I used 5200 and screwed into the deck floor, no backing plates, no access on my boat. In additon I have 2 mounts on each side in the console. Very sturdy, no problems or loosening. On Ship Shape TV and many other mountings, they use 5200 and screw directly into rhe deck.
@greauxpete
5 жыл бұрын
Thanks Scott!
@jefflindsey9589
5 жыл бұрын
Scott Ward Just did the same thing with 5200 and two standoff braces on each side of the cc. Very sturdy...
@romant1703
4 жыл бұрын
any suggestions on the screws?
@treyfrohne2592
4 жыл бұрын
This is gonna sound crazy but I bought this boat back in November in Kemah just checked the tx numbers and they match
@scottward8038
4 жыл бұрын
Hey Trey, I sold the boat, I hope you are enjoying it. Real clean boat. I moved up to a 21 foot.
@scottward8038
3 жыл бұрын
How is the SeaPro doing?, did you have a great summer with it?
@thomasneuffer4497
4 жыл бұрын
In some of the last pics with the top folded down you show the rear most section of top frame slightly folded. I have also seen other pics elsewhere where this piece is folded back onto itself. The joint on mine is pretty tight, I don't see that it can fold simply by removing one bolt on each side? Perhaps it just needs a little "persuasion"?
@scottward8038
4 жыл бұрын
I only needed to fold mine about 90 degrees where it would lay down onto the bow rail. You remove one screw same position on each side and loosen the others, you may have them to tight.
@greauxpete
5 жыл бұрын
Did u screw into the deck or use a nut and bolt with a backing plate (requiring access)? Not sure I can get access to underneath the floor on mine.
@romant1703
4 жыл бұрын
My Console doesn't have a curve, what happens if the standos are too long? Can they be cut or we just have to deal with it?
@scottward8038
4 жыл бұрын
You can cut them to fit. I had to shorten mine.
@matthewdesousa9760
4 жыл бұрын
Are there supposed to be openings on where the floor piece bolts into the top piece
@scottward8038
4 жыл бұрын
Not sure what part your asking about, but if your asking about where the top section meets the floor section, (the middle) it is not open tubing, it is welded with joints that slip together and have 2 fasteners that tighten together. This is where you remove the fastners to fold the top.
@DMD81773
4 жыл бұрын
Have the welds cracked yet. Ive been looking for one but found o line tge welds crack on some
@scottward8038
4 жыл бұрын
No issues at all with mine.
@MakDeddy2498
3 жыл бұрын
Do you tow it with it folded down or up ?
@scottward8038
3 жыл бұрын
You tow with it up, the manufacturer says not to tow with it folded.
@Zebra063
6 жыл бұрын
Do you have any problems getting in the garage folded down? Curios on the height and if it will fit on mine.
@scottward8038
6 жыл бұрын
No problems for me. My door is 7 foot. But i would also consider the height your boat sits on the trailer. It is close for me with about 3 inches. I do have to remove my windshield, use quick fastners on it.
@scottward8038
6 жыл бұрын
David Lee no problems at 7 foot opening. I do remove the windshield and had to prior to the t top. The top folded on my boat is lower then the window top edge.
@jamessprague5653
6 жыл бұрын
I have a MAKO 18LTS. Do you think I can get in my garage with this boat? 7' Door height
@scottward8038
6 жыл бұрын
James Sprague my garage is 7ft also. One factor is how high does your boat sit on the trailer. You should try to measure the floor of your boat down to the ground, then add the height of the folded dimensions. Mine is high, the mako looks lower
Пікірлер: 29