I will show you how to make a gate from corrugated sheets with your own hands. The gate is swinging, with a separate wicket and forged metal elements. How to make a gate from corrugated sheets:
Stage 1 - draw a drawing of the future gate. The drawing shows:
- overall dimensions of the frame (frame), taking into account the thickness of the profile pipes;
- reinforcing crossbars inside the frame, ensuring structural rigidity;
- for built-in and separate gates - installation location.
- frames for viewing windows, video cameras and others.
- places of insertion (fastening) of locks, hinges, fastening of roller bearings, handles and other elements;
- installation locations for restraints and latches.
Based on the drawing, we calculate the necessary pipes, profile sheets, and screws.
Stage 2 - installation of supports:
- we drill holes in the places where the supports are installed to a depth of 0.7-1.2 meters. For gates up to 2 meters high, 1 meter of depth is sufficient. Gates with a height of more than 2.5 meters require a reinforced structure of supports with a foundation;
- we install supports from a profile pipe 80*80 millimeters into the holes, having previously welded the restrictive heels. We recommend covering the edges of the pit with roofing felt or plastic film to prevent the soil from mixing with the cement mortar.
- fill the pillars with concrete mortar grade M-300;
- we install the gate no earlier than 7 days from the date of installation.
Stage 3 - installation of the gate frame:
- the frame is made from a profiled pipe measuring 40*20 millimeters with a wall thickness of 2 millimeters;
- we weld the horizontal and vertical profiles of the gate frame to the post-mounted metal profiles;
- We weld the pipes together strictly at right angles (we use a protractor or a measuring metal angle). The distortion of the frame will subsequently negatively affect the closing of the gate, installation of profiled sheets and locks. We correct an incorrectly manufactured frame using hinges and adjusting the cladding;
- between the gate and wicket frame elements welds vertical profile pipes 17*17 millimeters with a pitch equal to the pitch of the metal profile;
- We weld metal hinges for fixing gate leaves and wickets;
- we weld forged metal elements onto the front part of the gate frame;
- we cut the welded temporary clamps of the gates and gates together;
- paint the gate frame and wait for the paint to dry completely.
Stage 4 - installation of profiled sheets:
- corrugated sheeting is pre-cut. We cut the material with a grinding machine, on which we install a cutting wheel or use an electric jigsaw with a metal saw. We cut the sheet for installation inside the frame 2-3 mm smaller than the internal perimeter. Then we cut out the places where we will screw hinges, locks, support posts, etc.
- we mount the profiled sheet onto the installed frame using screws. We screw the screws into the bottom wave of the profiled sheet. We install the screws through one wave.
We overlap the corrugated sheets together. We fasten the joints with rivets. The strip covering the gap between the sashes is welded.
Stage 5 - installing the lock:
- mark the place where the lock is inserted on the gate frame.
▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰
Sections (chapters):
0:00 Introduction
0:25 Dismantling old gates and wickets
1:15 Installation of gate support posts
5:15 Installation of gate sheathing
15:36 Gate bolt
17:19 Installation of wicket sheathing
19:08 Installation of gate and wicket canopies
20:13 Installation of shutter strips on gates and wickets
21:03 Installing a latch on the gate
22:50 Installation of lower gate stops
24:27 Installation of forged elements on gates
25:50 Painting the gate frame
26:50 Installation of corrugated sheeting on the gate frame
29:28 Installing a lock on the gate
36:08 Painting forged gates and gates
36:36 Conclusion
▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰
And in this video I will show you how to make a carport with your own hands • Навес для машины своим...
▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰
Subscribe to our channel and watch a video on this topic #gates, #doityourselfgates, #gatesmadeofcorrugatedsheets, #metalgates, #howtomakeagate, #swinggates, #wicket, #corrugatedsheets, #fencesofcorrugatedsheets.
▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰
Our social media channel following the links:
Facebook - / 1147375328749226
Instagram - instagram.com/delo__maste...
Telegram - t.me/delo_mastera_boitsa
Odnoklassniki - ok.ru/delomasteraboitsa
VKontakte - vk.com/club141674316
▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰▰
Become a channel sponsor and you will get access to exclusive bonuses. More details:
/ @delo_mastera_boitsa
Thank you very much for your support friends 💕
To develop the channel www.privat24.ua/send/1mdwa
Негізгі бет Тәжірибелік нұсқаулар және стиль Do-it-yourself gates made of corrugated sheets
Пікірлер: 113