Nice vid. Couple three comments. 1. Yes, its a "parking brake" perhaps at one time it was an emergency brake. Kinda like Guard Rails are now "guide rails". 2. The 4 threaded holes you had the good fortune to use to drive the rotor off with are actually there for the wheel speed sensor tone ring on DRW trucks. Your brass hammer is a bit small to pull rotors. 3. Before removing a rotor you should back off the adjuster on the emergency brakes (lol). Ask me how I know. 4. Extra: If the caliper needs to be replaced you can put in pads etc on the bench then just 2 bolts under the truck.
@clausineymarcos1769
4 күн бұрын
Thank you very much, the video helped me a lot. Now I can change without any problem
@st3v3harman
4 ай бұрын
This was a very helpful video. Prior to watching, I didn't really understand the tensioner. Thanks for the video!
@philipunderwood477
2 жыл бұрын
Awesome video. Thanks for great description and commentary. I hope to knock this out later this morning in 15 minutes also!!
@harleydriverpdtnm3996
14 күн бұрын
Very informative and great explanation Thanks
@haleybowling694
Жыл бұрын
Thank you for your video. It really helped me when I had to change my rotors and pads. I had no idea what I was doing and this is very informative. definitely helped me, especially with getting the rotor off.
@KendorFarms
Жыл бұрын
That's great! Glad it helped you out
@gumps1986
2 ай бұрын
Came to see how you put the heavy yellow spring on. Denied… I wound up putting it on first, using a pry bar to get both shoes in place, then putting the small spring in the opposite side. First side took me 40 minutes, second side took 5. A c-clamp holding the shoes from moving while getting the pin clips on helped a lot.
@keving4081
Жыл бұрын
I had a hell of a time reinstalling the clips on a 1500......then I saw your technique. 1500 seems to be a bit tighter regarding access. Thanks for the help.
@mikeries8549
9 ай бұрын
It's way tighter on a 1500 and costs less too. 😂
@houseofhug
2 жыл бұрын
Great video! Helped me a ton.
@JasonCarmichael
Жыл бұрын
Thanks for the video. If you think of the "parking brakes" and not "emergency brakes" you will probably use them all the time. 315k on mine, they are just not very tight anymore. A great time to check the wheel studs for replacement.
@williamfabiano543
Жыл бұрын
Great video, great job!👍
@that1fiddy_916
2 жыл бұрын
Awesome video 👍
@TroubleBKC
Жыл бұрын
My rig likes to stick in P, especially when it's cold. So when I park the old girl I shift the auto into neutral set the parking brake then back into P.
@Zidhfftffh
Жыл бұрын
you're a rock star. Thanks for the vid.
@KendorFarms
Жыл бұрын
Glad to help
@237130
3 жыл бұрын
Thanks for taking the time to walk through this. My parking brakes used to stick, now they don’t work at all. So who knows atrocities await me when I pull the drums!!
@237130
3 жыл бұрын
Also, what did the parts run you so I know what I’m in for?
@KendorFarms
3 жыл бұрын
With shipping at $150, I was 380 total. Locally it was over $800
@237130
3 жыл бұрын
@@KendorFarms Yikes, thanks.
@mikeries8549
9 ай бұрын
Do not be afraid of this job. On mine it was easiest to just break the springs off. If they don't break they pop out so try to break them. 😅 It's rusty as heck but just pretend it's not there. 😂
@jakebpau2396
Жыл бұрын
Great video! Thanks!😊
@glennbeadshaw727
Жыл бұрын
Awesome video thanks man
@Meal_Team6
10 ай бұрын
Good video, I had 08 ram 2500 diesel, and mine did not have the bolt holes for removing the rotor, I was able to ping the rotor with my air hammer and then use a dead blow and pop the rotor off.
@DinDooIt
10 ай бұрын
Same here, it wouldn't budge with just a sledge, I needed that air hammer for sure.
@keithbeaudoin4549
18 күн бұрын
Would have ben nice to see top spring going in!!
@everforexcanada5663
Жыл бұрын
great vid! can you share what's the white grease, the red paste and anti seize's names and/ model? thanks! newbie trying to learn
@chrissnoett3060
2 жыл бұрын
Great video! The rear seals started leaking on my 15 3500 and took out my parking brakes. I put my truck in neutral then set the parking before putting it in park, I know it's a sickness... I forget what my jack stands cost but it has nothing to do with the price of the truck. Hydraulics fail, it's just a matter of when.
@DinDooIt
10 ай бұрын
I live on a mountain and I do the same thing, there's less stress on the parking pawl that way.
@savage22bolt32
2 жыл бұрын
Thanks for posting this, I needed a refresher course. FWIW, It's Nov-2021 & I'm just slapping a set of pads on the back of my '02 Ram 2500. On my truck, both of the caliper bolts have 13 mm heads. I bought the cheapest pads they had in stock; $27.50 + state sales tax. Parking brake? What's a parking brake? lol
@utubota5522
5 ай бұрын
Very helpful, thanks
@angie19712
Жыл бұрын
ohhhh btw... great video. you rock. like a star ]
@rayb.6418
2 жыл бұрын
Very helpfull boss thanks
@victorbunch1442
2 жыл бұрын
Hey brother, detailed video for sure but from the "Dodge" exploded views I looked at, you sir, have put the E-brake adjuster in backwards. i fear you may have trouble getting the adjuster backed off the next time you do the rears. You may NOT be able to gain access to the "star" nut on the adjuster. The star nut goes towards the front of the vehicle, so sez all the pics I've looked at. Hope it doesn't bite you in the butt, next time you do it. Cheers, Victor
@KendorFarms
2 жыл бұрын
Interesting, thanks, I’ll have to check that out
@Noname30000
Ай бұрын
Thanks for the vid! I use mine when loading/unloading equipment on a trailer. Noticed last week my p brake pedal now goes all the way to the floor now but still engages. Does your pedal only go down half way? I either snapped/stretched a cable or perhaps it was just getting bound up before.
@KendorFarms
Ай бұрын
Honestly I never use it, I should check it lol
@Jon-O.
Жыл бұрын
A can of brake clean does wonders
@alwayssharp
Жыл бұрын
Nice
@lukewarm1217
Жыл бұрын
What is a good deal on the cost of breaks?
@WebflingerJoe
Ай бұрын
Lmao each assembly used a different sized bolt in mine, 2 16's, 12's, 9/16 and 13's. Im just like wtf man
@gizmo-xc4eb
9 ай бұрын
That old rotor would make a great lamp or coat rake base.
@KendorFarms
9 ай бұрын
Or cash for scrap
@gambhirahcaitanya4393
2 жыл бұрын
thank you for the time. parts $270 and i can do it. Local midas: $850.
@ottomendez2404
2 жыл бұрын
What is the length of those 5!6 bolts you used to extract the drums out?.
@KendorFarms
2 жыл бұрын
I believe they were about 2 inch
@rox625
2 жыл бұрын
I take it this will be the same for a 3500 single wheel drive?
@KendorFarms
2 жыл бұрын
Yes it should be
@Mrjpmom1
11 ай бұрын
I have a 2013 2500 Ram diesel. I us it to tow my RV . My ? is when you apply your foot brake does that engage your rear brakes as well to slow down your truck. TIA
@KendorFarms
11 ай бұрын
You mean applying the emergency brake?
@Mrjpmom1
11 ай бұрын
@@KendorFarms no the regular brake when you apply it
@Mrjpmom1
11 ай бұрын
I just answered my own question but I enjoyed your KZitem video and thank you for getting back to me I appreciate the quick response
@countrycorner9337
2 жыл бұрын
What year is the truck? You should put that in the description.
@KendorFarms
2 жыл бұрын
2011, however rear brakes (pads and rotors) haven’t changed in a long time. If you can watch this with confidence to do your own, you’ll do just fine
@ottomendez2404
2 жыл бұрын
5/16 bolts
@so5thgen
4 ай бұрын
You installed passenger side adjuster in the wrong direction. It’ll never automatically adjust
@KendorFarms
4 ай бұрын
Yep, I did. Reversed it after 👍
@minituck04
6 ай бұрын
What brand rotors did you go with
@KendorFarms
5 ай бұрын
Honestly I can’t remember, I’m thinking power stop
@mathermp
2 жыл бұрын
Jack's stands
@peterhiengslough5901
Жыл бұрын
You skipped the one part I needed to see. How to get the parking brake shoes on with that yellow spring of doom.
@KendorFarms
Жыл бұрын
Haha I either put in on first then the shoes on or squeezed the hell out of it with side cutters to bit into it and pulled it over...
@bane1240
Жыл бұрын
What kind of grease is used for the inside of the pins ?
@KendorFarms
Жыл бұрын
Its a special caliper pin grease
@DinDooIt
10 ай бұрын
Sil Glyed brake lube.
@arcraider937
4 ай бұрын
Permatex 24125 ceramic extreme brake parts lubricant.
@joeeliyah2090
Жыл бұрын
Thanks for the vid. Buuuuuuuuut! #1 RULE when jacking anything up! DO NOT RELY ON THE JACK!!!!!!!Put jack stands under the axle first before working on the truck. If that jack fails your truck gets damaged and you could die by getting pinned under the vehicle or crushed. ALWAYS use jack stands and NEVER TRUST A JACK!!!!!
@KendorFarms
Жыл бұрын
Not a fan of jack stands at all. I've had one colapse. I crib it with 6x6's, feels safer.
@joeeliyah2090
Жыл бұрын
@@KendorFarms Thanks for your reply. Can you please show a vid about how that happened and how to crib it?
@roncharbonneau797
2 жыл бұрын
you don't adjust the ebrake pads?
@KendorFarms
2 жыл бұрын
Yep, after they ate installed. If you kno2 enough to adjust them then you should
@chadfiege7539
Жыл бұрын
Im pretty sure your "star wheel" was the wrong way. The star should be towards the front on the passenger side.
@KendorFarms
Жыл бұрын
Yep, it was
@troyd.521
2 жыл бұрын
What year is your truck?
@KendorFarms
2 жыл бұрын
That one is a 2011
@troyd.521
2 жыл бұрын
@@KendorFarms would it be pretty much the same as a 2014?
@KendorFarms
2 жыл бұрын
Yep for sure, maybe slight differences in the size but same method
@isaiahphillips2664
Жыл бұрын
Do I have to use the metal clips to hold pads or not?
@KendorFarms
Жыл бұрын
Not if the old ones are still good
@isaiahphillips2664
Жыл бұрын
@@KendorFarms they old and rusty I’ve seen some with out metal chips and some without so I wasn’t sure if I had to have them
@KendorFarms
Жыл бұрын
Yea it's definitely best to have them in there
@isaiahphillips2664
Жыл бұрын
@@KendorFarms ok I’ll put them on there and was the wet brake fluid called that you put on the pads
@KendorFarms
Жыл бұрын
The stuff I put on the pads is called disc quiet. It's not necessary, but just stops any possible squeaks later on
@angie19712
Жыл бұрын
dont you ever need to adjust them tho
@KendorFarms
Жыл бұрын
I don’t normally unless they need it
@jjb-rad804
2 жыл бұрын
Jack stands I hope 🤞
@jacobsebastien3910
2 жыл бұрын
Harbor freight makes the Best jack stands Lol' 😅
@YourDadsBoyfriend
2 жыл бұрын
@@jacobsebastien3910 This train of thought on a $60k++ truck is just pure ignorance imho. If you can afford the truck then you can afford the proper high quality safety equipment. But then again, I am a great admirer of Darwin. So have at it...
@KendorFarms
2 жыл бұрын
Sometimes you can't always believe what you see on the internet
@techi3075
2 жыл бұрын
If you need brakes, you NEED new flexible lines. The rubber lines look rough on the outside and they are always worse on the inside. Cheap insurance.
@jaxturner7288
Жыл бұрын
Bollicks. 😵💫
@angie19712
Жыл бұрын
TY SOOO MUCH. CUZ WHEN I'M doing our brakes, my boyfriend is equipped, yet hates them.. I'm in process and he's yellimgatmeto get out from his work truck cuuz I onluy seenOIOne serviceb brake assbly. Is this posssible.???? hjuh... anyway. I am ONLY ONE GIRL. HE'S A TOTAL D@@K. AND he's GOT ME UNDER THERE. WOW. !!! I only see one set of parking brake service cables. wtf.?????
Пікірлер: 96