tubsucks
13 жыл бұрын
Any flight vids mate?
@Phoverlander
13 жыл бұрын
@knockoffs is that 6x3mm tygon you're using or 5x2.5? thanks.
@TejasRCpilot
13 жыл бұрын
try a 14x10 for ultimate speed
@adrianquirino
12 жыл бұрын
when i find this propo 16x6 by xoar??? not carbon? is a nylon prop? thanks
@alexandernovara895
11 жыл бұрын
Saludos knockoffs.. Te escribo de Barinas - Venezuela.. Cuando graduaste el carburador cuantas vueltas le diste a la aguja de alta y la aguja de baja.. Yo tengo un revolver igual al tuyo con un 20cc y hélice 16x6. Quiero ponerlo en ese mismo tono.. Por favor respóndeme por este medio o a mi correo novaraf@gmail.com.. Estaré muy agradecido por tu ayuda..
Пікірлер: 44